Honeywell RP2B User manual

RP2B/RP2D/RP4B/RP4D
Multi-Bay Battery Charger
Instructions
RP234MBC-EN-IN Rev C
5/18

Introduction
Honeywell’s Multi-Bay Battery Charger can fully charge up to
four lithium-ion batteries in less than eight hours. An RP2 bat-
tery typically takes 4 hours to fully charge, and an RP4 battery
takes 7 hours.
Multi-Bay Battery Charger Operation and Indicators
1. Connect the right angle power adapter to the Multi-Bay
Battery Charger. Then plug the power supply into an AC
power outlet. Make sure the AC power outlet voltage is the
same as the power supply.
Note: Use only a UL/cUL listed power supply with output rated
12Vdc. Contact your supplier for the appropriate power
supply for your location.

We recommend use of Honeywell approved power
adapters. Use of any non-Honeywell approved power
adapters may cause damage not covered by the warranty.

2. Place a battery into a cradle to charge with the battery
contacts facing the contacts on the charger.
3. When a battery is inserted, the solid red LED appears. If the
red LED does not appear or is flashing, check to make sure
the battery pack is seated completely in the charger with the
battery contacts facing the contacts on the charger.
4. When the battery is completely charged, the LED turns
green.
Operational temperature for charging the battery is 32° to
104°F (0° to 40°C). The storage temperature is -22° to 149°F (-
30° to 65°C).

About the Battery
Battery Recommendations
• Batteries are shipped approximately 30% charged or less and
should be fully charged for maximum charge capacity.
• The battery is a lithium ion cell and can be used without a full
charge, and can also be charged without fully discharging
without impacting the battery life. There is no need to perform
any charge/discharge conditioning on this type of battery.
• Do not disassemble the battery. There are no user-serviceable
parts in the battery.
• Do not allow metallic conductive objects to contact battery
terminals. Do not short-circuit a battery or throw it into a fire;
it can explode and cause severe personal injury.
• Improper battery use may result in a fire, explosion, or other
hazard.
• Although your battery can be recharged many times, it will
eventually be depleted. Replace it after the battery is unable to
hold an adequate charge.
• If you are not sure if the battery or charger is working properly,
send it to Honeywell International Inc. or an authorized service
center for inspection. Refer to Technical Assistance for
additional information.
Use only Honeywell Li-ion battery packs 50133975-
001 or 550053-000 in this device. Use of any non-
Honeywell battery may result in damage not covered
by the warranty.

Proper Disposal of the Battery
When the battery has reached the end of its useful life,
the battery should be disposed of by a qualified recy-
cler or hazardous materials handler. Do not incinerate
the battery or dispose of the battery with general waste
materials. You may send the scanner’s battery to us.
(postage paid). The shipper is responsible for complying with all
federal, state, and local laws and regulations related to the
packing, labeling, manifesting, and shipping of spent batteries.
Contact Product Service and Repair for recycling or disposal
information. Since you may find that your cost of returning the
batteries significant, it may be more cost effective to locate a
local recycle/disposal company.
Cleaning the Multi-Bay Battery Charger
Unplug the Multi-Bay Battery Charger from the power supply
before cleaning.
Clean the housing of the Multi-Bay Battery Charger with a soft
cloth or tissue dampened with water (or a mild detergent- water
solution). If a detergent solution is used, rinse with a clean tis-
sue dampened with water only.
Never use solvents (e.g., alcohol or acetone) on the
housing. Solvents may damage the finish.

Disclaimer
Honeywell International Inc. (“HII”) reserves the right to make
changes in specifications and other information contained in
this document without prior notice, and the reader should in all
cases consult HII to determine whether any such changes have
been made. The information in this publication does not repre-
sent a commitment on the part of HII.
HII shall not be liable for technical or editorial errors or omis-
sions contained herein; nor for incidental or consequential
damages resulting from the furnishing, performance, or use of
this material. HII disclaims all responsibility for the selection
and use of software and/or hardware to achieve intended
results.
This document contains proprietary information that is pro-
tected by copyright. All rights are reserved. No part of this docu-
ment may be photocopied, reproduced, or translated into
another language without the prior written consent of HII.
2017 Honeywell International Inc. All rights reserved.
Web Address: www.honeywellaidc.com
Customer Support
Technical Assistance
To search our knowledge base for a solution or to log in to the
Technical Support portal and report a problem, go to
www.hsmcontactsupport.com.
Product Service and Repair
Honeywell International Inc. provides service for all of its prod-
ucts through service centers throughout the world. To obtain
warranty or non-warranty service, you must first obtain a Return
Material Authorization number (RMA #) and then return your
product to Honeywell (postage paid) with a copy of the dated

purchase record.
To learn more, go to www.honeywellaidc.com and select Service
& Repair at the bottom of the page.
Limited Warranty
For warranty information, go to www.honeywellaidc.com and
click Get Resources > Product Warranty.