Honeywell IS3016A User manual

IS3016A Passive Infrared Motion Sensor with Anti-Mask -Installation Instructions
QUICK LINKS
Mounting Location Guidelines
Open the Sensor
Mount the Sensor
Sensor Components and Settings
Wire the Sensor
Wiring Examples
Walk Test the Sensor
Detection Patterns
Remote LED Enable
Relay Operation
Mask Condition
Troubleshooting
Sensor Specifications
Accessories
Approval Listings
1. Turn the arrow to point to the Unlock symbol.
2. Press firmly on housing latch.
3. Gently separate the front and rear housing.
[EN] = approved installation.
Mounting location guidelines:
•The maximum range is obtained at a mounting height
of 2.3m (7’ 6”).
•Allow a clear line-of-sight to all areas to protect.
•Avoid mounting anything within 30cm (12”) in front of the sensor.
•Do not directly face windows.
•Avoid close proximity to moving machinery, fluorescent lights, and
heating/cooling sources.
•Not for use in applications with pets.

- 2 -
•[A]= Wall mounting holes.
•[B] = Corner mounting holes.
•The rear tamper plate MUST be
mounted to a stud, solid wood, or with
a robust wall anchor.
See wiring
details and
examples on
page 3.

- 3 -
WIRING DETAILS
-Observe proper polarity.
-If not using the integrated EOL resistors, set all switches to
OFF.
-If using the integrated EOL resistors:
1.Connect the sensor to the panel (see wiring diagrams
below).
2.Set the appropriate tamper, alarm and Anti-mask/ [RF]
DIP switches to ON (see Step 4 on page 2).
Notes:
-Consult the Control Panel manual to determine proper
EOL selection.
-The Alarm, Tamper and Trouble/anti-mask EOL
settings must each only have one switch ON.
-The EOL values should be set at the same time.
Wiring Examples
Alarm, Tamper and
Trouble/Anti-Mask
configured to one
loop.
Alarm, Tamper and
Trouble/Anti-Mask
configured to two
loops.
1. Close the sensor and apply power to the sensor. Initialization is
complete when the LED stops flashing slowly (about 20 seconds).
2. Walk through the detection area and observe the LED.
Walk test mode is active for 10 minutes, then automatically exits test mode,
disables the LED and enters normal operation mode. For an additional 10 minute
walk test, enable Walk Test mode again with the Flashlight feature (see the
following page.
RA = Alarm EOL resistor
RF = Anti-Mask EOL resistor
RT = Tamper EOL resistor
W1 = 1 and 2 loop connection resistor.
Note: During power up and walk
test modes the LED is active
regardless of the LED
Enable/Disable DIP switch setting.
LED Power
Up
Walk Test
[10 min.] Normal
Trouble
Fault
Anti-Mask
Red Slow
Blink
ON
Alarm
ON
Alarm
Fast
Blink OFF
Yellow OFF OFF OFF OFF Fast
Blink

- 4 -
Flashlight Feature:
1. Use a flashlight with a bright light beam, and stand within 1.2 m (4’) of the
sensor.
2. Swing past the lights beam across the sensor IR window 3-5 times, holding
the beam on the window for 0.5 second each pass.
The flashlight feature is only available for the first 24 hours after the first power up.
REMOTE LED ENABLE (LED INPUT)
The LED input terminal allows the LED to be
remotely enabled. To use this feature, the
LED DIP switch (switch 2) must be OFF,
allowing the LED to operate based on the voltage level
connected to the LED Input (see Wiring Details).
Switch 2
LED Input
LED Operation
OFF
High ( +12 V)
Enabled
OFF
Low (0 V)
Disabled
ON Low (0 V) or High (+12 V) Enabled
RELAY OPERATION
SENSOR STATUS
Normal
Intrusion
Trouble1
Mask2
Alarm Relay
Closed
Open
Closed
Open
Trouble Relay 3
Closed
Closed
Open
Open
1 For information on Trouble conditions, see the Troubleshooting section.
2 In a Mask condition, the Alarm and Trouble relays will activate simultaneously,
and remain open until the condition has been cleared.
3 In a Trouble condition, the Trouble relay will latch open until the Trouble
condition has been cleared.
MASK CONDITION
Normal Anti-Mask Condition
The sensor uses Active Infrared (AIR) technology to detect
masking. The sensor signals a mask condition when a variety
of materials and reflective objects are placed within 50mm (2
inches) in front of the sensor. To avoid false mask alarms,
follow the mounting guidelines shown in Step 1.
Clearing an Anti-Mask Condition
When most masking materials or objects are removed, the
anti-mask condition will be cleared after several seconds.
When the cause of the anti-mask condition is any type of spray
or paint coating applied to the window, the window must be
replaced before the anti-mask condition can be cleared. After
replacing the window, perform a walk test on the sensor.
TROUBLESHOOTING
TROUBLE*
NORMAL
Mask1
Low
Voltage
2
Self-Test
Failure
3
Alarm Relay
Closed
Open
Closed
Closed
Trouble Relay
Closed
Open
Open
Open
Red LED
Off Off Off Flashing
Yellow LED
Off
Flashing
Off
Off
*TROUBLE CONDITIONS:
1Mask condition: Sensor IR window is blocked or masked.
2Low Voltage: The sensor is disabled. [Note: If voltage drops below 5V, both
Alarm and Trouble relays open.]
3Self-Test Failure conditions:
•PIR self-test failure: The sensor is disabled.
•Temperature compensation failure: The temperature compensation is
disabled.
Depending on the Trouble condition, take the following corrective actions:
•Verify the sensor is not blocked or masked.
•Verify the power supply is sufficient (at least 9V at the sensor).
•Cycle power to the sensor.
•Walk test the sensor.
If the Trouble condition does not clear, replace the sensor.
Zones
A
2Look-down
B
12
Lower
C
10
Intermediate
D
36
Long

