Honeywell Notifier LCD6000N User manual

LCD6000N
LCD Remote panel
Installation
manual

LCD6000N Installation Manual INDICE
LCD6000N_manu-inst Doc. M-183.1- LCD6000N-ENG Rev A.2 NOTIFIER ITALIA
INDEX
Detectionsystemlimits 1
Generaldescription 2
Installation 3
Front panel controls 4
User interface description 5
Normalcondition 5
Events from zone in alarm condition 6
Events from zone in fault condition 7
PROGRAMMINGMENU’ 8
Address 8
Password 9
Buzzervolume 9
LEDTest 9
LCDTest 9
RS485Serialconnection 10
Shield cable and earth connection 11
Topographic LCD6000N board 12
CN1Terminalblock 13
Environmentalfeatures 13
Powersupply 13

LCD6000N Installation Manual PAGE - 1
LCD6000N_manu-inst Doc. M-183.1-LCD6000N-ENG Rev A.2 NOTIFIER ITALIA
NOTE: Do not try to install the LCD6000N without having read this manual.
WARNING: This manual refers to all the features available in software revision
indicated on manual’s cover.
DETECTION SYSTEM LIMITS
A security or fire detection system is useful for timely advice of each dangerous event, like fire, theft,
intrusion and in some cases can provide automatic event management (evacuation messages diffusion,
automatic extinguishing systems, CCTV plants interfacing, door and accesses lock, automatic warning of
authorities etc.) but in any case, does not assure protection against property damage or resulting from fire or
theft in general. Each system also can not function properly if not installed and maintained according to
manufacturer's instructions.
PRECAUTIONS
These instructions contain procedures to follow to avoid devices damages. We assume that the
user of this manual has previously attended a course and knows applicable laws and
regulations.
The system and devices must be installed in an environment with the following characteristics:
Temperature: -5°C to +40°C
Humidity: 10 % - 93 % (without condensate).
Devices (sensors etc.), not perfectly complying with the control panel can cause damages to the
control panel or system malfunctioning, and this could even happen at the worst time. That’s
why it’s essential to use only material that is indicated by NOTIFIER as compatible with its
control panels. In case of doubt check with NOTIFIER technical assistance.
This system and all its solid state components, can be damaged by induced electrostatic
discharges: handle the boards picking them on borders and avoid to touch electronic
components.
A good grounding connection ensures noise sensitivity reduction
Consult Technical Service NOTIFIER if you are unable to solve installation problems
Any electrical system requires proper power supply. Whether mains is missing, the system can
work with backup batteries, but only for a limited time.
During plant’s programming, consider required autonomy in order to choose the correct power
supply and battery
Periodically check batteries’ level by qualified personnel
Disconnect mains and batteries BEFORE removing or adding any board
Disconnect all power sources, BEFORE performing any service operation
Control panel and connected devices (sensors, modules, annunciators etc.) can be damaged if
a board is inserted or removed, or if cables under voltage are connected.
The most common cause of malfunctioning is bad maintenance
Take care of these issues particularly from the stage of system design, to facilitate and thereby
reduce the future cost of interventions
This device is marked CE, to certify its quality and compliance with European community’s regulations
Electromagnetic Compatibility Directive 89/336/EEC (and 92/23/EEC directive)
Low Voltage Directive 73/23/EEC

