Home Styles Lafayette 88 5537 07 User manual

Part List
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the wood parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed. Casual Attire For Today's Home
Tools required for assembly : Phillips screwdriver
Home Styles Consumer Assistance Line 888-680-7460 and 877-831-0319
[email protected]
Hardware List
A.
Top
1 pc.
K.
Plinth
1 pc.
88 5537 07
The
Corner Entertainment
Lafayette
Cam Lock Screw
26 pcs.(+1 extra)
Adjustable Pin
24 pcs.(+1 extra)
Pull Handle
2 pcs.
Machine Screw
2 pcs.
L.
Shelf
2 pcs.
M.
Shelf
4 pcs.
N.
Door
1 pc.
O.
Door
1 pc.
F.
Base
.1 pc
G.
Back Panel
.1 pc I.
Back Panel
.1 pc
H.
Back Panel
.1 pc
J.
Back Panel
.1 pc
B.
Side Panel
.1 pc
D.
Middle Panel
.1 pc
C.
Side Panel
1 pc.
E.
Middle Panel
1 pc.
Flat Washer
for Wood Screw
13 pcs. (+1 extra )
Wood Screw
for Base and
Back Panel
13 pcs.(+1 extra)
Wood Screw
for Magnet
4 pcs.(+1 extra)
Magnet
2 pcs.
Nail
2 pcs.(+1 extra)
Steel Plate
for Pull Handle
Attachment
1 pc.
Hex Wrench
1 pc.
Cam Lock
26 pcs.(+2 extra)
Wood Screw
for Plinth
2 pcs.(+1 extra)

IMPORTANT
Do not tighten screws until each part is properly assembled.
STEP 1
Assembly Instructions 2/4
A
Wood Screw
Magnet
Cam Lock Screw
K
B
C
Attach 2X Magnets
to pre-drilled holes of Top (A)
with Wood Screws.
Insert Cam Lock Screws into
the pre-drilled holes of Top (A),
Side Panel (B) and (C),
Back Panel (I) and (J),
Plinth (K), then tighten.
I
J

D
E
K
F
I
B
C
J
Flat Washer
Wood Screw
Figure 1
Attach Middle Panels (D) and (E)
to Base (F) using Flat Washers
and Wood Screws.
STEP 2
STEP 3
Attach Back Panels (I) and (J),
Side Panels (B) and (C) to unit
with Cam Locks. (see Figure 1)
Attach Plinth (K) to the unit with Cam Locks.
Tighten 2X wood screws into Plinth.
Assembly Instructions 3/4
Wood Screw
(for Plinth)

Flat Washer
Wood Screw
G
H
A
Assemble Pull Handles to Door (N) and (O) with Machine Screws, then u
(see Figure 3)
Attach Door (N) and (O) to the side panels, by sliding the door lift hinges into the side panels
lift hinges. (see Figure 4)
se the Steel Plate to
firmly push the nail through the hole in the Pull Handle and into the pre-drilled hole in the door.
Attach Back Panel (G) and (H)
to the unit with Flat Washers
and Wood Screws.
Figure 4
STEP 5
O
N
M
M
M
L
LM
Figure 2
Figure 3
Adjustable Pin
Place Top (A) onto unit with Cam Locks.
Insert Adjustable Pins into side panels and middle panels at the desired level
(see Figure 2), then place Shelves (L) and (M) into position.
Assembly Instructions 4/4
STEP 4
Nail
Steel Plate
Adjustable
Pin