Honeywell Temaline TK-S014 User manual

TK_S014 – Installation Manual i
Installation Manual
Temaline
TK_S014 (RTU A08)

ii TK_S014 – Installation Manual
Document
Release
Revision
Date
800-22713
1.1
f
October 2016
Notice
This document contains Honeywell proprietary information. Information contained herein is to be used solely
for the purpose submitted, and no part of this document or its contents shall be reproduced, published, or
disclosed to a third party without the express permission of Honeywell Europe.
This document and the data in it shall not be duplicated, used or disclosed to others for procurement or
manufacturing, except as authorized by and with the written permission of Temaline, Inc.
The information contained in this document or in the product itself is the exclusive property and trade secrets
of Temaline, Inc. Copyright laws of the United States protect all information in this document or in the
software product itself.
While this information is presented in good faith and believed to be accurate, Honeywell disclaims the
implied warranties of merchantability and fitness for a purpose and makes no express warranties except as
may be stated in its written agreement with and for its customer.
In no event is Honeywell liable to anyone for any direct, special, or consequential damages. The information
and specifications in this document are subject to change without notice.
Copyright 2016 – Honeywell International Inc.
Honeywell trademarks
Tema-VoyagerTM is a trademark of Honeywell International Inc.
MIFARE® is a registered trademark of Philips Electronics N.V.
HID, iCLASS®, and Sokymat are trademarks or registered trademarks of HID Global Corporation.
LonWorks is a registered trademark of Echelon Corporation in the Unites States and/or other countries.
Any other trademarks that appear in this document are used only to the benefit of the trademark owner, with
no intention of trademark infringement.
Compliance
To obtain applicable EU compliance Declaration of Conformities for this product, please refer to our website,
https://extranet.honeywell.com. For any additional information regarding the compliance of this product to
any EU-specific requirements, please send email to [e-mail]
Single contact point and Support
Manufacturer’s single point of contact:
Honeywell S.r.l.
Via Philips, 12
20052 Monza
ITALY
For technical assistance, call your nearest Honeywell office.

TK_S014 – Installation Manualiii
TABLE OF CONTENTS
INTRODUCTION............................................................................................................................................... 5
WHAT TK_S014 (RTU A08) IS?...................................................................................................................... 5
RTU A08 TOGETHER WITH OTHER TEMALINE DEVICES....................................................................................... 5
Readers..................................................................................................................................................... 5
Interactive Terminals................................................................................................................................. 5
Compositions with phased out devices..................................................................................................... 6
RELATED DOCUMENTATION .............................................................................................................................. 7
PREPARING FOR INSTALLATION................................................................................................................. 8
CONTENTS OF THE KIT ..................................................................................................................................... 8
MOUNTING TOOLS............................................................................................................................................ 8
SYSTEM ARCHITECTURE .................................................................................................................................. 8
WIRING CHARACTERISTICS .............................................................................................................................. 9
Power supply wire..................................................................................................................................... 9
LONWORKS

Data Cables ...................................................................................................................... 9
Input wires............................................................................................................................................... 10
Readers wires......................................................................................................................................... 10
MOUNTING THE DEVICE............................................................................................................................... 12
MOUNTING ON DIN/OMEGA RAIL..................................................................................................................... 12
MOUNTING THE DEVICE INTO ENCLOSURES...................................................................................................... 12
CLOSING THE RTUA08 MODULE.................................................................................................................... 13
WIRING OPERATION..................................................................................................................................... 14
ELEMENTAL DETAIL ....................................................................................................................................... 14
CONNECTION OF POWER SUPPLY CABLES........................................................................................................ 14
CONNECTION OF THE LONWORK CABLES......................................................................................................... 14
Daisy chain connection (BUS)................................................................................................................ 15
Free topology connection (STAR)........................................................................................................... 15
Lonwork cables connection..................................................................................................................... 16
CONNECTIONS OF READER CABLES ................................................................................................................ 16
CONNECTING THE DOOR................................................................................................................................. 17
Door Connection (Using +14V Internal Power Supply) .......................................................................... 17
Door Connection (Using +V External Power Supply) ............................................................................. 18
SETTING THE NORMALITY VALUE FOR THE OUTPUTS......................................................................................... 18
RULES FOR INSTALLATION IN HARSH ENVIRONMENT ......................................................................................... 18
General rules........................................................................................................................................... 19

iv TK_S014 – Installation Manual
Cables rules............................................................................................................................................ 19
ACTIVATION................................................................................................................................................... 20
CHECKING THE COMMUNICATION BETWEEN RTUA08 AND TEMASERVER.......................................................... 20
COLLECTING DEVICE INFORMATION................................................................................................................. 21
TECHNICAL DATA......................................................................................................................................... 22
REGULATION COMPLIANCE........................................................................................................................ 24
CE COMPLIANCE........................................................................................................................................... 24
FCC NOTICE................................................................................................................................................. 24
CANADIAN AND UNITED STATES UL LISTED ..................................................................................................... 24
ROHS COMPLIANCE....................................................................................................................................... 25
WEEE COMPLIANCE ..................................................................................................................................... 25
CHINA ROHS DECLARATION........................................................................................................................... 25
MEANING OF GRAPHICAL SYMBOLS USED ............................................................................................. 26

