Honeywell SS500 Series User manual

Installation Instructions for the ISSUE 5
SS500 Series Temperature Compensated
Hall Effect Sensors
PK 80079
WARNING
PERSONAL INJURY
DO NOT USE these products as safety or
emergency stop devices or in any other application
where failure of the product could result in personal
injury.
Failure to comply with these instructions could
result in death or serious injury.
CAUTION
ELECTROSTATIC DISCHARGE DAMAGE
This component is sensitive to electrostatic discharge
(ESD). Take normal ESD precautions in handling this
product to prevent ESD-induced damage and/or
degradation.
Failure to comply with these instructions will
result in product damage.
CAUTION
WAVE SOLDER DAMAGE
DO NOT wave solder this product. Wave soldering
may negatively affect the sensor performance and
reliability. Subjecting the sensor to wave soldering
will void Honeywell’s warranty.
Failure to comply with these instructions will
result in product damage.
ABSOLUTE MAXIMUM RATINGS*
Supply Voltage -1 to +30 VDC
Voltage externally
applied to output
+30 VDC max. (OFF only)
-0.5 VDC min. (OFF or ON)
Output ON Current See Table A.
Operating Temperature -50 to +160°C
(-67 to +320°F)
Storage Temperature -65 to +160°C
(-85 to +320°F)
Magnetic Flux No limit. Circuit cannot be
damaged by magnetic
overdrive.
* Absolute maximum ratings are the extreme limits that the
device will withstand without damage to the device.
However, the electrical and mechanical characteristics are
not guaranteed as the maximum limits (above
recommended operating conditions) are approached, nor
will the device necessarily operate at absolute maximum
ratings.
SOLDERING INSTRUCTIONS
Honeywell recommends an infrared reflow process
with peak temperatures not to exceed 245°C (473°F)
for 10 seconds maximum.
BLOCK DIAGRAM
TRIGGER
CIRCUIT
AND
AMPLIFIER
SENSOR
HALL
GROUND (-)
Vs (+)
OUTPUT
(0) N.H.
OPERATING CHARACTERISTICS (over Operating Voltage and Temperature, unless otherwise noted)
Min. Typ. Max. Remarks TABLE A
Supply Voltage 3.8 ⎯30 VDC
Output Current
Absolute Limits
Current Consumption ⎯⎯10 mA
Supply
Voltage
Output
Current
Max. mA
Output Voltage (operated) ⎯0.15 0.40 Sinking 20 mA max. -1 to 24 50
Output Current (operated) ⎯⎯20 mA 24 to 25 37
Output Leakage Current (released) ⎯⎯10 µA 25 to 26 33
Output Switching Time VCC = 12 V, 26 to 27 28
Rise, 10 to 90% ⎯.05 µs 1.5 µs RL= 1.6 K Ω, 28 to 29 19
Fall, 90 to 10% ⎯.15 µs 1.5 µs CL= 20 pF 29 to 30 15
Operating Temperature Range -40°C to +125°C (-40°F to 302°F)
Note: To prevent damage to the leads, SS500 Series surface mounted sensors are
supplied only on tape and reel.
Sensing and Control

SS500 Series ISSUE 5 PK 80079
MAGNETIC CHARACTERISTICS
SS511AT SS513AT SS541AT SS543AT SS549AT SS561AT SS566AT
Magnetic Type Bipolar Bipolar Unipolar Unipolar Unipolar Latching Latching
-40°C Max. Op. 70 140 135 215 435 110 200
Min. Rel. -70 -140 20 80 210 -110 -200
Min. Dif. 15 20 15 25 30 50 200
0°C Max. Op. 65 140 117 190 400 90 185
Min. Rel. -65 -140 20 80 230 -90 -185
Min. Dif. 15 20 15 25 30 50 200
25°C Max. Op. 60 140 115 180 390 85 180
Min. Rel. -60 -140 20 75 235 -85 -180
Min. Dif. 15 20 20 25 30 50 200
85°C Max. Op. 60 140 120 180 400 85 180
Min. Rel. -60 -140 15 70 215 -85 -180
Min. Dif. 12 20 15 15 30 50 190
125°C Max. Op. 65 140 123 190 410 100 180
Min. Rel. -65 -140 15 60 200 -100 -180
Min. Dif. 12 20 8 10 30 50 160
150°C Max. Op. 70 140 125 200 420 110 185
Min. Rel. -70 -140 10 55 185 -110 -185
Min. Dif. 10 20 5 5 30 50 140
NOTICE
Bipolar Hall effect sensors may have an initial output in either the On or Off state if powered up with an
applied magnetic field in the differential zone (applied magnetic field > Brp and < Bop). Honeywell
recommends allowing 10 µsec for output voltage to stabilize after supply voltage has reached 5 volts.
INTERFACE DIAGRAMS
2 Honeywell •Sensing and Control For application help: call 1-800-537-6945

SS500 Series ISSUE 5 PK 80079
MOUNTING DIMENSIONS (for reference only) mm/in
TAPE DIMENSIONS
(for reference only) mm/in
NOTE: This product is sold in tape and reel form
only, per EIA STD 481. There are 1,000 parts per
reel.
REEL DIMENSIONS
(for reference only) mm/in
For application help: call 1-800-537-6945 Honeywell •Sensing and Control 3

SS500 Series ISSUE 5 PK 80079
Sensing and Control
www.honeywell.com/sensing
Honeywell
11 West Spring Street
Freeport, Illinois 61032
80079-5-EN IL50 GLO 104 Printed in USA
Copyright 2004 Honeywell International Inc. All Rights Reserved.
WARRANTY/REMEDY
Honeywell warrants goods of its manufacture as
being free of defective materials and faulty
workmanship. Contact your local sales office for
warranty information. If warranted goods are
returned to Honeywell during the period of
coverage, Honeywell will repair or replace without
charge those items it finds defective. The
foregoing is Buyer’s sole remedy and is in lieu
of all other warranties, expressed or implied,
including those of merchantability and fitness
for a particular purpose.
Specifications may change without notice. The
information we supply is believed to be accurate
and reliable as of this printing. However, we assume
no responsibility for its use.
While we provide application assistance
personally, through our literature and the Honeywell
web site, it is up to the customer to determine the
suitability of the product in the application.
For application assistance, current specifications
or name of the nearest Authorized Distributor,
contact a nearby sales office. Or call:
1-800-537-6945 USA/Canada
1-815-235-6847 International
FAX
1-815-235-6545 USA
INTERNET
www.honeywell.com/sensing
[email protected]om