Honeywell ChargeBase CT40-CB User manual

CT40 ChargeBase and NetBase
Model CT40-CB, CT40-NB
Quick Start Guide
CT40-CNB-EN-QS Rev A
08/18

1
Out of the Box
Make sure that your shipping box contains these items:
• CT40 ChargeBase (CT40-CB) or NetBase (CT40-NB)
• Power supply
• Power cord (if purchased)
• Regulatory Sheet
If any of these items are missing or appear damaged, contact
your Customer Account Representative. Keep the original pack-
aging in the event that you need to return the ChargeBase or
NetBase for service or if you want to store the charger while not
in use.
Caution: We recommend the use of Honeywell
accessories and power adapters. Use of any non-
Honeywell accessories or power adapters may cause
damage not covered by the warranty.
Mise en garde : Il est recommandé d'utiliser les
périphériques, les cordons d'alimentation et les
adaptateurs secteur conçus par Honeywell. L'utilisation
de tout périphérique, cordon d'alimentation ou
adaptateur secteur d'une autre marque est susceptible
de provoquer des dommages non couverts par la
garantie.

2
Connect Power
Use only a UL Listed power supply which has been qualified by
Honeywell with an output rated at 12V/7A. The power supply
input rating is 100-240 VAC, 50/60 Hz. The operating tempera-
ture is -10 °C to 50 °C (14 °F to 122 °F). The maximum output
for the base is 5VDC/2A.
1. Plug the power cord into the power supply.
2. Plug the power supply cable into the power connector on
the back of the charger.
3. Plug the power cord into a standard wall outlet.
Power Connector
Ethernet
(CT40-NB)

3
Charge the Battery Pack
Caution: Make sure that all components are dry prior to
using the computers and batteries with accessories. Using
wet components may cause damage not covered by the
warranty.
Mise en garde : Assurez-vous que tous les composants sont
secs avant de connecter les terminaux/batteries à des
périphériques. L'insertion de composants humides risque
de provoquer des dommages non couverts par la garantie.
• Insert one to four CT40s with battery pack inserted into the
ChargeBase or NetBase.

4
Mount the ChargeBase or NetBase
You can mount the charger on a flat, horizontal surface such as
a desktop or workbench with an optional DIN rail.
Mounting hardware required:
•DINrail
• 3/16-inch diameter x 5/8-inch long pan head screw
• 1/2-inch OD x 7/32-inch ID x 3/64-inch thick washer
• 3/16-inch diameter nut
1. Slide the DIN rail into the slot on the bottom of the Charge-
Base or NetBase.
2. Secure the DIN rail to the flat surface with the hardware.

5
Support
To search our knowledge base for a solution or log into the Tech-
nical Support portal and report a problem, go to
www.hsmcontactsupport.com.
User Documentation
For the user guide and other documentation, go to
www.honeywellaidc.com.
Limited Warranty
For warranty information, go to www.honeywellaidc.com and
click Resources > Warranty.
Patents
For patent information, see www.hsmpats.com.
Disclaimer
Honeywell International Inc. (“HII”) reserves the right to make
changes in specifications and other information contained in
this document without prior notice, and the reader should in all
cases consult HII to determine whether any such changes have
been made. The information in this publication does not repre-
sent a commitment on the part of HII.
HII shall not be liable for technical or editorial errors or omis-
sions contained herein; nor for incidental or consequential
damages resulting from the furnishing, performance, or use of
this material. HII disclaims all responsibility for the selection
and use of software and/or hardware to achieve intended
results.

6
This document contains proprietary information that is pro-
tected by copyright. All rights are reserved. No part of this docu-
ment may be photocopied, reproduced, or translated into
another language without the prior written consent of HII.
Copyright © 2018 Honeywell International Inc. All rights
reserved.