Home Styles 88 5318 95 User manual

88 5318 95
Kitchen Cart
Home Styles Consumer Assistance : www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Hardware List
Part List
IMPORTANT NOTE.
Tools required for assembly : Phillips screwdriver
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damage occurring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure
a completed product as it was designed.
A.
To p
1 Pc.
B.
Side Frame
1 Pc.
C.
Side Frame
1 Pc.
D.
Divider
1 Pc.
E.
Front Rail
1 Pc.
F.
Back Rail
1 Pc.
G.
Shelf
2 Pcs.
H.
Drawer
2 Pcs.
(Knock-Down Construction,
please refer to the last page of
instructions for steps to complete drawer assembly)
Hex Wrench
1 Pc.
Small Hex Wrench
1 Pc.
M6x25
Head Cap Bolt (short)
5 Pcs.(+1 extra)
M6x50
Head Cap Bolt (long)
8 Pcs. (+1 extra)
Flat Washer
8 Pcs. (+1 extra)
Spring Washer
8 Pcs. (+1 extra)
Side Bar
2 Pcs.
Pull Handle
2 Pcs.
M4x24
Cam Lock Screw
13 Pcs. (+1 extra)
Cam Lock
13 Pcs. (+2 extra) Machine Screw
4 Pcs.
M3.5x25
Wood Screw (long)
for side drawer
16 Pcs. (+1 extra)
M3.5x13
Wood Screw (short)
for bottom drawer
12 Pcs. (+1 extra)
Caster
2 Locking
2 Non-Locking
4 Pcs.
M4x25

Assembly Instructions 2/6
IMPORTANT
* Please keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future.
* Do not tighten up all the bolts until each part is properly assembled.
* Use a soft cloth between these parts and the floor.
STEP 1
Remove the Supports from
Side Frames (B) and (C).
Insert Cam Lock Screws into pre-drilled holes of Top (A),
STEP 2
Side Frames (B) and (C), and Back Rail (F).
B
B
C
C
F
A
Support
Cam Lock Screw

Assembly Instructions 3/6
and Head Cap Bolt (short).
Attach unit to Side Frame (B) with Cam Locks.
(See Figure 1)
Attach Shelves (G) to unit with
STEP 4
Flat Washers, Spring Washers and Head Cap Bolts (long).
(See Figure 2)
Figure 1Figure 1
BE
G
G
D
F
Cam Lock
Cam Lock Screw
Head Cap Bolt (short)
Flat Washer
Spring Washer
Head Cap Bolt
(long)
Flat Washer
Spring Washer
Head Cap Bolt (long)
Figure 2
STEP 3
Assemble Front Rail (E), Divider (D) and Back Rail (F) with Cam Lock

Assembly Instructions 4/6
STEP 5
Attach Side Frame (C) to unit with Cam Lock, Flat Washers
Spring Washers and Head Cap Bolts (long).
C
Head Cap Bolt (long)
Spring Washer
Flat Washer Flat Washer
Spring Washer
Head Cap Bolt
(long)
Cam Lock
Locking Caster
Non-Locking
Caster
STEP 6
Attach the Casters to the legs of unit.

Assembly Instructions 5/6
STEP 7
Turn the unit to its’ upright position.
Attach Side Bars to unit with Head Cap Bolts (short).
(See Figure 3)
Place Top (A) onto unit with
STEP 8
Cam Locks.
Slide Drawers (H) into place.
Head Cap Bolt
(short)
Side Bar
Figure 3
A
Cam Lock
H
H

Assembly Instructions 6/6
Part List
H1.
Front Part
2 Pcs.
H3.
Side Part
2 Pcs.
H4.
Side Part
2 Pcs.
H5.
Bottom Part
2 Pcs.
H2.
Back Part
2 Pcs.
Drawer (H)
H3
H3
H4
H4
H5
H5
H1
H1
H2
H2
STEP 1
Attach H1 to H3 and H4,
using a Phillips screwdriver and
long wood screws (4X),
tighten halfway.
Attach H2 to H3 and H4 using
long wood screws (4X),
tighten halfway. (See Figure 1)
Slide H5 into the grooves in H3 and H4.
STEP 2
Be sure to push H5 all the way forward so it meets H1
(See Figure 2)
STEP 3
Insert short wood screw (6X)
into pre-drilled holes in H5 and tighten.
(See Figure 3)
Assemble Pull Handle with
STEP 4
machine screws. (See Figure 4)
Tighten all screws used in drawer assembly.
Figure 1
Figure 2
Figure 3
Figure 4