Honeywell NOTIFIER INSPIRE E10 User manual

Notifier INSPIRE E10/E15
Fire Alarm Control Panels
Installation Instructions

2
CONTENTS
Introduction 4
System Equipment 5
Personnel 5
How to use this guide 6
Pre-installation Check List 7
Installation Overview 9
Cables 10
Panel Technical Data 15
Notes to Installer 22
Panel Parts 24
Parts of Notifier INSPIRE Panels 26
Unpacking a Notifier INSPIRE E10 Panel 27
Unpacking a Notifier INSPIRE E15 Panel 28
Extension and Options 30
Panel Installation 31
Mounting height 31
Backbox spacers 31
Surface mount 32
Side Covers 33
Wall Recess for Semi Flush Fixing a Panel 34
Front Door 36
Module Carriers and Slots 37
Location of modules in Carrier slots 38
To Fit terminal Blocks 39
To Remove terminal Blocks 39
To Fit Protection Cover Over Backbox 40
To Fit a Module 41
To Remove a Module 41
Cable Screen to Earth 42
Cable Routing 42
Cable length and label 43
Terminal number Label 43
MODULE and Terminal blocks IDENTIFICATION 44
RESET Hole 44
Loop (OPAL x 2) Module 45
How loop circuits get numbered 46
OPAL Devices 48
Fire Protection Equipment (FPE) 52
CPU Module Notifier 53
Charger Module 55
ID²Net Network Module 56
Serial Communication Interface Module 59
4 Channel I/O Module 61
FARE / FRE Module 63
Communication Dual (FAT/FBF) Module 66
Mains Supply 69
Battery installation 70
Fitting a language film insert 73
Fitting the HMI cable 74
Commissioning 75
Configuration and System Test 76
Maintenance 77
General 77
Routine Testing 77
Batteries 77
Fault monitoring and rectification 77
Standards 78
Option with requirements EN542 79
Appendix A 81
Ecodesign requirements for Electronic Displays 81

3
Notifier INSPIRE E10/E15 Control Panels - Installation instructions
RELATED DOCUMENTS
In addition to this guide refer to:
Operating Manual INSPIRE E10/E15 Control Panel (Part
number HOP3389EN)
Commissioning Manual INSPIRE E10/E15 Control Panel
(Part number HOP1388EN)
Notifier Cybersecurity Manual (EMEA) (Part number
41881122)
Safety Information (Part number 41881123)
CONVENTIONS
Where appropriate, in this manual there are advisory
warnings and cautions to remind you to consider safety at all
times, especially when following the procedures described.
This symbol precedes a note that highlight
important information that is normally
hidden in the main text.
This symbol precedes information that
warns of danger that may result in serious
injury or death, also used in a caution to
prevent damage to the equipment.
This symbol precedes information about
compliance with standard(s).
ABBREVIATIONS
CIE Control and Indicating Equipment
CPU Central Processing Unit
E10 10U size Panel enclosure
E15 15U size Panel enclosure
EMC Electromagnetic compatibility
FARE Fire Alarm Routing Equipment
FE Functional Earth
FRE Fault Routing Equipment
FPE Fire Protection Equipment
HMI HumanMachine Interface
IO or I/O Input or Output
LED Light emitting diode (light)
MCP Manual call point
OC or O/C Open circuit
RAL European colour matching
system
SC or S/C Short circuit
SELV Separated Extra Low Voltage
PE Protective Earth
PELV Protected ExtraLow voltage
PSE Power Supply Equipment

