Home Styles Naples 5530-940 User manual

Hardware List
Part List
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Tool(s) required for assembly: Phillips screwdriver, Level
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Cartons 88 5530 941, 943 are also needed for assembly.
88 5530 942
Storage Island
B.
Bottom
1 pc.
D.
Back Panel
1 pc.
F.
Shelf
6 pcs.
C.
Plinth
2 pcs.
E.
Back Panel
1 pc.
G.
Front Rail
4 pcs.
M4x28
Machine Screw
20 pcs.
Cam Lock Screw
40 pcs. (+2 extra)
Cam Lock
40 pcs. (+6 extra)
Flat Washer
6 pcs. (+1 extra)
Adjustable Pin
24 pcs. (+1 extra)
M6x35
Bolt
6 pcs. (+1 extra)
M3.5x16
Wood Screw (short)
for Drawer Bottom
60 pcs. (+1 extra)
Knob (small)
8 pcs.
Knob (large)
12 pcs.
M3.5x25
Wood Screw (long)
for Drawer Side
80 pcs. (+1 extra)
M3x25
Wood Screw for
Side Panels
4 pcs. (+1 extra)

Assembly Instructions 2/7
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the screws until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
STEP 1
Insert Cam Lock Screws into
pre-drilled holes of Top (A),
Plinths (C), Side Panels (H), (I)
and Middle Panel (J).
(See Figure 1)
Cam Lock Screw
Cam Lock Screw
Cam Lock Screw
Figure 1
C
C
HI
J
Cam Lock Screw
A

STEP 3
Attach Bottom (B) to unit
with Flat Washers and Bolts.
(See Figure 3)
Flat Washer
Bolt
STEP 2
Attach Back Panels (D) and (E) to
Middle Panel (J) with Cam Locks.
(See Figure 2)
Attach Front Rails (G) to unit.
Cam Lock
Assembly Instructions 3/7
Figure 2
Figure 3
D
E
G
G
G
G
B
J

STEP 5
Attach Side Panels (H) and (I)
to unit with Cam Locks and
Wood Screws for Side Panel.
STEP 4
Attach Plinths (C) to unit
with Cam Locks.
Attach Leg Support (K) to unit.
Cam Lock
Cam Lock Wood Screw
for Side Panel
Wood Screw
for Side Panel
Assembly Instructions 4/7
C
K
I
H
C

STEP 6
Attach Top (A) to unit
with Cam Locks.
Level unit by adjusting the adjustable
levelers on the bottom of unit. (See Figure 4)
Note: Unit must be level to work properly.
STEP 7
Insert Adjustable Pins into side panels
and middle panel at desired level, then
place Shelves (F) into position.
STEP 8
Slide Drawers (L) and (M) into position.
Adjustable Pin
Assembly Instructions 5/7
A
F
F
F
F
F
F
Figure 4
L
M
L
M
M
L
M
L
M
M
Cam Lock