Home Styles 5180-15 User manual

Hardware List
Part List
Tool(s) required for assembly: Phillips screwdriver, Level
5180-15
Executive Desk
IMPORTANT
Refer to later page(s) of these
instructions for drawer assembly.
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Hex Wrench
1 pc.
Small Hex Wrench
1 pc.
Cam Lock Screw
8 pcs. (+1 extra)
Cam Lock
8 pcs. (+4 extra)
M3x32
Wood Screw (long)
6 pcs. (+1 extra)
M3x16
Wood Screw (short)
8 pcs. (+1 extra)
M3x10
Wood Screw for Hinge
6 pcs. (+1 extra)
M6x32
Head Cap Bolt
21 pcs. (+1 extra)
M4x38
Machine Screw
4 pcs.
A.
Top
1 pc.
B.
Side Frame
1 pc.
C.
Side Frame
1 pc.
D.
Front Frame
1 pc.
E.
Front Frame
1 pc.
J.
Stretcher
1 pc.
L.
Keyboard
1 pc.
K.
Keyboard
1 pc.
M.
Drawer
2 pcs.
F.
Front Rail
1 pc.
G.
Back Panel
1 pc.
I.
Divider
1 pc.
H.
Divider
1 pc.
Knob
4 pcs.
M3x25
Wood Screw
16 pcs. (+1 extra)
Flat Washer
21 pcs. (+1 extra)
Spring Washer
21 pcs. (+1 extra)
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460

Assembly Instructions 2/6
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as bolts may need to be tightened in the future.
Cam Lock Screw
G
STEP 1
Insert Cam Lock Screws into pre-drilled holes in Front Frames (D), (E) and Back Panel (G),
then tighten. (See Figure 1)
STEP 2
Attach Front Frames (D) and (E) to Front Rail (F) with Wood Screws (long).
(See Figure 2)
Figure 2
Wood Screw (long)
Figure 1
D
E
D
E
F

STEP 3
Attach Dividers (H) and (I) to unit with Cam Locks.
(See Figure 3)
Attach Back Panel (G) to unit with Cam Locks.
Cam Lock
Figure 3
Assembly Instructions /36
STEP 4
Attach Side Frame (B) to unit with
Flat Washers, Spring Washers and Head Cap Bolts. (See Figure 4)
Attach Stretcher (J) to unit with Wood Screw (long). (See Figure 5)
Attach Side Frame (C) to unit with Flat Washers, Spring Washers, Head Cap Bolts
and Wood Screw (long).
Wood Screw (long)
Flat Washer
Spring Washer
Head Cap Bolt
G
I
H
Figure 5
Figure 4
J
B
C

Assembly Instructions /46
Head Cap Bolt
Spring Washer
Flat Washer
Head Cap Bolt
Spring Washer
Flat Washer
STEP 5
Place Top (A) upside down on a soft cloth.
Attach unit to Top (A) with Flat Washers, Spring Washers and Head Cap Bolts.
STEP 6
Insert Flat Washers, Spring Washers and Head Cap Bolts into pre-drilled holes, then tighten.
A

Part List
Assembly Instructions /56
STEP 9
Attach Knob with Machine Screw.
M5.
Drawer Bottom
2 pcs.
M1.
Drawer Front
2 pcs.
M2.
Drawer Back
2 pcs.
M3.
Drawer Side
2 pcs.
M4.
Drawer Side
2 pcs.
Knob
STEP 8
Slide Drawer Bottom (M5) into groove.
Attach Drawer Bottom (M5) to unit with
Wood Screws (short).
Machine Screw
Drawer (M)
STEP 7
Attach Drawer Front (M1) and Drawer
Back (M2) to Drawer Side (M3) with
Wood Screws.
Attach Drawer Side (M4) to unit with
Wood Screws.
Roller at back
Bottom
Wood Screw
Wood Screw (short)
M1
M3
M4
M2
M5

Assembly Instructions /66
STEP 10
Attach Keyboard (L) to Keyboard (K)
with Wood Screws for Hinge.
Attach Knobs to keyboard
with Machine Screws.
(See Figure 6)
Wood Screw for Hinge
Figure 6
Keyboard
STEP 11
Turn unit over to its upright position.
Slide keyboard and Drawers (M) into position.
Level unit by adjusting the adjustable levelers on bottom of unit.
(See Figure 7)
Note: Unit must be level to work properly. Figure 7
MM
K
L
Machine Screw
Knob

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
homestyles will provide replacements free of charge for missing or damaged parts within 30 days of purchase.
Digital images of the defective parts may be required. If the product was not purchased from an authorized retailer,
homestyles is under no obligation to provide replacement parts. Parts are not available for fully assembled items nor
are parts available for sale. Replacements for missing or damaged parts may be requested via contact info below.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460