Home Styles Cabin Creek 5411-351 User manual

Hardware List
Part List
Tool(s) required for assembly: Level
Carton 5411 352 is also needed for assembly.-
Bar Table
Hex Wrench
1c.p
Small Hex Wrench
1 pc.
M8x45
Head Cap Bolt (long)
8 cs. (+1 extra)p
Spring Washer
8 cs. (+1 extra)p
Flat Washer
8 cs. (+1 extra)p
A.
Top
1 pc.
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
M6x16
Head Cap Bolt (short)
5 pcs. (+1 extra)
Having issues assembling?
Important piece go missing?

Part List
Bar Table
IMPORTANT
For assembly see instructions in carton 5411 351.-
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
B.
Leg
4 pcs.
C.
Stretcher
1 pc.
D.
Stretcher
1 pc.
Having issues assembling?Ha
Important piece go missing?

Assembly Instructions 2/3
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as the bolts may need to be tightened in the future.
STEP 1
Attach Stretcher (D) to Stretcher (C)
with Head Cap Bolt (short), tightening
bolt only halfway. (See Figure 1)
C
D
Figure 1
Figure 2
STEP 2
Place Top (A) upside down on a soft cloth.
Attach Legs (B) to Top (A) with Flat Washers,
Spring Washers and Head Cap Bolts (long),
tightening bolts only halfway. (See Figure 2)
Attach unit from Step 1 to unit with
Head Cap Bolts (short), tightening bolts only halfway.
A
B
B
B
Flat Washer
Spring Washer
Head Cap Bolt (long)
Head Cap Bolt (short)
Head Cap Bolt (short)

Assembly Instructions 3/3
Figure 3
STEP 4
Turn unit over to its upright position.
Level unit by adjusting the adjustable
levelers on bottom of legs.
(See Figure 3)
Note: Unit must be level to work properly.
STEP 3
Attach Leg (B) to unit with Flat Washers,
Spring Washers, Head Cap Bolts (long)
and Head Cap Bolt (short),
tightening bolts only halfway.
Tighten all bolts used in Steps 1, 2 and 3.
Head Cap Bolt (long)
Spring Washer
Flat Washer
B
Head Cap Bolt (short)

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
Do not use commercial
waxes and polishes.
PREVENT
DISCOLORING
PREVENT
YELLOWING
PREVENT
FINISH DAMAGE
Do not place hot
objects on surface.
Do not write
directly on surface.
Do not use power tools
above 8 volts
to assemble.
PREVENT
MARKING
PREVENT
CRACKING
PREVENT
FADING
Do not place
in direct sunlight.
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
homestyles will provide replacements free of charge for missing or damaged hardware or parts within 30 days
of purchase. Digital images of the defective parts may be required. If the product was not purchased from an
authorized retail affiliate, homestyles is under no obligation to provide replacement parts. Parts are not available for
fully assembled items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be
requested at:
where applicable