Honeywell XLS80e User manual

XLS80e
Panel Configuration
Manual
March 2007, Issue 9

i
XLS80e Fire Alarm Control Panels
Honeywell, Issue 9
March 2007
Quick Contents Reference by
Section
XLS80e
0 1 2 3
4 5 6 7
8 9
User Menu:
3:Log/display/print menu
4:Set Clock
5:View larm Count
6:
Service Mon 01-May-2000 11:20:07
Configuration
User Menu:
1:
2:Disable/enable
3:Log/display/print menu
4:Set Clock
Service Mon 01-May-2000 11:20:07
Test
DISPLAY:
SUMMARY - SEE SECTION
DETAILED DESCRIPTION OF MENUS, SEE SECTION:
4
CONFIGURATION MENU:
OVERVIEW - SEE SECTION
DETAILED DESCRIPTIONS, SEE SECTION:
3
12
12
10
ALSO:
TIME-OF-DAY - SEE SECTION
SENSITIVITY & DELAYS RECOMMENDATIONS - SEE SECTION
UPGRADING THE SOFTWARE - SEE APPENDIX
AVAILABLE LOOP DEVICES - SEE APPENDIX
XLSNET - SEE APPENDIX
9
13
1
2
3
POWER ON -
SEE SECTION 2
CONFIGUR TION:
1:
2:Zone Text Editor
3:Panel Text Editor
4:Control Matrix Configuration
Service Mon 01-May-2000 11:20:07
Loop Device Configuration
5
6
7
CONFIGUR TION:
4:Control Matrix Configuration
5:Network Configuration
6:Panel Settings
7:
Service Mon 05-DEC-2005 11:20:07
Virtual Point Configuration
14
8, 11
15

ii
XLS80e Fire Alarm Control Panels
Honeywell, Issue 9
March 2007
Contents
1 Introduction 1
1.1 Associated Documents 1
1.2 System Design and Planning 1
1.3 Glossary of Icons 2
1.4 Software Version Number 4
1.5 EN54 Functions 4
1.6 Ancillary Functions 5
2 Power On/Start Up 7
3 Panel Configuration Overview 9
3.1 Where to Access the Configuration Actions 9
3.2 Configuration Actions 10
3.3 Using the Panel Controls and Indicators 11
3.3.1 Pushbuttons 11
3.3.2 Liquid Crystal Display 12
3.4 Using the Off-line Support Tool 13
3.5 Passcodes 13
3.6 Learn Devices on Loops 14
3.7 Configure Group of Devices 15
3.8 Configure Individual Device 15
3.9 Text Editing 16
3.10 Control Matrix 16
3.11 Time-of-Day 17
3.12 Setting the Clock 17
3.13 Panel Settings 17
3.14 System Networking 18
3.15 Delays 19
3.16 Virtual Point Configuration 19
4 The Display - Tabs, Events and
Menus 20
4.1 Introduction 20
4.1.1 Status: NORMAL 20
4.1.2 Tabs 20
4.1.3 Events 20
4.1.4 Menus 20
4.2 Tabs 21
4.3 Event Displays 22

iii
XLS80e Fire Alarm Control Panels
Honeywell, Issue 9
March 2007
4.4 Menu Displays 25
4.4.1 To Display the User Menu 25
4.4.2 To Navigate Through the Menus 26
4.4.3 Menu Structure 27
5 Loop Device Configuration 29
5.1 Configure Individual Device 29
5.1.1 Select a Device 29
5.1.2 Change Device Configuration
- Sensors 31
5.1.3 MULTI, MCS & GAS Sensitivities 37
5.1.4 Change Device Configuration
- Modules 39
5.2 Configure Group of Devices 43
5.3 Learn Devices on Loops 45
5.3.1 Starting the Procedure 45
5.3.2 Run in Auto-Learn Mode 47
5.3.3 Run in Manual Learn Mode 49
5.3.4 Error Messages 49
5.3.5 End of Learn Process 50
5.4 Change Zone Number 50
6 Text Editing 51
6.1 Text Editing Pushbuttons 51
6.2 The Character Set 52
6.3 Zone Text Editing 52
6.4 Panel Text Editing 53
7 Control Matrix 54
7.1 Introduction 54
7.1.1 EN54 Requirements 55
7.2 Input Categories 56
7.3 Output Categories 58
7.4 Output Modes 59
7.5 Review/Edit Control Matrix 61
7.5.1 Review Entries 61
7.5.2 Edit Entries 62
7.6 Defining a Control Matrix Entry 63
7.6.1 Input Definitions 63
7.6.2 Output Definitions 69
7.6.3 Completion of New Entry 75
7.7 Disablement/Enablement Function 76

