Homelegance Norman 2514BK-36 User manual

1
ASSEMBLY INSTRUCTIONS
ITEM: 2514BK-36
5pcs Pack Counter Height Set
Black Finish
This page lists all the contents included in the box. Please take time to identify the
hardware as well as the individual components to this product. As you unpack and
prepare for assembly, place the contents on a carpeted or padded area to protect
them from damage.
c l e a n i n g & c a r e Treat surface with care. Clean surfaces with a dry or
damp soft cloth. Do not use abrasive cleaners. Hardware may loosen over time.
Periodically check that all connections are tight.
A Phillips head screwdriver is necessary for assembly.

2

Attach table shelf (C) to the table legs (B) using Allen bolts (1), spring
washers (2) and flat washers (3) as shown. Don't tighten all Allen bolts
at this step.
STEP 1
3
Attach table legs (B) to the table shelf (C) using Allen bolts (1), spring
washers (2) and flat washers (3) as shown. Don't tighten all Allen bolts
at this step
.
STEP 2
REQUIRED HARDWARE IN THIS STEP
NO. DESCRIPTION SKETCH QTY
2.
4 PCS
SPRING WASHER
1.
4 PCS
3.
4 PCS
ALLEN WRENCH
4. 1 PC
FLAT WASHER
ALLEN BOLT
10. 2 PCS
LEVELER
Attach levelers (10) into the pre-drilled holes on the bottom of the
legs (B).
REQUIRED HARDWARE IN THIS STEP
NO. DESCRIPTION SKETCH QTY
2.
4 PCS
SPRING WASHER
1.
4 PCS
3.
4 PCS
ALLEN WRENCH
4. 1 PC
FLAT WASHER
ALLEN BOLT
10. 2 PCS
LEVELER
Attach levelers (10) into the pre-drilled holes on the bottom of the
legs (B).

4
Turn the assembly upright. Place table top (A) down to the
assembly unit as shown, making sure table legs secure into top
.
Attach table legs (B) to table top (A) using Allen bolt (1), spring washer
(2) and flat washer (3) as shown.
STEP 3
STEP 4
REQUIRED HARDWARE IN THIS STEP
NO. DESCRIPTION SKETCH QTY
2.
4 PCS
SPRING WASHER
1.
4 PCS
3.
4 PCS
ALLEN WRENCH
4. 1 PC
FLAT WASHER
ALLEN BOLT
Make sure the table is level, and tighten all Allen bolt (1) by Allen wrench.

5
STEP5
Turn the table upright.
The table is now ready for use

Attach seat frame (F) to chair back frame (D) using short bolts (6), long
bolts (5), spring washers (2) and flat washers (3) as shown. do not tighten
the bolts in this step.
6
REQUIRED HARDWARE IN THIS STEP
NO. DESCRIPTION SKETCH QTY
2.
7 PCS
SPRING WASHER
7 PCS
3.
OPEN WRENCH
9. 1 PC
FLAT WASHER
LONG BOLT
5. 4 PCS
SHORT BOLT
6. 3 PCS
Note: Seat frame (F) has holes on each side. These holes are to attach
the seat board (E) in the next step. Ensure that the wider end of the holes
face down towards the ground.
Place seat board (E) upside down on a clean smooth surface. Attach
assembled chair frame to the seat board (E) with wood screw (7) using
a Phillips head screw driver (not included).
REQUIRED HARDWARE IN THIS STEP
NO. DESCRIPTION SKETCH QTY
7. WOOD SCREW
6 PCS
STEP 6
STEP 7

STEP 8
7
Attach chair left and right front legs (G & H) to seat frame (F) with flat
washers (3), spring washers (2), and nuts (8) as shown. Do not fully tighten
nuts (8). Insert chair left side crossbar and chair right side crossbar (J)
into the front left and right chair legs (G & H) and chair back frame (D).
Note: The small holes on all the crossbars must face towards the ground
(when chair in the normal use position).
Tighten all nuts previously installed with wrench (9). Secure the front
crossbar (I), chair left side crossbar (J) and chair right side crossbar (J) to
the chair legs using wood screws(7) and a Phillips head screw driver
(not included) as shown below.
REQUIRED HARDWARE IN THIS STEP
NO. DESCRIPTION SKETCH QTY
2.
4 PCS
SPRING WASHER
8.
4 PCS
3.
4 PCS
OPEN WRENCH
9. 1 PC
FLAT WASHER
NUT
7. WOOD SCREW 6 PCS

Repeat Step 6-8 to assemble the remaining chairs.
STEP 9
8
Turn the chair upright.
The chair is now ready for use