TK_S014 – Installation Manual 5
INTRODUCTION
What TK_S014 (RTU A08) is?
TK_S014 is a Temaline device acting as a single door controller.
It can manage up two third party Wiegand readers (on the two sides of the doors), the inputs / outputs used
for the management of such readers (led and buzzers) and the inputs / outputs needed for the management
of the door (door state, REX button, lock commands).
The device can be used to manage these two door scenarios:
•Reader on one side of the door, REX button on the other
•Readers on both the door sides
Be aware that, even if the device can manage two third party Wiegand readers, it cannot
manage two different doors. When the device manages two readers the only allowed
configuration is to have them on the two sides of the same door
The device needs to be wired by mean of a Lonwork connection to a Temaline TemaServer device that acts
as a controller.
RTU A08 together with other Temaline devices
The RTU A08 device can be used together with other Temaline devices to compose a TemaKey; there are
different TemaKey types that differ from the type of Human Machine Interface they have.
Each TemaKey consists of one or more RTU modules that must be positioned and connected to their
respective wall attachment frames (RTU-Sxx) as indicated in the table below.
Here below the list of TemaKeys can be composed using the RTU A08 device and their characteristics.
Readers
Code Composition Notes
TK_S014
RTU-A08 + third party Wiegand reader Weight=0.2Kg Power=0.9W
Current=70mA
(Excluding reader current)
RTU-A08 + 2 third party Wiegand
readers
Weight=0.2Kg
Power=0.9W
Current=70mA (Excluding readers current)
The 2 readers are on the same door one in
entry and one in exit direction
Interactive Terminals
Code Composition Notes
TK_D214 RTU-A08 + third party Wiegand reader +
RTU-C02 + 2 RTU-S01
Weight=1.15Kg
Power=6.2W
Current=450mA (Excluding reader current)
RTU-A08+ 2 third party Wiegand readers
+ RTU-C02 + 2 RTU-S01
Weight=1.15Kg
Power=6.2W
Current=450mA (Excluding readers current)
The 2 readers are on the same door one in
entry and one in exit direction

6 TK_S014 – Installation Manual
Compositions with phased out devices
Note: These compositions are done including some phase out devices cannot anymore be purchased. This
list is left here just for maintenance reference.
Terminals
Code Composition Notes
TK_D014 RTU-C01 + RTU-A08 + RTU-S01 + third
party Wiegand reader
Horizontal mounting.
Weight=0.65Kg
Power=2.8W
Current=210mA (Excluding reader current)
RTU-C01 + RTU-A08 + RTU-S01 + 2 third
party Wiegand readers
Horizontal mounting.
Weight=0.65Kg
Power=2.8W
Current=210mA (Excluding readers
current)
The 2 readers are on the same door one in
entry and one in exit direction
Terminals with Keyboards
Code Composition Notes
TK_T014 RTU-C01 + RTU-T01 + RTU-A08 + 2 RTU-
S01 + 1 third party Wiegand reader
Horizontal mounting.
Weight=1.05Kg
Power=3.3W
Current=240mA
(Excluding reader current)
RTU-C01 + RTU-T01 + RTU-A08 + 2 RTU-
S01 + 2 third party Wiegand readers
Horizontal mounting.
Weight=1.05Kg
Power=3.3W
Current=240mA (Excluding reader current)
The 2 readers are on the same door one in
entry and one in exit direction
Interactive Terminals with Keyboards
Code Composition Notes
TK_T214 RTU-C02 + RTU-B01 + RTU-A08 + 2 RTU-
S01 + 1 third party Wiegand reader
Horizontal mounting.
Weight=1.4Kg
Power=6.6W
Current=480mA (Excluding reader current)
RTU-C02 + RTU-B01 + RTU-A08 + 2 RTU-
S01 + 2 third party Wiegand readers
Horizontal mounting.
Weight=1.4Kg
Power=6.6W
Current=480mA (Excluding reader current)
The 2 readers are on the same door one in
entry and one in exit direction

TK_S014 – Installation Manual7
Related documentation
Document Content
EBI Temaline Interface - Temaline Access
Control Configuration Guide Further information on the EBI Tema system, complete commissioning steps and system
configuration are included in the, which is provided
with EBI documentation package.
Temaline - installation in Harsh Environment: It is a whitepaper with Temaline system rules on this
topic.

