Home Styles 4515-95 User manual

Hardware List
Part List
Home Styles Customer Service: www.homestylesfurniture.com,
[email protected], 888-680-7460, 877-831-0319
Tool(s) required for assembly: Phillips screwdriver
4515-95
Kitchen Cart
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
J.
Front Rail
1 pc.
Q.
Shelf
4 pcs.
R.
Door
1 pc.
S.
Door
1 pc.
L.
Tower Bar
1 pc.
K.
Arm
2 pcs.
P.
Rack
1 pc.
O.
Rack Base
1 pc.
M.
Rack Side
1 pc.
N.
Rack Side
1 pc.
A.
Top
1 pc.
T.
Drawer
2 pcs.
B.
Side Panel
1 pc.
C.
Side Panel
1 pc.
H.
Back Rail
1 pc.
G.
Back Upright
2 pcs.
D.
Middle Panel
1 pc.
E.
Middle Panel
1 pc.
F.
Back Panel
3 pcs.
Handle
4 pcs.
M3x16
Wood Screw (short)
20 pcs. (+1 extra)
Magnet
2 pcs.
M3x16
Wood Screw
for Magnet
4 pcs. (+1 extra)
M4x25
Wood Screw (long)
24 pcs. (+1 extra)
M4x22
Machine Screw
8 pcs.
Adjustable Pin
16 pcs. (+1 extra)
Hex Wrench
1 pc.
Small
Hex Wrench
1 pc.
M6x12
Head Cap Bolt
for Caster
16 pcs. (+1 extra)
M6x25
Head Cap Bolt
4 pcs. (+1 extra)
M6x38
Head Cap Bolt (long)
4 pcs. (+1 extra)
Refer to later page(s) of these
instructions for drawer assembly.
U.
Base
1 pc.
W.
Front Rail
1 pc.
I.
Back Rail
1 pc.
M3.5x25
Flat Head Screw
3 pcs. (+1 extra)
Caster
2 Locking
2 Non-Locking
4 pcs.

Assembly Instructions 2/7
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
Keep Hex Wrench as the bolts may need to be tightened in the future.
STEP 1
Assemble Rack Sides (M), (N), Rack Base (O) and Rack (P).
M
N
OP
STEP 2
Attach unit to Side Panel (C) with Head Cap Bolts.
C
Head Cap Bolt
B
K
K
STEP 3
Attach Arms (K) to Side Panel (B) with Head Cap Bolts.
Head Cap Bolt

Assembly Instructions 3/7
Figure 3
STEP 5
Attach Base (U) to unit with
Head Cap Bolts (long),
then flip Locks.
(See Figure 3)
Note: Arrow label
indicates front of Base (U).
STEP 4
Attach Back Rail (H) to Side
Panel (C), then flip Locks.
(See Figures 1 and 2)
Attach Back Uprights (G) to unit.
Slide Back Panels (F) into position.
Attach Back Rail (I) to
unit, then flip Lock.
Attach Side Panel (B) to
unit, then flip Locks.
Lock
F
G
I
FF
G
H
C
B
Figure 1 Figure 2
Head Cap Bolt (long)
Lock
Arrow label at front
U

Figure 4
STEP 6
Attach Casters to unit with Head Cap Bolts
for Caster into pre-drilled holes, with
Locking Casters at front. (See Figure 4)
Note: Arrow label indicates front of unit.
Arrow label at front
Locking Caster
Non-Locking Caster
Head Cap Bolt for Caster
Assembly Instructions 4/7
Wood Screw for Magnet
Magnet
STEP 7
Attach Magnets to Front Rail (W)
by inserting Wood Screws for Magnet
into pre-drilled holes, then tighten.
(See Figure 5)
Figure 5
W

Figure 7
Figure 6
Assembly Instructions 5/7
L
D
E
J
Wood Screw (short)
Lock
STEP 8
Turn unit over to its upright position.
Attach Middle Panel (D)
to unit, then flip Locks.
Attach Front Rail (J) and
Middle Panel (E) to unit,
then flip Lock.
Insert Wood Screws (short)
into pre-drilled holes in unit,
then tighten.
Slide Towel Bar (L) into position.
STEP 9
Insert Adjustable Pins into
side panels and middle panels
at desired level. (See Figure 6)
Place Shelves (Q) into position.
Attach Doors (R) and (S) by sliding door hinges into side panel hinges. (See Figure 7)
Attach Handles to Doors (R) and (S) with Machine Screws.
Attach Front Rail (W) to unit, then flip Locks.
Pull Handle
Machine Screw
Adjustable Pin
Q
Q
Q
Q
R
S
W

Part List
Assembly Instructions 6/7
STEP 11
Slide Drawer Bottom (T5) into groove.
Attach Drawer Bottom (T5) to
unit with Wood Screws (short).
STEP 12
Attach Handle with Machine Screws.
Handle
Machine Screw
Drawer (T)
STEP 10
Attach Drawer Front (T1) and Drawer
Back (T2) to Drawer Side (T3)
with Wood Screws (long).
Attach Drawer Side (T4) to unit
with Wood Screws (long).
Roller at back
T1
T2
T3
T4
Bottom
Wood Screw (long)
T5
Wood Screw (short)
T2.
Drawer Back
2 pcs.
T3.
Drawer Side
2 pcs.
T4.
Drawer Side
2 pcs.
T5.
Drawer Bottom
2 pcs.
T1.
Drawer Front
2 pcs.

Assembly Instructions 7/7
STEP 13
Attach Top (A) to unit with Flat Head Screws, then flip Locks.
Slide Drawers (T) into position.
A
Lock
Flat Head Screw
T
T

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestylesurniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestylesfurniture.com,
[email protected], 888-680-7460, 877-831-0319