Honeywell IS3016 User manual

IS3016 Passive Infrared Motion Sensor – Installation Instructions
QUICK LINKS
Mounting Location Guidelines
Open the Sensor
Mount the Sensor
Sensor Components and Settings
Wire the Sensor
Wiring Example
Walk Test the Sensor
Detection Patterns
Relay Operation
Troubleshooting
Sensor Specifications
Accessories
Approval Listings
Mounting location guidelines:
•The maximum range is obtained at a mounting height
of 2.3m (7’ 6”).
•Allow a clear line-of-sight to all areas to protect.
•Do not directly face windows.
•Avoid close proximity to moving machinery, fluorescent lights, and
heating/cooling sources.
•Not for use in applications with pets.
1. Turn the arrow to point to the Unlock symbol.
2. Press firmly on housing latch.
3. Gently separate the front and rear housing.
[EN] = approved installation.

- 2 -
See wiring details and
examples on page 3.

- 3 -
WIRING DETAILS
-Observe proper polarity.
-If not using the integrated EOL resistors, set all switches to OFF.
-If using the integrated EOL resistors:
1.Connect the sensor to the panel (see wiring diagrams below).
2.Set the appropriate tamper, alarm and tamper DIP switches
to ON (see Step 4 on page 2).
Notes:
-Consult the Control Panel manual to determine
proper EOL selection.
-The Alarm and Tamper EOL settings must each
only have one switch ON.
-The EOL values should be set at the same time.
Wiring Example
Alarm and Tamper
configured to one
loop.
Flashlight Feature:
1. Use a flashlight with a bright light beam, and stand within 1.2 m (4’) of the
sensor.
2. Swing the light beam past the sensor IR window 3-5 times, holding the
beam on the window for 0.5 second each pass.
The flashlight feature is only available for the first 24 hours after the first
power up.
1. Close the sensor and apply power to the sensor. Initialization is complete when the LED stops flashing slowly
(about 20 seconds).
2. Walk through the detection area and observe the LED.
Walk test mode is active for 10 minutes, then automatically exits test mode, disables the LED and enters normal
operation mode. For an additional 10 minute walk test, enable walk test mode again with the flashlight feature.
Note: During power up and walk test modes the LED is active regardless of the LED Enable/Disable DIP switch setting.
RA = Alarm EOL resistor
RT = Tamper EOL resistor
LED Power
Up
Walk Test
[10 min.] Normal Trouble
Red Slow
Blink
ON
Alarm
ON
Alarm
Fast
Blink

RELAY OPERATION
SENSOR STATUS
Normal
Intrusion
Trouble1
Alarm Relay
Closed
Open
Open
1 For information on Trouble conditions, see the Troubleshooting section.
TROUBLESHOOTING
TROUBLE*
NORMAL
Self-Test Failure1
Alarm Relay
Closed
Open
Red LED
Off
Flashing
*TROUBLE CONDITIONS:
1Self-Test Failure conditions:
•PIR self-test failure: The sensor is disabled.
•Temperature compensation failure: The temperature compensation is
disabled.
Depending on the Trouble condition, take the following corrective actions:
•Verify the power supply is sufficient (at least 9V at the sensor).
•Cycle power to the sensor.
•Walk test the sensor.
If the Trouble condition does not clear, replace the sensor.
SPECIFICATIONS
Range: 16 m x 22 m
Power: 9.0 - 15 VDC; 7 mA typical, 11 mA maximum, 12 VDC;
AC Ripple: 3 V peak-to-peak at nominal 12 VDC
Alarm Relay: Energized Form A; 30 mA, 25 VDC, 22 Ohms resistance
maximum. Alarm Relay Duration: 3 seconds
Trouble Relay: Energized Form B; (NC) 30 mA, 25 VDC; 22 Ohms
resistance maximum
Tampers: Cover; (NC with cover installed) Form A;
30 mA, 25 VDC; Magnetic field
RFI Immunity: 15 V/m, 80 MHz – 2.7 GHz
PIR White Light Immunity:10,000 Lux typical
Fluorescent light filter: 50 Hz / 60 Hz.
Operating Temperature:-10° to 55° C
Relative Humidity: 5 to 95%; non-condensing
Temperature Compensation: Advanced Dual Slope
Dimensions: 9.8 cm H x 5.7 cm W x 4.35 cm D
Weight: 80 g (net weight)
ACCESSORIES
SMB-10
(P/N 0-000-110-01) Swivel Mount Bracket
SMB-10C
(P/N 0-000-111-01) Swivel Mount Ceiling Bracket
SMB-10T
(P/N 0-000-155-01) Swivel Mount Bracket w/Tamper
Note : The accessories are not covered by certifications.
APPROVAL LISTINGS
EN50131-2-2:2008, Security Grade 2,
Environmental Class II.
Suitable for connection to an EN 60950 Class II
Limited Power Source.
Note: In EN 50131-2-2 compliant installations, mount the sensor at 2.3m,
enable look down and lock the sensor housing with the cover lock (see
“[EN]” where noted in Steps 1-4).
IMPORTANT: The sensor should be tested at least once each year.
NF&A2P 2 boucliers (référentiel NF324-H58)
et conforme aux normes EN50131-2-2 et
RTC50131-2-2; IP30 IK04
N° de certificat: 2821420019
Organisme de certification:
CNPP Cert. : www.cnpp.com et
AFNOR Cert.: www.marque-nf.com
PD6662:2010
Honeywell Security Group - BP1219
1198 avenue du docteur Maurice Donat
Sophia Antipolis
06254 Mougins Cedex
TEL: [phone]
FAX: [phone]
INCERT B-893-0015
LARMKLASS 2
Corrente norminale: 12 =
Corrente massima
assorbita: 11 mA
For any additional information, please refer to our Website:
http://www.honeywell.com/security/emea/hscdownload
Or contact:
Honeywell Security Group
Newhouse Industrial Estate
Motherwell
Lanarkshire ML1 5SB
United Kingdom
Please contact your local authorised Honeywell representative for
product warranty information.
2013 Honeywell International Inc. Honeywell and DUAL TEC are registered trademarks of Honeywell International Inc.
All other trademarks are the properties of their respective owners. All rights reserved.
Zones
A
2Look-down
B
18 Lower
C
20
Intermediate
D
54
Long
Tel: [phone]
Email: [e-mail]
P/N 800-16904 Rev A
www.honeywell.com/security