Home Styles 5053-49 User manual

Hardware List
Part List
5053-49
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Hall Tree
Hex Wrench
1 pc.
M6x16
Head Cap Bolt
45 pcs. (+1 extra)
Spring Washer
45 pcs. (+1 extra)
Small Hex Wrench
1 pc.
A.
Top
1 pc.
K.
Shelf
1 pc.
N.
Base
1 pc.
L.
Seat
1 pc.
M.
Seat Frame
1 pc.
C.
Side Frame
1 pc.
E.
Back Post
1 pc.
I.
Back Panel
2 pcs.
P.
Side Frame
1 pc.
Q.
Side Frame
1 pc.
R.
Basket
2 pcs.
B.
Side Frame
1 pc.
D.
Back Post
2 pcs.
F.
Rail
1 pc.
G.
Rail
1 pc.
H.
Rail
1 pc.
J.
Rail
2 pcs.
O.
Divider
1 pc. Refer to later page(s) of these
instructions for basket assembly.
M x613
Tapered Bolt (short)
16 pcs. (+1 extra )
M x638
Tapered Bolt (medium)
8 pcs. (+1 extra )
M x670
Tapered Bolt (long)
4 pcs. (+1 extra )
M3x12
Wood Screw
for Hook
8 pcs. (+1 extra)
Flat Washer
45 pcs. (+1 extra)
M3.5x8
Wood Screw
for Back Panel
12 pcs. (+1 extra)
Hook
4 pcs.
Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/8” Drill Bit
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460

Assembly Instructions 2/7
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as the bolts may need to be tightened in the future.
Head Cap Bolt
Spring Washer
Flat Washer
Flat Washer
Spring Washer
Head Cap Bolt
STEP 1
Attach Rails (F) and (G) to Back Posts (D) and (E)
with Flat Washers, Spring Washers and
Head Cap Bolts, tightening bolts
only halfway. (See Figure 1)
Figure 1
STEP 2
Attach unit and Rail (H) to Side Frame (B)
with Flat Washers, Spring Washers and
Head Cap Bolts, tightening bolts only halfway.
(See Figure 2)
Attach Side Frame (C) to unit with Flat Washers,
Spring Washers and Head Cap Bolts,
tightening bolts only halfway.
Figure 2
D
D
E
F
G
C
B
H

Assembly Instructions 3/7
STEP 4
Turn unit to its upright position.
Attach Back Panels (I) to unit by inserting
Wood Screws for Back Panel into pre-drilled holes,
then tighten. (See Figure 3)
STEP 3
Slide Back Panels (I) into position.
Attach Top (A) and Shelf (K) to unit with
Flat Washers, Spring Washers and
Head Cap Bolts, tightening
bolts only halfway.
Tighten all bolts used
in Steps 1, 2 and 3.
Wood Screw for Back Panel
Figure 3
Flat Washer
Spring Washer
Head Cap Bolt
A
K
I
I
II

Assembly Instructions 4/7
STEP 5
Attach Rails (J) and Seat Frame (M) to Side Frame (Q)
with Flat Washers, Spring Washers, Head Cap Bolts and
Tapered Bolts (medium), tightening bolts
only halfway. (See Figure 4)
Attach Side Frame (P) to unit with Flat Washers,
Spring Washers, Head Cap Bolts and
Tapered Bolts (medium), tightening bolts
only halfway.
Tighten all bolts used in this step.
STEP 6
Attach Base (N) to unit with Flat Washers,
Spring Washers and Head Cap Bolts,
tightening bolts only halfway.
Attach Divider (O) to unit with
Tapered Bolts (medium),
tightening bolts
only halfway.
Attach Seat (L) to unit
with Flat Washers, Spring Washers
and Head Cap Bolts, tightening
bolts only halfway.
Tighten all bolts used in this step.
Tapered Bolt (medium)
O
J
J
P
Q
Figure 4
L
N
Flat Washer
Spring Washer
Head Cap Bolt
Tapered Bolt (medium)
Flat Washer
Spring Washer
Head Cap Bolt
P
M
JJ
Q
O

Basket (R)
R2.
Basket Side
4 pcs.
R1.
Basket Unit
2 pcs.
STEP 7
Attach Basket Side (R2) to Basket Unit (R1)
with clips and Tapered Bolts (short). (See Figures 5 and 6)
R1
R2
Tapered Bolt (short)
Clip
Clip
Tapered Bolt (short)
STEP 8
Attach Basket Side (R2) to unit
with clips and Tapered Bolts (short).
R2
Figure 6
Part List
Assembly Instructions 5/7
Figure 5

Assembly Instructions 6/7
STEP 9
Attach unit from Step 4 to unit from Step 6 with Tapered Bolts (long).
Attach Hooks to unit by inserting Wood Screws for Hook into
pre-drilled holes in unit, then tighten. (See Figure 7)
Slide Baskets (R) into position.
Level unit by adjusting the adjustable levelers on bottom of unit.
(See Figure 8)
Note: Unit must be level to work properly.
Figure 7
Figure 8
Wood Screw for Hook
Hook
Tapered Bolt (long)
R
R

Hardware List
Assembly Instructions 7/7
STEP 10
Place unit at desired location.
Drill a 3/8” hole in wall in-line with
the pre-drilled hole at top of unit.
Move unit.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole
at top of unit with Machine Screw.
Move unit back into place.
Slide Tipover Restraint through
Bracket on wall and Bracket on unit.
(See Figure 9)
Put tie end of Tipover Restraint into lock
end of Tipover Restraint and pull until tight.
Anchor
1 pc. (+1 extra)
Bracket
2 pcs. (+1 extra)
Tipover Restraint
1 pc. (+1 extra)
M3.5x40
Wall Screw
1 pc. (+1 extra)
Figure 9
IMPORTANT
To help reduce the risk of the unit tipping over, the Tipover Restraint must be installed following these instructions exactly.
M4x10
Machine Screw
1 pc. (+1 extra)
Machine Screw
Wall Screw
Bracket
on wall
Anchor in wall
3/8” wall hole
Pre-drilled hole
at top of unit
Tie end
Lock end
Bracket at
top of unit
Tipover
Restraint
Drill 3/8” hole in wall
Top of unit

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
homestyles will provide replacements free of charge for missing or damaged parts within 1 year of purchase.
Digital images of the defective parts may be required. If the product was not purchased from an authorized retailer,
homestyles is under no obligation to provide replacement parts. Parts are not available for fully assembled items nor
are parts available for sale. Replacements for missing or damaged parts may be requested via contact info below.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460