PAGE - 2 Installation Manual LCD6000N
NOTIFIER ITALIA Doc. M-183.1-LCD6000N-ENG Rev A.2 LCD6000N_manu
National regulations
This device must be installed and operate in compliance with these instructions and
installing place local regulations.
GENERAL DESCRIPTION
DESCRIPTION
LCD6000N is a LCD remote panel for the new series of AM-2000, AM-4000, AM-6000 control panels.
A control panel can connect up to 12 or 16 LCD6000N as remote repeater panel according to the type of
control panel.
The remote repeater LCD6000N display all reports of control panel and allow to performs the following
functions:
ALARM ACKNOWLEDGMENT;
OUTPUT TACITATION;
RESET ALARMS.
FUNCTIONING
The repeater needs of local configuration for the assignment of peripheral address.
LCD6000N displays time, date and personalized messages from the AM Series control panel.
Using the function keys of the LCD6000N repeater can be successfully performed the following functions:
- Buzzer tacitation, Output tacitation, Reset alarm and Lamp Test.
- It also allows viewing of the events list on the control panel divided by: Alarms, Fault, System fault.
Technical features:
Microprocessor based system
LCD graphic 320 x 240 pixel display
Keyboard with dedicated keys for special functions: Buzzer tacitation, Sounder tacitation, Reset,
LampTest.
Serial lines:
- 1 RS 485 interface
Voltage range:
10÷30Vdc
Connection
-2 wire (power)
- 2/3 wire for serial wiring (2 with common power, 3 with separate power)
Mechanical:
LCD6000N is suitable for wall mounting installations.
Dimensions 180mm (W) x 168mm (H) x 55mm (D)
IP rating: IP 20
Temperature range: -5°C ÷ +40°C
CONTROL PANEL LCD6000N
LCD6000T LCD6000A TOTAL INSTALLABLE LCD
AM2000 max 12 max 10 16
AM4000 max 16 max 14 22
AM6000 max 16 max 16 24
TAB.1

LCD6000N Installation Manual PAGE - 3
LCD6000N_manu-inst Doc. M-183.1-LCD6000N-ENG Rev A.2 NOTIFIER ITALIA
INSTALLATION
Dimensions for wall-mount
It is recommended to not install the LCD6000N control panel close to heat sources (radiators, heaters, etc..).
The panel is designed to be wall-
mounted through 4 self-blocking nogs
(stone walls) or self-tapping screws (pre-
built panels etc.)
Screws diameter must be 5mm max. We
advice not to install the panel near
heating sources (radiators etc.)
Fixing screws 5mm max.
Fix the incoming cable
with a tie.
Plug-in the cable into CN1
Front panel fixing screws

PAGE - 4 Installation Manual LCD6000N
NOTIFIER ITALIA Doc. M-183.1-LCD6000N-ENG Rev A.2 LCD6000N_manu
FRONT PANEL CONTROLS
FRONT PANEL SIGNALLING
ALARM (Red):
Flashes if there is at least one device in alarm condition that has not yet been recognized.
On Fixed if all alarm events have been recognized.
FAULT (Yellow):
Flashes if there is at least one fault that has not yet been recognized.
On Fixed if all fault events have been recognized.
TACITATION (Yellow):
On if acknowledgment key have been previously pressed.
SOUNDER ACKNOWLEDGMENT
In alarm condition the following devices are active:
- Control panel sounder output
- Control module Type-ID HORN programmed
- All control module activated by CBE association
This button disable the following devices:
- Control panel sounder output
- Control module Type-ID HORN programmed enabled for tacitation.
- All control module activated by CBE association enabled for tacitation.
This requires the level 2 password.
To access the level 2 password, press key, the entry window will be shown. With arrow keys
select first number, than press to confirm. Repeat this step to enter the entire password.
BUZZER TACITATION: this key silence LCD6000N
and control panel buzzer and enable the operator to RESET.
RESET: by pressing this key, you can cancel
the memory of current alarms or fault points. It
deactivates sirens and switches off all light
signallings of the alarm sensors.
This operation require level 2 password.
To enter the level 2password press the button
, a window will open for entering the
password.
Use the arrow keys to select numers
and press to confirm and move to the
next. Repeat this step to enter the entire
password.
ARROWS: selection keys. LISTE : this button in case of alarm or
fault from area, allows to view the list of
individual points in alarm or fault.
LAMP-TEST: this key executes the
lamp-test (LEDs blink for few seconds
and then the test is performed on
screen).
Holding down this button for a few
seconds, the user can access to the
configuration menu of the LDC6000N.

