Home Styles 88 5515 16 User manual

88 5515 16
Desk
Student
PART LIST
HARDWARE LIST
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the wood parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
A.
Top
1 pc.
E.
Side Frame
1 pc.
F.
Side Frame
1 pc.
D.
Front Frame
1 pc.
C.
Divider
1 pc.
G.
Stretcher
1 pc.
H.
Drawer
1 pc.
I.
Drawer
1 pc.
B.
Back Stretcher
1 pc.
(M6x35)
Head Cap Bolt
14 pcs. (+1 extra )
(M6x28)
Head Cap Bolt (short)
2 pcs. (+1 extra )
Flat Washer
16 pcs. (+1 extra )
Hex Wrench
1 pc.
Small Hex Wrench
1 pc.
Spring Washer
16 pcs. (+1 extra )
(M3x38)
Wood Screw
2 pcs. (+1 extra)
Tools required for assembly : Tools recommended for assembly :Phillips screwdriver Level
Home Styles Consumer Assistance: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
(Please refer to the last page(s) of these instructions for drawer assembly steps.)

STEP 1
Place Top (A) upside down on a soft cloth.
Attach Back Stretcher (B), Divider (C) and Front Frame (D) to Top (A) with Flat Washers,
Spring Washers, Head Cap Bolts (short) and Head Cap Bolts. (See Figure 1)
IMPORTANT
* Do not tighten up all the bolts and screws until each part is properly assembled.
* You should keep Hex Wrench in a safe place as you may need to tighten up the Bolts in the future.
* Use a soft cloth between these parts and the floor.
* After assembly, item must be level to work properly. Use the included adjustable levelers to level.
Assembly Instructions 2/4
A
D
C
B
Figure 1
Head Cap Bolt
Spring Washer
Flat Washer
Head Cap Bolt (short)
Spring Washer
Flat Washer
Wood Screw
STEP 2
Attach Side Frame (E) to unit with
Flat Washers, Spring Washers and Head Cap Bolts.
Attach Stretcher (G) to unit with Wood Screw.
Attach Side Frame (F) to unit with Wood Screw, Flat Washers, Spring Washers and Head Cap Bolts.
G
F
E

Assembly Instructions 3/4
STEP 3
Turn the unit over to its’ upright position.
Slide Drawers (H) and (I) into position.
To level the unit, adjust the adjustable levelers on the bottom of unit.
(See Figure 2)
Note: Unit must be level to work properly.
Figure 2
H
I

Assembly Instructions 4/4
H2
H2
H2
H2
H3
H3
H3
H3
H4
H4
H4
H4
H5
H5
H1
I1
Drawer (H)
Drawer (I)
Part List
H1.
Drawer Front
1 pc.
I1.
Drawer Front
1 pc.
H5.
Drawer Bottom
2 pcs.
H2.
Drawer Back
2 pcs.
H3.
Drawer Side
2 pcs.
H4.
Drawer Side
2 pcs.
Attach H2 to H3 and H4, then flip the Locks.
(See Figures 3 and 4)
Attach H2 to H3 and H4, then flip the Locks.
(See Figures 3 and 4)
Slide H5 into the grooves in H3 and H4.
Be sure to push H5 all the way forward so it meets H2.
Attach H1 to unit, then flip the Locks.
Slide H5 into the grooves in H3 and H4.
Be sure to push H5 all the way forward so it meets H2.
Attach I1 to unit, then flip the Locks.
STEP 1
STEP 1
STEP 2
STEP 2
Figure 3 Figure 4
I
H