Home Styles 5092 942 User manual

Part List
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Tool(s) required for assembly: Phillips screwdriver, Level
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Kitchen Island
5092 942-
Carton 5092 941 is also needed for assembly.-
B.
Rail
2 pcs.
C.
Side Panel
2 pcs.
D.
Post
2 pcs.
E.
Post
2 pcs.
G.
Shelf
4 pcs.
H.
Door
2 pcs.
I.
Door
2 pcs.
J.
Shelf
1 pc.
K.
Base
1 pc.
L.
Stretcher
2 pcs.

Assembly Instructions 2/5
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as the bolts may need to be tightened in future.
Cam Lock Screw
Figure 1
STEP 1
Remove drawer from Top (A).
Attach Knobs to drawer
with Machine Screws.
STEP 2
Insert Cam Lock Screws into pre-drilled
holes in Side Panels (C), then tighten.
(See Figure 1)
CC
A
Knob
Machine Screw

Assembly Instructions 3/5
Figure 2
STEP 3
Attach Side Panels (C) to
Rails (B) with Cam Locks.
(See Figure 2) C
C
B
B
Cam Lock
STEP 4
Place Top (A) upside down on a soft cloth.
Attach unit to Top (A).
Figure 3
A
STEP 5
Attach Stretchers (L) to Posts (D)
and (E) with Head Cap Bolts.
(See Figure 3)
LL
D
ED
E
Head Cap Bolt

Assembly Instructions 4/5
STEP 6
Attach Shelves (G) to unit from Step 4.
Attach units from Step 5 to unit with Head Cap Bolts.
STEP 7
Attach Base (K) to unit
with Head Cap Bolts.
Head Cap Bolt
D
E
E
D
G
GG
G
Head Cap Bolt
K

Assembly Instructions 5/5
Figure 6
Figure 4
Figure 5
STEP 9
Turn unit over to its upright position.
Insert Adjustable Pins into
side panels at desired level.
Place Shelf (J) into position.
Attach Doors (H) and (I) to
unit by sliding door hinges
into side panel hinges.
(See Figure 5)
Attach Knobs to Doors (H)
and (I) with Machine Screws.
(See Figure 6)
Slide drawer into position.
Level unit by adjusting the
adjustable levelers on
bottom of unit.
(See Figure 7)
Figure 7
Head Cap Bolt (long)
Spring Washer
Flat Washer
STEP 8
Attach Feet (F) to unit with
Flat Washers, Spring Washers
and Head Cap Bolts (long).
(See Figure 4) F F
F
F
H
IH
I
J
Knob
Machine Screw
Adjustable Pin

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestyles-furniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319