4
Introduction
Introduction
The purpose of this manual is to provide the user with all recommended procedure descriptions and full technical
details for the successful installation and basic commissioning of INSPIRE Fire Alarm Control Panel based Fire
Control System.
EQUIPMENT DESIGN
An INSPIRE E10/E15 panel, the Control and Indicating Equipment (CIE) including its integral Power Supply
Equipment (PSE) design has been carried out in accordance with a quality management system, which
incorporates a set of rules for the design of all elements of the CIE and PSE. The components of the CIE and PSE
have been selected for the intended purpose, and are expected to operate within their specification when the
environmental conditions outside the cabinet of the CIE comply with class 3k5 of EN 6072133.
SYSTEM DESIGN AND PLANNING
It is assumed that the system, of which the Notifier INSPIRE E10/E15 equipment (Control and Indicating
Equipment CIE) is a part, has been designed by a competent fire alarm system designer in accordance with the
requirements of local codes of practice that are applicable.
The design drawings (also referred to As Fitted Drawings) should clearly show the positions of all the Notifier
INSPIRE system equipment installation on site, these include panel, loop devices and external equipment that is
part of the system.

5
Notifier INSPIRE E10/E15 Control Panels - Installation instructions
SYSTEM EQUIPMENT
The INSPIRE E10/E15 Control panel is designed for use with Notifier by Honeywell range of addressable detector,
control and monitoring modules and addressable call points. It supports both OPAL and CLIP loop polling
protocols.
The design of each INSPIRE E10/E15 Control panel is based on a modular build concept which offers the
user completely flexible system solutions. Each Control panel comprises separate build assemblies to simplify
the installation process. The electronic components are contained within purpose built module enclosure
specifically designed to simplify panel installation; various module options are available to meet different market
requirements. There is space provision for two sealed lead-acid batteries in the respective Control panel builds.
There is room inside the enclosure to accommodate additional module carrier(s) and modules to build a system
and for future system expansion. Additional modules are easy to install providing the recommended procedures
described in this manual are followed.
To avoid inadvertent contamination of the panel’s electronics, the manufacturer recommends that installation of
the enclosure containing the electronics, the modules, only takes place after all other trades have completed their
tasks.
PERSONNEL
Installation and maintenance of this product must be carried out only by suitably-qualified, trained and skilled
electrical engineer.

6
Introduction
HOW TO USE THIS GUIDE
This Installation Guide is intended to provide you with simple guidelines on how to install the INSPIRE E10/E15
Control panel quickly and safely.
The modular design of the INSPIRE E10/E15 Control panel offers configurations to meet the requirements of
different markets. Thus, the installation procedures differ regarding the wall mounting of the enclosure and
installation of optional modules where these markets demand operational compliance.
Where further explanation is needed regarding these issues refer to the various appendices.
For each stage in the INSPIRE E10/E15 Control panel installation and initial commissioning power up procedures
a brief description is given of its purpose with graphics to make the instructions easy to follow.
WARNINGS AND CAUTIONS
Procedures described in this manual include appropriate warnings and cautions to guide the user towards
adopting safe and methodical work practices during the installation and commissioning phases.
You are alerted to any areas where high voltage is present, or where there may be a risk of damage to Control and
Indicating Equipment (CIE) if the recommended procedures described in this manual are not followed.

7
Notifier INSPIRE E10/E15 Control Panels - Installation instructions
Pre-installation Check List
Before installing a INSPIRE E10/E15 Fire alarm equipment you must first ensure that the following criteria have
been met. Failure to do this may not only result in damage to the equipment, but may also cause problems when
commissioning the equipment or adversely affect its performance.
DO’S AND DON’TS
DO Ensure the operating ambient temperature where the panel is installed is in the range: 5°C to +40°C
DO Ensure the panel is installed where the relative humidity is between: 5% and 95% non-condensing
DO Ensure the panel is installed in an area where ingress of solids and liquid is not beyond IP30 rating
DO NOT site the panel where there would be restricted access to the inside of the equipment and to the
internal cabling and wiring connections points.
DO NOT locate the panel where there are high levels of vibration or shock
TRANSIENT PROTECTION
This equipment contains transient-protection devices. Although no system is completely immune from lightning
transients and interference and for a system to function correctly and to reduce susceptibility, this equipment
must be earthed correctly.
As with all static sensitive electronic components this system may operate erratically or can be damaged if
subjected to lightning-induced transients.
The use of overhead or outside aerial wiring is not recommended due to the increased susceptibility to nearby
lightning strikes.

