Home Styles 88 5217 95C User manual

Part List
Hardware List
B.
Side Frame
.1 pc
A.
Top
1 pc.
Hex Wrench
1 pc.
Caster
Two casters with lock
Two casters without lock
4 pcs.
Machine Screw
for Pull Handle
4 pcs.
Pull Handle
2 pc.
Head Cap Bolt
15 pcs. (+1Extra)
Wood Screw
Short 6 x ½
(for Drawer Bottom Part)
”
12 pcs.(+1 Extra)
Wood Plug
13 pcs.
(+1 Extra)
Wood Screw
Long 6 x 1
(for Drawer Side Part)
”
16 pcs.(+1 Extra)
D.
Front Rail
2 pcs.
E.
Back Rail
1 pc.
F.
Divider
1 pc.
H.
Shelf
1 pc.
I.
Drawer
(Knock-Down Construction, please refer to
the page (4/4) of these instructions for
steps to complete assembling drawers)
2 drawers
C.
Side Frame
1 pc.
Head Cap Bolt (short)
(for Side Bar)
2 pcs. (+1 Extra)
G.
Base
1 pc.
J.
Side Bar
1 pc.
88 5217 95C
Stainless Steel Top Kitchen Island
Supporting Pin
(+1 Extra)4 pcs.
Cam Lock Screw
4 pcs.(+1 Extra)
Cam Lock
4pcs.(+1 Extra)
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
Tools Required For Assembly : Phillips screwdriver
Home Styles Consumer Assistance Line 888-680-7460 and 877-831-0319
[email protected]
Small
Hex Wrench
1 pc.
Revised date : 24Mar2011

IMPORTANT
Do not tighten up all the screws until each part is properly assembled. You should keep Hex Wrench in the safe place as
you may need to tighten up the Head Cap Bolts in the future.
STEP 1
STEP 2
STEP 3
E
D
D
D
F
Attach the Divider (F) and another
Front Rail to the assembled unit.
Attach the Front Rail (D)
and Back Rail (E) to the
Side Frame (B).
Assembly Instructions 2/4
B
B
Turn the Side Frame (B) upside down
on the soft material.
Attach the locking caster to the leg with sign,
and the non-locking caster to the other leg.
Do the same for the Side Frame (C).
Head Cap Bolt
Locking Caster
Non-Locking Caster
Head Cap Bolt
Head Cap Bolt
Head Cap Bolt

Assembly Instructions 3/4
STEP 4
STEP 5
STEP 7
STEP 6
Cover all holes with Wood Plugs
Attach the Base (G)
and Side Frame (C)
to the assembled unit.
Attach the Side Bar (J)
to the Side Frame (C).
C
C
J
A
II
H
G
Head Cap Bolt
Head Cap Bolt
Head Cap Bolt
Head Cap Bolt (short)
Cam Lock
Cam Lock Screw
Supporting Pins Supporting Pins
Place the Top (A) on the assembled unit.
Place the Cam Locks into the holes of the
Side Frame (B) and (C).
Tighten up all the Cam Locks to secure
the Top with the body. Insert the Supporting Pins
into both side frames at the desired level.
Place Shelf (H) and slide the Drawers (I)
into place.
Make sure the Arrow sign
is on top.
Put the Cam Lock Screws into the holes at the
back of the Top (A).
A
See the “Arrow”
on top

Assembly Instructions 4/4
Slider Wheel
I2
I3
I4 I1
I1
Figure 1
Line up Side Parts (I3) and (I4) to the
Front Part (I1) and Back Part (I2). Make sure
the sign on each part is going down.
Using a screwdriver, insert 1” screws
into each of the 4 pre-drilled holes on the
sides
Philips
(I3) and (I4), then tighten half way.
Drawer
Part List
I1.
Front Part
2pcs.
I5.
Bottom Part
2 pcs.
I2.
Back Part
2 pcs.
Figure 2
Figure 3
Turn the assembled drawer over and slide the
Plywood Bottom Part (I5) into the grooves
of Side Parts Be sure to push
the plywood bottom part all the way forward,
so it meets the Front Part (I1).
(I3) and (I4).
Insert the remaining ” screws (6 pcs.)
into the pre-drilled holes at the Bottom Part
(I5), then tighten up all screws
½
I4
I2
I5
I1
I3
I3.
Side Part
2 pcs.
I4.
Side Part
2 pcs.
Assemble the Pull Handle
with Machine Screw.
to the Front Part (I1)
* If you are missing any of these
parts, please contact our DMI
Customer Service Department
at 1-877-831-0319 or fax us at
1-800-755-2878.