Honeywell ES800 User manual

Portable Evaporative Air Cooler
User Manual
Read and save these instructions before use
www.honeywellhomecomfort.com
E-mail: [e-mail]
Model: ES800

1
PARTS DESCRIPTION
EN
1) Remote Control 7) Detachable Water Tank
2) Remote Control Receptor 8) Castors
3) Control Panel 9) Rear Grill
4) Handle 10) Power Cord Inlet
5) Louvers 11) Power Adapter & Cord
6) Water Level Indicator
with Light
1
5
6
2
7
9
3
4
10
11
8
WARNING -- READ AND SAVE THE AIR COOLER SAFETY & MAINTENANCE GUIDE AND USER
MANUAL BEFORE USING THIS PRODUCT. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY
DAMAGE AND/ OR IMPAIR ITS OPERATION AND VOID THE WARRANTY. IN CASE THERE IS
ANY INCONSISTENCY OR CONFLICT BETWEEN THE ENGLISH VERSION AND ANY OTHER
LANGUAGE VERSION OF THE CONTENT OF THIS MATERIAL, THE ENGLISH VERSION SHALL
PREVAIL.

2
USE & OPERATION
EN
Icons on Display Screen
CONTROL PANEL
Cool Swing
Power ON/OFF
TurboBlast
QuietSleep
Speed
Low Water Alarm
Timer

3
USE & OPERATION (CONTINUED)
EN
POWER
Connect the power adapter to the cooler and to the electrical outlet. Press the button to turn the
unit on. The cooler will start automatically at low speed. To turn the unit off, press the button again.
COOL
Press the button to select Cool mode.
Please make sure the water tank is filled with water above the minimum level mark. Pressing the
COOL indicator light on the display screen activates evaporative cooling. The water pump will
operate and you will feel the cooler air after the Honeycomb Cooling Media is completely wet.
Note: When the cooling function is switched OFF, the unit can still function in a fan only mode
(without evaporative cooling).
FUNCTION BUTTONS
SPEED
Press the button repeatedly to change the fan speed between - - - .
The indicator light will show the selected speed:
QUIETSLEEP/ TURBOBLAST
Press the button to select either QuietSleep or TurboBlast modes. QuietSleep mode minimizes wind
speed for lower airflow. TurboBlast mode blasts wind at high speed for stronger airflow.
SWING
Press the button until the SWING indicator light is illuminated on
the display screen. The louvers will begin to move left to right automatically.
TIMER
Press the button until the desired time duration setting is selected. When the set time has passed,
the unit will automatically turn off (unit remains in Standby mode until power cord is unplugged from
electrical socket). The TIMER function allows you to program the unit for up to 7.5 hours of use.
When AUTO is selected, the wind speed will gradually decrease and increase between the TurboBlast
and QuietSleep fan speeds.
(Low) (Medium) (High) (Auto)
/
LOUVER
MOVEMENT

4
USE & OPERATION (CONTINUED)
EN
REMOTE CONTROL
COOLER LOCATION
NOTE:
•
•
•
•
•
•
•
•
•
•
The remote control requires a CR2025 (1 x 3V) coin type or equivalent battery for replacement.
Open the battery compartment at the back of the remote control and insert the battery inside.
Care must be taken to insert the batteries according to the correct polarity (+ / –) markings
shown inside the battery compartment.
Always point the remote control signal transmitter towards the unit when operating. Make sure
that the signal path is not obstructed.
Remove the batteries if the unit is not going to be used for an extended period of time.
Do not drop the remote control.
Do not mix different types of batteries such as alkaline, carbon-zinc, or rechargeable batteries.
Do not mix old and new batteries.
Do not recharge the battery.
Exhausted batteries are to be removed from the product and safely disposed of as per local
regulations.
Do not dispose of batteries in fire. Batteries may explode or leak.
WARNING: Caution for ingestion of the small battery. Keep away from children and animals.
POWER :
:
:
:
:
:
ON / OFF
Low / Medium / High / Auto
Controls the motion of the louvers
Evaporative cooling on/off
Controls the Timer function for automatic off
QuietSleep / TurboBlast mode
FAN SPEED
SWING
TIMER
QuietSleep/
TurboBlast
COOL
/
Make sure to position the air cooler correctly before you set up and start using the product. Please
refer to the COOLER LOCATION section of the separate Safety & Maintenance Guide.

5
USE & OPERATION (CONTINUED)
EN
CAUTION:
Remove the power adapter and cord from the unit and the electrical outlet before emptying or
refilling the water tank. Wait for 2 minutes before removing the Water Tank to allow any excess water
in the Honeycomb Cooling Media to drip into the tank before removing it.
Note: After removing the tank, water from the Honeycomb may continue to drip and collect in the
tank compartment. Simply wipe dry with a clean, dry cloth.
Slide out the Water Tank. Refill the tank when water level is low. Do not fill
water above the "Max." water level mark to avoid water droplets collecting
on the louvers. Check the water level in the tank before running the
COOL function. The Low Water Alarm will sound when water is low.
Running the unit in COOL mode with inadequate water may cause pump
failure.
If ice is available, you may add ice in the top ice compartment to enhance
the cooling performance.
Note: The water capacity refers to the total volume of water that can be
contained within the air cooler water tank and water distribution system.
The water capacity in the tank at the “Max.” indicator level may be lower
than the actual water capacity of the air cooler.
WATER FILTER*
Some models are equipped with a water filter in the tank, which helps to
filter dust, hair and other particles from entering the water tank. Simply
pour water over the filter when refilling the tank.
To clean the water filter, simply push the bottom of the filter cup upwards
to release from the filter frame. Remove dust and hair from the filter
sponge and rinse under clean water. When clean, replace the sponge
and secure the filter cup back into the frame.
*Applicable for models with water filter feature only.
FILLING WITH WATER & ICE
Front water fill door
for easy tank refill
Ice Compartment
WARNING: Do not fill water tank with dirty water or salt water. This can damage the unit and
Honeycomb media.
Filter Cup
Water
Filter