8
Pre-installation Check List
CHECKING YOUR PANEL FOR DAMAGE
It is important to check all supplied equipment for damage before proceeding with the installation!
Before attempting to install the INSPIRE E10/E15 Control panel, or other equipment, you must do the following:
01 After removing the INSPIRE E10/E15 Control panel, modules and other related equipment from its packaging,
and before you proceed with installing it in its chosen location, check for any damage that may have occurred
while in transit.
Note: In the unlikely event that any of the supplied INSPIRE E10/E15 Control panel items has been damaged,
you MUST NOT install it but return it to your supplier, see the following section.
02 If you are satisfied that none of the supplied items has been damaged, you can now proceed with installation.
Refer to the relevant sections that apply to your installation/configuration requirements.
WHAT TO DO IF EQUIPMENT IS RECEIVED DAMAGED
If you have problems regarding the quality of any supplied order items including the INSPIRE E10/E15 Control
panel, its ancillaries or items are missing, follow the procedure below.
01 DO NOT continue with the installation but contact your supplier for advice on what to do next. Similarly, if the
product is found to be faulty during installation contact your supplier immediately.
02 To aid your supplier and the manufacturer, you are requested to quote the manufacturer’s unique batch
reference number which can be found on the packaging or inside the back box
03 Note all the details relevant to your complaint, date of receipt, packaging condition and forward it your
supplier.
04 Where the product needs to be returned to your supplier, you are requested to use the original packaging, or
suitable anti-static equivalent, wherever possible.

9
Notifier INSPIRE E10/E15 Control Panels - Installation instructions
Installation Overview
The panel range is designed for mounting onto an internal wall of a protected building and is not suitable for
mounting on to external wall.
01 Install the panel enclosure in accordance with the instructions to be found in this guide.
02 Bring the field wiring/cables through the recommended entry points on the backbox. Prepare all cable/wiring
entry with appropriate fire industry-approved cable glands and label all field wiring correctly to aid termination.
03 Install a fire industry-approved, AC mains power supply isolator ‘fused spur unit’ close to the INSPIRE E10/
E15 Panel. The mains supply cable must be brought into the enclosure, using a recommended cable entry
point.
04 Use this guide for recommendations on how to install batteries inside the enclosure.
05 Once individual cables are checked make the wiring of each circuit. The battery link is fitted during the
commissioning power up stage.

10
Cables
Cables
All wiring must comply with local wiring regulations. Note also the requirements for cabling and interconnection
of a fire detection and alarm system. For information on wiring inputs and outputs refer to the appropriate module
and wiring to their terminals.
CABLING INSTRUCTIONS
01 Cables must be brought into the enclosure using the 20 mm cable entry points provided on the top and rear of
the panel enclosure. Ensure that all openings in the enclosure are closed before connecting power to the panel
to prevent inadvertent access to hazardous voltages.
02 Tails must be of sufficient length to connect to the respective terminal at the commissioning stage.
03 Cables that are screened must be terminated at the panel enclosure and earthed at points provided on the top
side.
04 The mains supply must be suitably fused and rated as per specifications, mains supply must have a dedicated
spur from the site distribution board with an over-current protection device rated at a maximum of 16 A.
05 The cable entry points on the extreme right-hand side must be used for mains cable entry. DO NOT route
mains cable using any other cable entry points and ensure that the mains wiring is always separated from the
low voltage wiring. It is good practice to always isolate the mains power at the external isolator equipment to
make the panel safe when performing maintenance tasks involving the panel’s electronic equipment.
06 All low voltage cables must have a minimum 300 V AC rating.
CABLE GLANDS
Fire-industry-approved, M20 cable glands must be used, that are made out of metal or having flammability class
V1 rating or better.