LCD6000N Installation Manual PAGE - 5
LCD6000N_manu-inst Doc. M-183.1-LCD6000N-ENG Rev A.2 NOTIFIER ITALIA
USER INTERFACE DESCRIPTION
NORMAL CONDITION
The following screen is displayed when the panel LCD6000 there are no fault conditions (alarm or fault):
Counter areas in fault
Panel icon status.
In normal condition, without alarm and fault, the NOTIFIER trademark symbol is present.
In the presence of points or zone not included an exclamation is displayed (!).
In alarm condition the symbol Flame is displayed.
In fault condition the symbol Triangle is displayed.
Note: The alarm state prevails in the event that the panel is alarm and fault condition simultaneously.
Date - Time
Counter areas
in alarm
Counter system fault
Counter zone
excluded
Serial connection RS485 status
In case of failure on the serial connection
"OFF LINE" will displayed.
Serial connection icon status.
In case of failure on the serial
connection the icon will
displayed as follow:

PAGE - 6 Installation Manual LCD6000N
NOTIFIER ITALIA Doc. M-183.1-LCD6000N-ENG Rev A.2 LCD6000N_manu
E
Ev ve en nt ts s f fr ro om m z zo on ne e i in n a al la ar rm m c co on nd di it ti io on n
The following screen is displayed when the control panel has a zone in alarm.
With arrow keys  it is possible to scroll through the list of zones in alarm.
If there are several zone alarm, to display the devices in a given area; scroll through the list of zones until the
selected zone is in the viewing area.
Use key to access the list of points in alarm of the selected zone.
With arrow keys it is possible to scroll the list of the devices in alarm.
Counter zone in alarm
Date and time of
the first event zone
alarm
First zone alarm
Programmed text
for the zone
Last alarm zone
Programmed text
for the zone
Date and time of
the last event zone
alarm
Devices in alarm
S = detector
M = module
Text programmed
for the device
TYPE-ID
Display area of
the first event
Display area of the
last event

LCD6000N Installation Manual PAGE - 7
LCD6000N_manu-inst Doc. M-183.1-LCD6000N-ENG Rev A.2 NOTIFIER ITALIA
E
Ev ve en nt ts s f fr ro om m z zo on ne e i in n f fa au ul lt t c co on nd di it ti io on n
The following screen is displayed when the control is in zone fault condition.
Even the events of fault are initially displayed by zone.
With arrow keys it’s possible to scroll the list fault zone.
If there are several fault zone, to display the faulty devices in a given area; scroll through the list of zones until
the selected zone is in the viewing area.
Use key to access the list of fault points of the selected zone.
With arrow keys it is possible to scroll the list of the devices in fault.
Fault zone
Programmed
text zone
Faulty device
D = detector
M = module
Programmed
device text
TYPE-ID
Counter fault zone
Date and time
of the first
event of zone
fault
Date and time of the
last event zone fault
Display area of
the first event

PAGE - 8 Installation Manual LCD6000N
NOTIFIER ITALIA Doc. M-183.1-LCD6000N-ENG Rev A.2 LCD6000N_manu
PROGRAMMING MENU’
To enter in the initial configuration programming menu of the LCD6000N, hold the key for a wile.
To change the panel configuration the 3A password level is required. To access the password level 3A
press for a wile then the entering windows will displayed. With arrow keys select first number,
than press to confirm. Repeat this step to enter the entire password.
The following menu will displayed:
Where:
Address
Select “Address” voice to assign peripheral number to LCD6000N.
Use arrow key to select device number and press list key to confirm. 16 available device address for
LCD6000N.
Use arrow keys 
To select the function
to change and press list key
to confirm and access to
the function.

