Honeywell UCIP-GPRS User manual

UCIP-GPRS
HLSI-MA-192_05
Honeywell Life Safety Iberia, S.L. reserves the right to do any change in this information without notice.
For accurate and updated information go to www.honeywelllifesafety.es
Read carefully the product manual before to install this material.
The SMB-T enclosure is designed to be installed on
a Surface and inside some devices by using
described holes:
1- Surface mounting: Install the enclosure in the wall close to the
panel by using holes marked as (1).
2- Conventional panels NFS, VSN2 y ESS: Open the panel box
enclosure and remove the left Touch Display or user label plate.
Install the box under the panel mains connector. Fit the box in
the panel back box by the holes marked as 2) and slightly slide it
downwards.
3- Fit the UCIP Communicator in the SMB-T en closure by the 4
screw holders marked 3).
Installation
1
2
4
SMB-T Enclosure installation
3
Connections
Standard cable holes
Settings
Cut the necessary holes in the SMB-T enclosure
1- RS-232 Port or AUX Port (Panel cable link)
2- RJ45 Ethernet port (Commissioning and Network)
3- GPRS antenna (UCIP GPRS only)
4- 24Vcc External power
Connect needed cables as below:
STATUS LEDS
Ethernet Network
RJ45
RS232 / TTL* Serial port
UCIP Uart1
PC Conf.
DB9
DXc/ID3000
RS232 (ISO232)
ID60
RS232
VSN&NFS
TTL*
RX
3
TX
2
2
TX
2
RX
3
3
GND
5
0V
5
4
AUX.Port.*
Jp3 Jp4
RS232 Config.
The UCIP/GPRS can be configured by Ethernet port with RJ45
network cable El UCIP/GPRS or by RS232 serial port (cable not
provided), with it’s config tool, Hyperterminal or Telnet
By default it has the following serial port and IP settings:
Default Serial P. UCIP: Default IP address: 192.168.0.100
RS232: 9600 Baud Mask: 255.255.255.0
No parity Gateway:192.168.0.1
Config. Port:23
1- To configure UCIP via RS232 port, make the cable: RS232-PC Conf.DB9
2- To configure UCIP via ETHERNET, Configure your PC in the sane IP
range as the UCIP: WindowsStartControl PanelNetwork center 
Local area connectionchange adapter settingsProperties
Prot.Int(IPv4)PropertiesAlternative IP config:
i.e.IP:192.168.0.50, Mask 255.255.255.0, Gateway 192.168.0.1
UCIP Console tool
3-Abra la consola de config. deUCIP o el Hyperterminal de Windows y
seleccione Puerto Serie y el puerto o TCP IP con la IP del UCIP puerto 23:
- Puerto Serie Com: 9600 bds,0,None,None
- Puerto TCP IP Client: 192.168.0.100, Puerto 23
Consola UCIP:
4- Para acceder a Configuración , con el cursor en la ventana de conexión
presione 3 veces la tecla "ESC" de su PC e inserte la clave "1234"
Configuration Console / Hyperterminal
ETHERNET UCIP local IP and Port ETHERNET
TCPIP [local IP] [network Mask] [Gateway] [dhcp on/off] IP UCIP Config.:
i.e. 192.168.0.100,Mask:255.255.255.0,Gateway:192.168.0.1;DHCP:off
>TCPIP 192.168.0.100 255.255.255.0 192.168.0.1 off 
>OK: Operation completed
CONFIG [Port] [Parameter] : Set IP port i.e..5000
>CONFIG TCPSERVER 5000 
>OK: Operation completed
Note: In TG supervisor, set in panel config. Link : TCP/IP, permits multiple link
7
Config GPRS Network (i.e.FireIMT)
PIN [SIM PIN] : PIN of SIM card..
-Recommended to remove SIM PIN in a celular pone to
avoid lock it on error.
Ej. PIN XXXX. SIM must be placed to check the PIN
>PIN XXXX 
>OK: Operation completed
GPRS [APN mobile network][User][Password]
GPRS wlapn.es honeywell honeywell 
>OK: Operation completed
5
6
9
SMS Message sending to user Mobil
UCIP GPRS can send SMS messages to a SMS compatible
Alarm Receiver or up to 2 user mobile telephones.
SMS[SMS Receiver phone][MOBILE1][MOBILE2]
ej. SMS sending to user mobile phone [phone]
>SMS NONE 699887766 NONE
>OK: Operation completed
2
1
1
Panel Port settings:
ID3000: Level 3 :6)Config. 6) Panel Settings 17) Isolated RS232
Port setup: Integration protocol, 9600 baud, 11A. Half Duplex.
Requires 24Vdc.
ID60: 5)Config.1)Config.4)Peripherals2)RS232: Integration. Half
Duplex.
Requires 24Vdc.
DXc: 5)Actions7)Commission1)General Options2ndSerial Port:
TTP,9600.
Requires 24Vdc.
VSN / NFS / RP1r (TTL*): *Requires to change Jp3 and Jp4 in UCIP.