iv
XLS80e Fire Alarm Control Panels
Honeywell, Issue 9
March 2007
7.8 Extinguishing System Function 77
7.8.1 Types of Control Matrix Entry 77
7.8.2 MinimumConfiguration 77
7.8.3 Device Selection 78
7.8.4 HOLD Options 78
7.9 Logic Operation with Transfer Flags 79
7.9.1 Example Logic Operations 79
7.10 Print Control Matrix 81
8 Change Passcode 82
8.1 Introduction 82
8.2 How to Change a Passcode 83
9 Time-of-day Programming 85
9.1 Time-of-day Program Editing 85
9.2 Manual Override 87
9.3 DISABLEMENT and
ENABLEMENT Override 88
9.4 MULTI Thermal-Only Mode 89
9.5 Link to Day/Night Switch 89
10 Setting the Clock 90
11 Panel Settings 91
11.1 Internal Buzzer Options 91
11.2 LED ‘Blinking’ Mode 92
11.3 Number of LOOPS on Panel 93
11.4 Pulsing Sounder Modes 94
11.5 Walk Test Options (MCP/Sounder) 94
11.6 Automatic Test Options 95
11.7 Disablement Options 95
11.8 Loop Options 97
11.9 Panel Functions 97
11.10 Access Level for MUTE BUZZER etc. 98
11.11 Unlatched Non-alarm Input Logging 98
11.12 Relay Circuits SILENCE Option 99
11.13 Mains/PSU Fault Delays 99
11.14 LCD Backlight ‘On’ Duration 100
11.15 Blank Lines Between Printed Events 100
11.16 Isolated RS232 Port Set-up 101
11.17 Diagnostic RS232 Port Set-up 102
11.18 Remote Fire Output Options 103

v
XLS80e Fire Alarm Control Panels
Honeywell, Issue 9
March 2007
11.19 Day/Night Modes Configuration 104
11.20 Extinguishing System 105
11.21 Alarm Coincidence 106
11.22 Network Settings 107
11.23 Thermal Alarm Verification Time 107
12 User Menu at Level 3 Access 108
12.1 Control Output Tests 108
12.1.1 CMXModules 109
12.1.2 Local Sounder Circuits 110
12.1.3 Relay Circuits 110
12.1.4 Virtual Output Points 111
12.1.5 Loop Sounders and Boosters 111
12.2 Bad Poll Log 112
12.3 Display Active Control Matrix Rules 112
12.4 Unconfigured Devices Scan Menu 112
12.4 Commissioning Mode for MCS Sensors 113
13 Sensitivity and Alarm Delay
Recommendations 114
13.1 Analogue Sensors Sensitivity 114
13.2 Analogue Device Verification 114
13.3 Module Delays 115
14 Master/Slave Network 116
14.1 Introduction 116
14.1.1 Number of Stations on Network 116
14.1.2 Number of Zones on Network 117
14.1.3 Information Distribution via Network 118
14.2 Network Configuration Procedures 119
14.2.1 Station Type 120
14.2.2 THIS Panel 121
14.2.3 Associate Repeaters with Panel 122
14.2.4 Completion of Network Configuration 122
14.3 Print Network Configuration 122
15 Virtual Point Configuration 123
15.1 Virtual Output Points 123
15.2 Virtual Input Points 124
15.3 Virtual Output Backup Sounder 124

vi
XLS80e Fire Alarm Control Panels
Honeywell, Issue 9
March 2007
Appendix 1
Upgrading the Panel Software A1-1
Appendix 2
Available Loop Device Types A2-1
Appendix 3
XLSNET Network Configuration A3-1

