Home Styles 20 08000 0181 User manual

Hardware List
Part List
Home Styles Customer Service: www.homestyles-furniture.com,
[e-mail], 888-680-7460, 877-831-0319
Tool(s) required for assembly: Phillips screwdriver, Level
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
20 08000 0181
Pedestal Desk
Carton 20 08000 0182 is also needed for assembly.
Cam Lock Screw
76 pcs. (+1 extra)
Cam Lock
52 pcs. (+6 extra)
Dowel
36 pcs. (+1 extra)
M3.5x64
Wood Screw
16 pcs. (+1 extra)
M3.5x16
Flat Head Screw (short)
6 pcs. (+1 extra)
Cam Lock (small)
24 pcs. (+4 extra)
Cover
4 pcs. (+1 extra)
M3.5x38
Flat Head Screw (long)
20 pcs. (+1 extra)
M3.5x25
Flat Head Screw
28 pcs. (+1 extra)
N.
Keyboard
1 pc.
L.
Drawer
4 pcs.
M.
Drawer
2 pcs.
A.
Top
1 pc.
O.
Metal Strip
4 pcs.
Refer to later page(s) of these instructions
for drawer and keyboard assembly.

Assembly Instructions 2/10
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Make sure unit is level before tightening these screws.
The unit must be level to work properly. Use the included adjustable levelers to level.
Figure 1
STEP 1
Place Top (A), Side Panels (B), (E),
Middle Panels (C), (D)
and Plinths (I) on a soft cloth.
Insert Cam Lock Screws into
pre-drilled holes in Top (A),
Side Panels (B), (E),
Middle Panels (C), (D)
and Plinths (I), then tighten.
(See Figure 1)
I
HI
H
Cam Lock
I
HI
H
Figure 2
B
C
D
E
I
II
I
A
Cam Lock Screw
STEP 2
Attach Plinths (I) to Plinths (H) with Cam Locks.
(See Figure 2)

Assembly Instructions 3/10
STEP 5
Insert Dowels into pre-drilled holes in unit.
Attach unit from Step 2 to unit with Wood Screws.
Turn unit over to its’ upright position.
Wood Screw
Dowel
STEP 3
Insert Dowels into pre-drilled holes
in Back Panel (J). (See Figure 3)
Attach Side Panel (B) and Middle Panel (C)
to Back Panel (J) with Cam Locks.
B
CJ
Dowel
Figure 3
Figure 4
Dowel
F
Cam Lock
Flat Head Screw (long) STEP 4
Insert Dowels into pre-drilled holes in unit.
Attach Base (F) to unit with Flat Head Screws (long).
(See Figure 4)

Assembly Instructions 4/10
STEP 6
Insert Dowels into pre-drilled
holes in Back Panel (J).
Attach Middle Panel (D) and Side Panel (E)
to Back Panel (J) with Cam Locks.
STEP 8
Insert Dowels into pre-drilled holes in unit.
Attach unit from Step 2 to unit with Wood Screws.
Turn unit over to its’ upright position.
Dowel
D
J
E
Wood Screw
Dowel
STEP 7
Insert Dowels into pre-drilled holes in unit.
Attach Base (F) to unit with Flat Head Screws (long).
F
Dowel
Flat Head Screw (long)
Cam Lock

Assembly Instructions 5/10
STEP 9
Insert Dowels into pre-drilled holes in unit from Step 5.
Attach Rail (G) and Back Panel (K) to unit with Cam Locks.
Cover Cam Locks with Covers. (See Figure 5)
Cam Lock
Dowel
G
K
Cover
STEP 10
Insert Dowels into pre-drilled holes in unit.
Attach unit from Step 8 to unit with Cam Locks.
Cover Cam Locks with Covers.
Dowel
Cam Lock
Cover
Figure 5

Assembly Instructions 6/10
STEP 11
Insert Dowels into pre-drilled holes in unit.
Attach Top (A) to unit with Cam Locks.
Level unit by adjusting the adjustable levelers on bottom of unit.
(See Figure 6)
Note: Unit must be level to proceed. Figure 6
A
Cam Lock
Dowel

Part List
Assembly Instructions 7/10
STEP 13
Slide Drawer Bottom (L5) into groove.
L1.
Drawer Front
4 pcs.
L2.
Drawer Back
4 pcs.
L3.
Drawer Side
4 pcs.
L4.
Drawer Side
4 pcs.
L5.
Drawer Bottom
4 pcs.
Drawer (L)
STEP 12
Insert Cam Lock Screws into pre-drilled
holes in Drawer Front (L1), then tighten.
Attach Drawer Sides (L3) and (L4)
to Drawer Front (L1) with Cam Locks (small).
L1
L3
L4
L5
L2
Flat Head Screw
STEP 14
Attach Drawer Back (L2) to unit with Flat Head Screws.
Cam Lock Screw
Cam Lock (small)

Part List
Assembly Instructions 8/10
M1.
Drawer Front
2 pcs.
M2.
Drawer Back
2 pcs.
M3.
Drawer Side
2 pcs.
M4.
Drawer Side
2 pcs.
L5.
Drawer Bottom
2 pcs.
STEP 16
Slide Drawer Bottom (L5) into groove.
Drawer (M)
STEP 15
Insert Cam Lock Screws into pre-drilled
holes in Drawer Front (M1), then tighten.
Attach Drawer Sides (M3) and (M4)
to Drawer Front (M1) with Cam Locks (small).
M1
M3
M4
L5
M2
Flat Head Screw
STEP 17
Attach Drawer Back (M2) to unit with Flat Head Screws.
STEP 18
Place Metal Strips (O) into position.
Metal Strips (O) can be adjusted
for letter or legal files.
O
Legal Size
Letter Size
Cam Lock Screw
Cam Lock (small)

Part List
Assembly Instructions 9/10
N1.
Keyboard Front
1 pc.
N2.
Keyboard Back
1 pc.
N3.
Keyboard Side
1 pc.
N4.
Keyboard Side
1 pc.
N5.
Keyboard Bottom
1 pc.
Keyboard (N)
Flat Head Screw
N2
N3
N4 STEP 19
Attach Keyboard Sides (N3) and (N4)
to Keyboard Back (N2) with Flat Head Screws.
Figure 7
STEP 21
Turn unit over to its’ upright position.
Attach Keyboard Front (N1) to unit
with Flat Head Screws (short).
(See Figure 7)
N1
Flat Head Screw (short)
Flat Head Screw (long)
STEP 20
Attach Keyboard Bottom (N5)
to unit with Flat Head Screws (long).
N5

Assembly Instructions 10/10
STEP 22
Slide Drawers (L), (M) and Keyboard (N) into position.
Note: To remove Drawers (M) and Keyboard (N) in future, push plastic lever on left side up,
push plastic lever on right side down and pull open. (See Figures 8 and 9)
Figure 9
Figure 8
Left Side Right Side
L
M
LL
M
L
N