LCD6000N Installation Manual PAGE - 9
LCD6000N_manu-inst Doc. M-183.1-LCD6000N-ENG Rev A.2 NOTIFIER ITALIA
Password
PASSWORD LEVEL 2 – For acknowledgement or reset LEVEL 2 password is required. After pressing the
corresponding key the entering window for the password entry will displayed. With arrow keys select
first number, than press to confirm. Repeat this step to enter the entire password. Default password is
22222.
3A LEVEL PASSWORD – Press key for a wile to get 3A LEVEL password, than entering window for the
password entry will displayed. With arrow keys select first number, than press to confirm. Repeat
this step to enter the entire password. Default password is 44444.
Buzzer volume
Selecting “Buzzer volume” with the arrow keys to scroll the list, than list key to confirm it is possible to set
buzzer volume for alarm and fault.
LED Test
Selecting “Test Led” with the arrow keys, than list key to confirm. The LCD6000N perform the lamp-test
LCD Test
with the arrow keys, than list key to confirm. The LCD6000N perform the display test.

PAGE - 10 Installation Manual LCD6000N
NOTIFIER ITALIA Doc. M-183.1-LCD6000N-ENG Rev A.2 LCD6000N_manu
RS485 Serial connection
The connection of LDC6000N with the control panel use serial line RS485.
RS-485 line must be installed in “MULTI-POINT” configuration (daisy chain).
Each peripheral must be programmed with an address between 1 16. (refer to TAB.1).
“Multi-Point” configuration (Daisy Chain)
Connect two wires to the RS485
control panel terminal block
(LIN+ and LIN- ) to the
corresponding terminals of the
first device on the line.
Continue wiring from the first
device to the next, and so on.
Install EOL (120-150,0.5W) on
the terminal block on both
control panel and last device of
the line.
Maximum length between control
panel and last device 1,5 km.
Use shielded cable with
appropriate section type
Belden 9574 or 9575
AM-2000
13
EOL= 120 
12
7
EOL= 120 
2322
LCD-6000N
1 2 3 4 5
GND+24
V
LCD-6000N
1 2 3 4 5
AM-4000
17
EOL= 120

16
11
EOL= 120 
3130
LCD-6000N
1
2
3 4 5
GND+24
V
LCD-6000N
1 2 3 4 5
AM-6000
09
EOL= 120 
087
EOL= 120 
21
LCD-6000N
1 2 3 4
5
GND+24
V
CN
C
N
LCD-6000N
1 2 3 4 5
Typical wiring RS485 with 24Vdc power supply in common
(Control panel user output voltage 24Vdc)

LCD6000N Installation Manual PAGE - 11
LCD6000N_manu-inst Doc. M-183.1-LCD6000N-ENG Rev A.2 NOTIFIER ITALIA
Installation with separate power supply
Shielded cable and Earth connection
During installation, you need to consider
the consequences of remote ground
connections.
Connecting RS485 circuits, if there is a
ground wire (drain), this MUST NOT
be connected at chassis of the
equipment.
The shield must be connected only at the
control panel. Leave the other tail
disconnected and isolated
A B
Shield:
linking together the
two cable socks
Typical control
panel wiring
A B
Shield:
Connect to the
frame with a M5
lug
Use the location
closest to the
connector on the
chassis
Typical wiring of
the lastdevice
RS485 shield and earth wiring
Connect two wires to the RS485
control panel terminal block (LIN+
and LIN- ) to the corresponding
terminals of the first device on the
line.
Continue wiring from the first device
to the next, and so on.
Install EOL (120-150,0.5W) on the
terminal block on both control
panel and last device of the line.
Maximum length between control
panel and last device 1,5 km.
Use shielded cable with appropriate
section type Belden 9574 or 9575
AM-2000
13
+24V GND
EOL= 120 
127
+24V GND EOL= 120 
LCD-6000N
1 2 3 4 5
LCD-6000N
1 2 3 4 5
AM-4000
17
+24V GND
EOL= 120 
16
11
+24V GND EOL= 120 
LCD-6000N
1 2 34 5 LCD-6000N
1 2 3 4 5
A
M-6000
09
+24V GND
EOL= 120 
087
+24V GND EOL= 120

LCD-6000N
1 2 3 4 5
CN0
LCD-6000N
1 2 3 4
5
Typical wiring RS485 with 24Vdc
separate power supply
( LCDs are powered by auxiliary
remote power supply).