Power (+) by AUX port (VSN / NFS / RP1r)
1
1
1
2
110
mm
135
mm
79m
m
97m
m
1
1
2
2
3
3
3
3
RS485 Port
GND
B -
A+
RS 232:
ID / DXc …
TTL*:
Vision/NFS
RS232*
Port.
+
% GPRS GPRS Syst RX TX F.CRA F.link Out 1 Out 2
External Power
24Vdc
-+
GPRS antena
GND
TX
RX
+ 23 -
SIM
1)Select Port type: TCP/IP Client
2)Type the UCIP IP and Port 23
3)Clic on connection
>Type here your
command
1234
4) TYPE CONFIG COMMANDS, as described in steeps 6
to 9, including your data (red color in the examples),
separate and press ENTER to send it.
8
Central Receiver Alarm Center CRA IP
UCIP GPRS permits up to 2 IP address to send system states
to an IP compatible Receiver CRA1 and CRA2
CRA1 [CLIENT#][IP CRA][IP PORT][Alive T]
[Password][Channel: ETH+GPRS;ETH;GPRS]
i.e. Client # AAAAAA, Receiver IP 192.168.1.100 and port
10001, Alive test time 60seg, encrypted password 111111 and
send only by GPRS channel:
>CRA1 AAAAAA 192.168.1.100 10001 60 111111 GPRS
>OK: Operation completed
CRA2 [CLIENT#][IP CRA][IP PORT][Alive T][Password]
[Channel_Send:GPRS+ETH;GPRS;ETH;_FAIL;_EVER]
i.e. Client # AAAAAA, Receiver IP 192.168.1.102 and port
10002, Alive test time 60seg, encrypted password 111111,
send only by GPRS channel and send on CRA1 fail :
>CRA1 AAAAAA 192.168.1.102 10002 60 111111 GPRS_FAIL
>OK: Operation completed
Panel connection
Install de communicator as indicated above closet o panel linking the panel
communication port to the corresponding on the UCIP as described in the
table on step 3). Connection examples:
1234
RS232
RS 232 (Panel) to 1+2 UCIP
JP3 y JP4 UCIP
TTL mode
Panel VSN/RP1r/Supra
ISO232 ID3000/DXc
ISO232 (Panel) to 1 UCIP
JP3 y JP4 UCIP RS232 mode
24V external required
0V TX CTS RX RTS
DB9 (ID60)
3
4
2
1
UCIP GPRS
Honeywell
Stick the provided label in the
enclosure cover gap oriented with
the LEDs window upwards as in
the figure.

UCIP-GPRS
HLSI-MA-192_05
Honeywell Life Safety Iberia, S.L. reserves the right to do any change in this information without notice.
For accurate and updated information go to www.honeywelllifesafety.es
Read carefully the product manual before to install this material.
Technical features
UCIP / UCIP GPRS Default Settings
Status LEDs:
ALRM1
DL1-RED
- EXISTING DATA WITH CRA
ALRM2
DL2 RED
- EXIXTING DATA WITH PANEL
ALRM3
DL3-RED
-GPRS BIDIRECTIONALITY ACTIVE
ALRM4
DL4-RED
-TCP/IP BIDIRECTIONALITY ACTIVE
BLINK
DL5-GREEN
SOFTWARE WORKING
ON: Powered inactive process
Slow blinking : Process running OK
Off: Inoperative Process
COBER
DL6- BICOLOR
GSM Coverture
- GREEN MAXIMUM COVERTURE
- ORANGE MEDIUM COVERTURE
- RED LOW COVERTURE
- BLINK GPRS SERVER CONNECTED
TX MOD
DL7-GREEN
GSM MODEM CONNECTED
GPRS / GSM activity
ON: Modem Active(Calling)
IND01
DL9 –GREEN
OUTPUT 1 STATE ( Off means CRA link failure , after 5 retries)
IND02
DL8 - GREEN
OUTPUT 2 STATE (Off means Panel link fault)
TECHNICAL FEATURES:
Power
12 a 30 Vdc (not polarized) external or via Aux port
Current
45mA min / 150mA max.
Communication Ports
1 x RS232 (Rx,Tx GND from 1200 to 115200 Bds)
1 x Ethernet (ADSL, LAN, etceteras...)
1 x Modem GSM (GSM, SMS, GPRS)
1 x I2C double connector and power
1 x RS485
Configuration
Terminal console commands / Telnet over Ethernet and GPRS. Permits SMS message commands.
Serial port 232
Rx,Tx y GND. Configurable speed and parity (1200 to 115200 Bds)
Compatible Panels with SMS or Contact ID
NFS Supra, Vision Plus, Vision 2Plus, ID50, ID3000 and DXC CONNEXION
CRA Protocol and security
Double channel de transmission over Ethernet and GPRS
Connectivity checking (stay alive) and bidirectionality.
Ademco Contact ID protocol IP/GPRS to CRA over ALWON 128 encrypted AES128 compatible
protocol. Communicator switch security and config password key.