1 Honeywell, Issue 9
March 2007
XLS80e Fire Alarm Control Panels
1 Introduction
Thismanualprovidesrecommendedprocedures
for the successful configuration of a complete
HoneywellXLS80eSeriesintegratedFireControl
System (including repeater panels). The
procedures also apply for XLS80e Series
stand-alone Fire Control units.
The XLS80e Series intelligent fire alarm
controllers are designed for use with
Honeywell’s range of addressable analogue
sensors, control and monitoring modules and
addressable call points. A unique signalling
protocol is used, with digital address and
control signals and analogue pulse width
monitoring for the reply data from devices.
Theserial communications interface operates
under RS485 protocol. It enables the
connection between control panels and
repeaters.
1.1 Associated Documents
Thismanual shouldbe readinconjunctionwith
the following documents:
a. XLS80e Series Installation &
Commissioning Manual
b. XLS80e Series Operating Manual
(ref. 997-474-000-x).
1.2 System Design and Planning
It is assumed that the system, of which the
XLS80eSeries firecontrol equipment isa part,
has been designed by a competent fire alarm
system designer in accordance with the
requirementsofEN54 Part14,BS 5839Part 1:
1988and anyother localcodes of practicethat
are applicable.
Be aware that....
This manual is not intended to be a fire
detectionsystem designguideandshouldonly
be used by (or under the supervision of) a
qualified system design engineer.
Some features of the XLS80e Series control
panelmay,if usedinappropriately, contravene
the requirements of EN54. Where there is a
possibility of such an occurrence, a suitable
warning is given with brief details of the EN54
requirement. A typical EN54 non-compliance
warning is illustrated at left.
EN54-2: 13.7
Maximum of 512
Sensors and/or MCPs
per panel unless
ELIBs are used

2Honeywell, Issue 9
March 2007
XLS80e Fire Alarm Control Panels
1.3 Glossary of Icons
Throughoutthis manual, and the otherrelated
XLS80e Series manuals, a number of icons
are used in the illustrations to help clarify, or
simplify, particular configuration procedures.
The following icons are used to advise or
indicate:
a. DO follow the recommended procedure or
method.
b. DO NOT use this procedure or method.
c. Inspection of an item or sub-assembly is
required at this point.
d. Following a defined process meets the
required approval/inspection criteria or
standards.
e. Followinga definedprocess doesnot meet
therequiredapproval/inspection criteria or
standards.
f. Additional items to be considered.
g. This icon placed next to a pushbutton
requires you to press it while configuring
the panel. Where two or more icons are
used, a number may be placed on or near
eachhand toindicate theorderofselection:
1 coming before 2.
h. Activityprocess step - flowarrow for single
action or iterative actions.
i. Leaderarrow- usedwith activityprocesses.
j. Sounder operating/Sounder not operating
or silenced.
k. Internal buzzer operating/not-operating or
silenced.
l. Digital clock timer - press and hold the
applicablepushbuttonfor thetime indicated.
00:00:03

3 Honeywell, Issue 9
March 2007
XLS80e Fire Alarm Control Panels
m. Mains power connected and switched ON.
n. Panel batteries power connected/
disconnected.
o. Manual Call Point (MCP)/Sensor.
p. Access 3A passcode entry requested to
continue with selected panel configuration
action (access 2 & 3 shown with three
asterisks).
q. IBM-compatible Personal Computer (PC)/
laptop.
r. Loop device address switch.
1
22
33
4455
66
77
81 8
009 9
230 V AC
50/60 Hz
Access 3A
*****