PAGE - 12 Installation Manual LCD6000N
NOTIFIER ITALIA Doc. M-183.1-LCD6000N-ENG Rev A.2 LCD6000N_manu
Topographic LDC6000N board
Cables specifications
Up to 1.200 mt. 18 AWG Belden 9574 type
Up to 1.500 mt. 16 AWG Belden 9575 type
1
2
34
5
CN1 Terminal block
CNT terminal
block for front
keypad
Buzzer

LCD6000N Installation Manual PAGE - 13
LCD6000N_manu-inst Doc. M-183.1-LCD6000N-ENG Rev A.2 NOTIFIER ITALIA
CN1 Terminal block
N° Terminal
block Description Note
5
LIN –
RS 485 Serial line
4 GND
Negative reference for serial line RS 485*
3 LIN +
RS 485 Serial line
2 GND
Power input
1 + 24Vdc
* TO BE USED IN CASE OF POWER NOT COMMON WITH THE CONTROL PANEL.
ENVIRONMENTAL FEATURES
Operative temperature: - 5°C ÷ + 40°C.
Humidity: 10% ÷ 93% (without condensate).
Stock temperature: -10°C - + 50° C.
Weight: 0,54Kg
Power supply
Voltage range: 10÷30Vdc.
Current in normal condition (without fault or alarms) with display off: 30mA
Current in alarm condition (with fault or alarms) with display on and buzzer active: 81mA

NOTIFIER ITALIA S.r.l.
A socio unico - 20097 San Donato Milanese (Ml) - Via Grandi, 22 - Tel.: [phone] - Fax: [phone] - Capitale Sociale €
2.700.000,00 i.v. - C.C.A.A. 1456164 - Trib. Milano Reg. Soc. 348608 - Vol. 8549 Fasc. 8 - Partita IVA IT 11319700156
(informativa privacy art. 3 Digs 196/03).
UFFICI REGIONALI:
10143 Torino – Corso Potenza, 6 - Tel.: [phone] - Fax: [phone] - E-mail: notifier.t[email protected] - 35010 Limena (PD) Via
IV Novembre, 6/c Int. 9 - Tel.: [phone] - Fax: [phone] - E-mail: [e-mail] - 40050 Funo di Argelato (BO) -
Asta Servizi, Bl. 3B, Gall. B n. 85, Centergross - Tel.: [phone] - Fax: [phone] - E-mail: [email protected] - 50136
Firenze –Via Aretina, 167/M Tel/Fax: [phone] - 00118 Roma - Via Del Casale Santarelli, 51 - Tel.: [phone] - Fax: [phone]
- E-mail: [e-mail] - 80143 Napoli - Palazzo Prof. Studi - Centro Direzionale, Isola E2, Scala B, Piano 5° - Tel.:
081/19493111 - Fax: [phone]- E-mail: [email protected]t - 70125 Bari - Via Delia Costituente, 29 - Tel.: [phone] -
Fax: [phone] - E-mail: [email protected] - 95128 Catania - Viale Alcide De Gasperi, 187 - Tel.: [phone] - Fax:
095/7120753 - E-mail: [e-mail]
20097 Tel: [phone]
San Donato Milanese Fax: [phone]
(MILANO) www.notifier.it
Via Grandi, 22 E-mail: [email protected]
A Honeywell company
Every care has been taken in the preparation of this data sheet but no liability can be accepted for the use of the information therein. Design features may be changed or amended without prior notice.
M-183.1-LCD6000N-ENG Rev A.2 11/2017