IP Connectivity
DNS compatible, DHCP and dynamic IP (IP update by alive string)
Firmware update
Via RS232 or GPRS by UCIP Consola Tool
Dimensions (w.o. box)
86mm height x102mm width x25mm depth
Enclosure Dimensions
102mm height x143mm width x39mm depth
Approvals
EN50136 SPT 1-6, Type X/Y
REQUIRED DATA TO CONNECT THE DEVICE:
For Ethernet:
UCIP IP in local network
Local Mask + Gateway
For GPRS:
APN GPRS net name
User
Password
SIM card PIN (or remove)
To a CRA:
Client Number/code
CRA IP
IP port
ALIVE time
Encryptation password
Information for the CRA
UCIP Production Serial #
S/N:
Protocol UCIP
Honeywell R TCPv9.0.2;R20;Lopez Bellov9.0.2 Receiver - Protocol Alwon 128 (Contact ID)
INFORMACIÓN DE PRODUCTO:
The UCIP and UCIP-GPRS Communicator permits to connect panels via IP by Ethernet or/and GPRS.
UCIP/UCIP GPRS is compatible to connect to an IP Central Receiver Alarm center the Honeywell Fire Alarm Panels: Notifier:ID3000,
ID50, NFS Supra; Morley-IAS: CONNEXION, VSN-2Plus and ESSER: ESS-2PLUS.
UCIP-GPRS is shipped to be connected to the Honeywell GPRS APN to be linked to the FireIMT online server and associated services.
When UCIP is connected to he compatible panels it recognizes the panel protocol and its serial port is automatically set to communicate
with it. SIM card is detected at the device start up to start the GPRS modem. In some panels it is necessary to configure the Integration
protocol.
The UCIP SERIAL NUMBER is different on each device and must be indicated to the Central Alarm Receiver center to configure client.
DEFAULT SETTINGS:
Default settings includes:
-Serial Port to Fire panel link : 9600 Baud, no parity, to panel port RS232 or TTL (depending on port Jumpers).
-GPRS Network: SIM is required, configured to connect to Fire IMT server (port 5000) Requires SIM card provibed by Honeywell and
client settings)
-ETHERNET to remote link by port 5000 (TG):
IP UCIP: 192.168.0.100, Mask 255.255.255.0, Gateway 192.168.0.1, Ethernet port: 5000
-CRA: Requires CRA IP address configuration, by default sends System Alarm and Fault by zones state.
-SMS: SIM is required. No phone is configured: Sends complete information and device labels configured in the ID and DXc panels.
.
Configuration checking:
The device configuration can be checked by using the CONFIG command connected to device in the configuration mode.
>config
SERIAL NUMBER- xxxxxxx
CRA1- Suscriber:, IP:0.0.0.0, Puerto:0, Alive:0, Key:, Channel:GPRS+ETH
CRA2- Suscriber:, IP:0.0.0.0, Puerto:0, Alive:0, Key:, Transmission: On fail of CRA 1; Channel:GPRS+ETH
SMS/DAY- Without limit ,Send: 0
TCP/IP- MAC:00-04-A4-01-00-05, IP:192.168.0.100, Mask:255.255.255.0, Gateway:192.168.0.1, DHCP:ON, Host:E20_5
TELNET- Port:23
UART1- Speed:9600, Parity:NONE
I2C- Local Address:40, Remote Address:0
RS485-Local Address:3, Remote Address:0
UDP-Address:0.0.0.0, Port:1
TCP SERVER-Port:5000
TCP CLIENT-Address:0.0.0.0, Port:1
GPRS- wlapn.com, User: honeywell, Password: honeywell
GPRS SOCKET-NONE
GPRS SERVER- Local Address:0.0.0.0, Local Port:5000
SMS ALARM- CRA:, User1:, User2:
Configuration commands:
CRA1 ACCOUNT IPADDRESS PORT ALIVE KEY: Configure the CRA account number, central IP,key and Alive period
CRA2 ACCOUNT IPADDRESS PORT ALIVE KEY TRANSMISSION: Configure the CRA2 account number, central IP,key and Alive period
CONFIG PORT PARAM1 PARAM2:Config Port or display configuration
EVENT EVENT CODE: Config ContactID event codes
EVENTNAME EVENT NAME: Config event name
EXIT :Exit program console
FAULT FAULT CODE: Config fault codes
GSM Modem GSM Communication console
GPRS APN USER PASSWORD:Config GPRS network
INI :Reset configuration (no borra IP ETH)
OUT OUTPUT STATUS TIMER: Enable or disable digital output
PIN PIN: SIM PIN settings
RESET System Reset, Cold start
SMS CENTRAL_PHONE USER_PHONE1 USER_PHONE2 MAXSMS: SMS parameters configuration
TCPIP ADDRESS MASK GATEWAY DHCP:Config TCP/IP
ZONE ZONE SENSOR MODULE FAULT DISABLE:Config zone event codes
ZONENAME ZONE NAME: Config zone name
TCPIP INI : Set default IP. The INI command does not change device IP.
CRAX OFF: Erase CRA X(1 o 2) settings
Note: Before to install the system, check and read carefully device
and connected panel manuals and don’t make any action before to understand them.
Product Manuals
download: