Honeywell CF3680 User manual

CF3680 2D Imager Module
For Customer-Facing Designs
Quick Start Guide
Aller à www.honeywellaidc.com pour le français.
Vai a www.honeywellaidc.com per l'italiano.
Gehe zu www.honeywellaidc.com für Deutsch.
Ir a www.honeywellaidc.com para español.
日本語 : www.honeywellaidc.com をご覧ください。
如要到中国 www.honeywellaidc.com（简体）。
查看繁体版请登陆 www.honeywellaidc.com
한글 www.honeywellaidc.com 로이동합니다 .
CF3680-EN-QS-01 Rev B
2/17

What is the CF3680 2D Imager Module?
The CF3680 is a 2D imager module designed to be integrated
into fixed mount enclosures, such as a self-service kiosk. It
includes:
• N3680 scan engine
• USB interface (USB-B connector)
•Exitwindow
• Movement detector used to start a reading session
• User feedback pins
Required Accessories
• Standard USB-A to USB-B cable
Additional Documentation
The following documents are available for the CF3680:
• CF3680 Installation Guide
• N3680/CF3680 User Guide
These documents are available from your local Honeywell OEM
representative.

CF3680 Front View
Mounting
holes (x4)
Exit
window

CF3680 Back View
Movement
detector
Ribbon cable
sensor to PCB
USB-B
connector
Distance selection
switch
User
feedback
pins
Scan
engine
Ribbon cable
engine to PCB

PCB View
1
2
1
6
1
5
1
Flex connector
to scan engine
Flex connector
to movement detector
USB-B
connector
User feedback
pins
Distance selection
switch

Connecting the CF3680 to a Host
By default, the CF3680 is in USB PC Keyboard interface.
1. Connect a standard USB cable (standard USB-A to USB-B)
to the CF3680 and to the USB port on the host.
2. Power-up the host.
3. Verify that the CF3680 is on by presenting a bar code in
front of the scan window. The white LED should turn on and
read the bar code.
Note: The CF3680 does not beep to indicate a good read unless
this has been setup by the user with the user feedback pins.
See the CF3680 Installation Guide for more details
(available from your local Honeywell OEM representative).

Distance Selection Switch
Use this switch to select the range to be used to detect an object
and trigger the scan engine. The distance is measured from the
outside of the exit window.
• Position 1—0 to 10 cm (4 in)
• Position 2—0 to 20 cm (8 in)
• Position 3—0 to 30 cm (12 in)
Note: Only position 1 is indicated on the PCB.
2
1
6
1
5
1
Position

Configuration
You can configure your scanner two ways:
• Reading configuration bar codes
• Using the EZConfig Cloud for Scanning tool
Configuration Bar Codes
Scan configuration bar codes to set up your scanner. All avail-
able configuration bar codes are available in the N3680 User’s
Guide. Contact your local Honeywell OEM representative for
more information.
EZConfig Cloud for Scanning Tool
Use the EZConfig Cloud for Scanning tool to configure your
scanner online:
1. Go to the Honeywell web site at www.honeywellaidc.com
2. Click on the Browse Products tab. Under Software, select
Device Management.
3. Click on EZConfig Cloud for Scanning.
4. Scroll to the bottom of the page and click on Register for
free access now to sign up.

Basic Setup
Here are some basic menu bar codes that may be useful for test-
ing. For more setup options see the N36810/CF3680 User
Guide (available from your local Honeywell OEM representa-
tive).
Note: The * symbol indicates the default value.
Interface
For USB serial interface, you must install the USB driver before
connecting your scanner. Contact your local Honeywell OEM
representative to get the latest USB driver.
USB Serial Interface
USB PC Keyboard *

Keyboard Country Layout
The default keyboard is United States.
French
German
Italian
All Symbologies
All Symbologies On
All Symbologies Off