Home Styles Naples Entertainment Stand 88 5530 09 User manual

Part List
Hardware List
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the wood parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
Tools required for assembly : Phillips screwdriver
88 5530 09
Naples
Entertainment Stand
Home Styles Consumer Assistance: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Cam Lock
29 pcs.(+6 extra)
Cam Lock Screw
29 pcs.(+2 extra)
Adjustable Pin
12 pcs.(+1 extra)
Pull Handle
2 pcs.
Machine Screw
2 pcs.
Wood Screw
for Plinth
2 pcs.(+1 extra)
Wood Screw
for Back Panel
8 pcs.(+1 extra)
Wood Screw
for Wood Block
12 pcs.(+1 extra)
E.
Base
1 pc.
M.
Shelf
2 pcs.
A.
Top
1 pc.
G.
Plinth
1 pc.
N.
Front Rail
1 pc.
F.
Back Support
1 pc.
B.
Side Panel
.1 pc
C.
Side Panel
1 pc.
D1.
Middle Panel
.1 pc
D2.
Middle Panel
.1 pc
H.
Back Panel
2 pcs.
I.
Back Panel
1 pc.
J.
Door
1 pc.
K.
Door
1 pc.
L.
Shelf
1 pc.
O.
Wood Block
4 pcs.

IMPORTANT
*Do not tighten up all the screws until each part is properly assembled.
*Use a soft cloth between these parts and floor.
STEP 1
Assembly Instructions 2/5
G
A
B
E
C
Cam Lock Screw
Attach 2X Wood Blocks
(O) to Top (A) and
Base (E) by using Wood Screws
for Wood Block into the pre-drilled holes.
Insert Cam Lock Screws into the
pre-drilled holes
of Top (A), Side Panel (B) and (C),
Base (E), Plinth (G).
O
O
O
O
Wood Screw
for Wood Block
Wood Block
Wood Screw
for Wood Block
Wood Block

D1
D2
STEP 3
Assembly Instructions 3/5
Cam Lock
Screw
Cam Lock
Figure 1
Put the Cam Lock Screws into
the pre-drilled holes at the underside of Base (E).
Attach Back Support (F) to the unit with Cam Locks.
Cam Lock Screw
Cam Lock
F
E
E
STEP 2
Attach Middle Panel (D1)
and (D2) onto Base (E)
with Cam Locks. (see Figure 1)

Assembly Instructions 4/5
N
B
C
G
Cam Lock Screw
Cam Lock
STEP 4
G
Magnet
Attach Plinth (G) to the unit with Cam Locks.
Attach Side Panel (B) and Front Rail (N) to the unit with Cam Locks,
then attach Side Panel (C) to the unit with Cam Locks.
Tighten up 2X Wood Screws for Plinth
K
Figure 2
Slide Back Panels (H) and (I) into place.
Attach Doors (J) and (K) by sliding the door lift hinges into the side panels lift hinges.
(see Figure 2)
Assemble Pull Handles to Doors (J) and (K) with Machine Screws. (see Figure 3)
JH
I
H
STEP 5
Wood Screw
(for Plinth)
Figure 3

A
M
M
L
Adjustable Pin
Cam Lock
Place Top (A) onto the unit, using Cam Locks.
Insert Adjustable Pins into side panels and middle panels at the desired level.
Place Shelves (L) and (M) into position.
STEP 7
STEP 6
Assembly Instructions 5/5
Figure 4
Insert 8X Wood Screws from the back of the unit,
tighten up all the Wood Screws. (See figure 4)
Note: Please make sure unit is level before tightening these screws.