6
AUTOOFF SAFETY SYSTEM
This unit is equipped with an AutoOff Safety System. When the water tank is detached from the unit
or if the tank is incorrectly positioned, the air cooler will turn off automatically. To restart the cooler,
the tank must be attached to the unit correctly.
USE & OPERATION (CONTINUED)
EN
When the unit turns on, the water level indicator located at the front of the water tank will light up
to produce an elegant glow. This can be convenient as a night light during the night. This light will
remain on for as long as the air cooler is turned on.
The unit is equipped with a low water sensor. In Cooling Mode, when water in the tank is below the
minimum level, you will hear a beeping sound and the indicator light will flash continuously. The unit
will automatically pause evaporative cooling.
Refill the water tank to deactivate the alarm in cooling mode. First switch OFF the unit and unplug
from the power outlet. Fill the water tank with water above the minimum water level mark. Plug in and
switch ON again.
To deactivate the alarm and continue using the unit as a fan (without evaporative cooling), switch
the unit OFF and then ON again. The Low Water Alarm will not activate in Fan only mode. The Low
Water Alarm will sound again if the COOL function is activated while the water tank is still empty.
*Applicable for models with low water alarm feature only.
FILLING WITH WATER & ICE (CONTINUED)
LOW WATER ALARM*
WATER LEVEL INDICATOR LIGHT

7
USE & OPERATION (CONTINUED)
EN
CLEANING & DRAINING THE WATER TANK
If the cooler will not be used for a long period of time, please refer to the STORAGE & MAINTENANCE
GUIDELINES located in the separate Safety & Maintenance Guide.
WARNING:
Before cleaning the unit, switch the unit OFF and disconnect the power adapter from the unit and
electrical socket.
*Applicable for models with water filter feature only.
Slide out and empty the water tank.
Rinse the water tank with clean water.
Carefully remove the Water Tank Filter* (if your unit has this) from the tank. Remove dust and hair
from filter and then rinse with water until clean. Dry and replace the filter back into the water tank.
Use a damp cloth to remove dirt and dust from the surface of the unit. Never use corrosive
elements or chemicals to clean this product.
When the product is not in use, store the unit in a dry place out of direct sunlight.
•
•
•
•
•

8
USE & OPERATION (CONTINUED)
EN
WARNING:
Before cleaning the unit, switch the unit OFF and disconnect the power adapter from the unit and
electrical socket.
CLEANING THE CARBON DUST FILTER* AND HONEYCOMB COOLING MEDIA
The appliance is supplied with a Carbon Dust Filter* and Honeycomb Cooling Media.
The Carbon Dust Filter* and Honeycomb Cooling Media are located inside the Rear Grill. See
Figure 1 for instructions on how to remove them from the unit for cleaning and maintenance.
Do not run the unit in COOL mode with stale water in the tank. You must empty the water tank
and refill with fresh water, especially if the tank has not been cleaned in a long time.
The cleaning frequency for the Honeycomb media depends on local air and water conditions.
In areas where the mineral content of water is high, mineral deposits may build up on the
Honeycomb Cooling Media and restrict air flow. Draining the water tank and refilling with fresh
water at least once a week will help reduce mineral deposits. If mineral deposits remain on the
Honeycomb Cooling Media, the media should be removed and washed under fresh water. The
media should be cleaned every two months or sooner, depending on your needs.
For best results allow the Honeycomb Cooling Media to dry after each use by turning off the cool
function 15 minutes before turning the unit off.
•
•
•
•
•
Carefully remove the rear grill from the unit.
Remove the two band holders to release the
carbon dust filter*.
Rinse the filter with clean water and let it dry
before re-installing to the rear grill.
Pull out the Honeycomb Cooling Media. Slide
down and remove the Honeycomb Frame.
Replace or clean media with water and a damp
cloth as needed.
1.
2.
3.
4.
5.
Removing the Carbon Dust Filter*/ Honeycomb Cooling Media:
WARNING: DO NOT operate the Air Cooler when the
Rear Grill is removed from the Air Cooler, or if there
is a loose-fitting Rear Grill. Doing so can cause
serious injury or dangerous electrical shock.
*Applicable for models with Carbon Dust Filter only.
Figure 1:
Honeycomb
Frame
Honeycomb
Cooling Media Carbon Dust
Filter*
Band
Holder
Rear Grill

JMATEK Limited
Manulife Financial Centre,
Kwun Tong, Hong Kong
Phone: [phone]
Email: [email protected]
Web: www.jmatek.com
Made in China
© 2018 JMATEK Limited. All rights reserved.
The Honeywell Trademark is used under license
from Honeywell International Inc.
Honeywell International Inc. makes no
representations or warranties with respect to this product.
This product is manufactured by Airtek Int'l Corp. Ltd.
(subsidiary of JMATEK Ltd.).