- 5 -
SPECIFICATIONS
Range: 16 m x 22 m
Power: 9.0 - 15 VDC; 9 mA typical, 11 mA maximum, 12 VDC;
AC Ripple: 3 V peak-to-peak at nominal 12 VDC
Alarm Relay: Energized Form A; 30 mA, 25 VDC, 22 Ohms
resistance maximum. Alarm Relay Duration: 3 seconds
Trouble Relay: Energized Form B; (NC) 30 mA, 25 VDC; 22 Ohms
resistance maximum
Tampers: Cover & Wall; (NC with cover installed) Form A;
30 mA, 25 VDC; Magnetic field
RFI Immunity: 15 V/m, 80 MHz – 2.7 GHz
PIR White Light Immunity: 10,000 Lux typical
Fluorescent light filter: 50 Hz / 60 Hz.
Operating Temperature: -10° to 55° C
Relative Humidity: 5 to 95%; non-condensing
Temperature Compensation: Advanced Dual Slope
Dimensions: 11.6 cm H x 7.0 cm W x 4.3 cm D
Weight: 118 g (net weight)
ACCESSORIES
SMB-10
(P/N 0-000-110-01) Swivel Mount Bracket
SMB-10C
(P/N 0-000-111-01) Swivel Mount Ceiling Bracket
SMB-10T
(P/N 0-000-155-01) Swivel Mount Bracket w/Tamper
Note: The accessories are not covered by certifications.
APPROVAL LISTINGS
EN50131-2-2:2008, Security Grade 3,
Environmental Class II.
Suitable for connection to an EN 60950
Class II Limited Power Source.
PD6662:2010
Note: In EN 50131-2-2 compliant installations, mount the sensor at 2.3m,
do not use o
nly the right side corner mounting holes, enable look down
and lock the sensor housing with the cover lock (see “[EN]” where
noted in Steps 1-4).
Important: The sensor should be tested at least once each year.
NF&A2P 3 boucliers (référentiel
NF324-H58) et conforme aux normes
EN50131-2-2 et RTC50131-2-2
IP30 IK04
N° de certificat: 2631420016
Organisme de certification:
CNPP Cert. : www.cnpp.com et
AFNOR Cert.: www.marque-nf.com
Honeywell Security Group - BP1219
1198 avenue du docteur Maurice Donat
Sophia Antipolis
06254 Mougins Cedex.
TEL: [phone]
FAX: [phone]
INCERT: B-893-0013
Corrente
norminale:
12 =
Corrente
massima
assorbita:
11 mA
LARMKLASS
4

For any additional information, please refer to our Website:
http://www.honeywell.com/security/emea/hscdownload
Or contact:
Honeywell Security Group
Newhouse Industrial Estate
Motherwell
Lanarkshire ML1 5SB
United Kingdom
Please contact your local authorised Honeywell representative for product warranty information.
2013 Honeywell International Inc. Honeywell and DUAL TEC are registered trademarks of Honeywell International Inc.
All other trademarks are the properties of their respective owners. All rights reserved. Made in China.
P/N 800-15672 Rev B
Tel: [phone]
Email: [e-mail]
www.honeywell.com/security