8 TK_S014 – Installation Manual
PREPARING FOR INSTALLATION
Contents of the kit
Before you begin, unpack the shipment and check the parts list against the components in the shipment.
Your shipment should contain:
•RTU A08 device
•Support kit with the following:
o2 white resistors (392Ω 1% 1/4W)
o2 yellow resistors (1210Ω 1% 1/4W)
o2 diodes (1N4004)
o4 self-tapping screws (used to screw the device cover)
Mounting tools
The following screwdrivers are required for the installation:
•One small flat screwdriver
•One 0-1 flat head screwdriver
System Architecture
This is a typical system architecture in which the RTU-A08 is inserted:
Figure 1RTU-A08 architecture
The devices represented are:
•TemaServer: is the controller that manages the RTU-A08. It can be both a TS AC and a TS2 device
•TemaPower: is the power supply used to supply the devices. It can be one Temaline TPU-xx device
or a third party power supply.
•Third Party Wiegand readers: are used to control the access to the door on entry and Exit direction

TK_S014 – Installation Manual9
The connections shown are:
•The Power supply connection: it connects the Power Supply device whit other Temaline devices
•The LonWorks connection: to connect the TemaServer with the RTUs
•The Input and Output are used to connect the physical door managed (lock, Door sense, REX and
others)
•The Reader connections: are Wiegand lines that connect RTU-A08 with the third party readers.
Wiring Characteristics
Power supply wire
The RTU is powered at low voltage (12VDC) by a battery-operated power supply module (RTU-Qxx). When
determining the correct size for power cables, refer to the table below. (Voltage cable drop max = 0,7V)
Cable Length (m) = 0,7V / (I [A] load x 2 x (R [Ohm/km] /1000))
Type of cable Length (m) in relation to base load
AWG mm2Ohm/Km 100
[mA]
200
[mA]
500
[mA]
1 [A] 2 [A] 5 [A]
14 2 8.8 398 199 80 40 20 8
16 1.3 14 250 125 50 25 13 5
18 0.9 21 167 83 33 17 8 3
20 0.6 34 103 51 21 10 5 2
22 0.35 52 67 34 13 7 3 1
Table 1. Length/Capacity of Power Cables (m)
LONWORKS

Data Cables
The LONWORKSdata cable must be twisted-pair.
In a free topology configuration, the total length of the sections must not exceed 500m.
In a bus configuration, the total length of the sections must not exceed 2700m.
In a free topology configuration, activate the 51 ohm terminator by placing the appropriate jumper on the
related TemaServer device:
•For TS AC close the jumper on LonWorks plug-in.
•For TS2 close JP1 on the LonWorks MIP board.
For further details please refer to the related TemaServers Installation guides.
In a bus configuration, place two terminators (with resistance values of 100ohm 1% ½W) at each end of the
bus.
Check that the length of the LONWORKSdata cable corresponds to the norms indicated in Table 2.
Type of cable Length [m] in relation to cable capacity
AWG mm2 Ohm/Km 50nF/Km 100nF/Km 200nF/Km 500nF/Km 1uF/Km
12 3,3 5,7 2676 1892 1338 846 598
14 2 8,8 2153 1523 1077 681 482
16 1,3 14 1707 1207 854 540 382
18 0,9 21 1394 986 697 441 312
20 0,6 34 1096 775 548 346 245
22 0,35 52 886 626 443 280 198

10 TK_S014 – Installation Manual
24 0,2 85 693 490 346 219 155
Table 2. Length/Capacity of LONWORKS

Data Cables (m)
The FTT10A Echelonv1.2 User Guide recommends the cables indicated in Table 3.
Producer and Model AWG Connection to bus
-maximum total
length [m]
Connection in
free topology –
maximum node-
node length
max. [m]
Connection in free
topology –
maximum total
wire length. [m]
Belden 85102 16 2700 500 500
Belden 8471 16 2700 400 500
Level IV (twisted-pair,
typically solid and
unshielded)
22 1400 400 500
JY (St) 2x2x0.8 (4-wire
helical twist, solid
shielded)
20 900 320 500
TIA Cat5 / 900 250 450
Table 3. Recommended LONWORKS

Cables
Input wires
Use a twisted pair cable for the contacts connections.
For outdoor wiring is mandatory to use shielded cables. The cables’ shielding must be connected to the
respective ground connectors (-V).
For internal wiring without shielded cables is recommended an electrical environment where the cables are
well separated, even at short runs, especially to whom can be essentially subjected to interference.
The following table lists wire gauges and distances for Inputs.
Cable type Max distance (m)*
AWG mm2 Ohm/km
12 3.3 5.7 2193
14 2 8.8 1420
16 1.3 14 893
18 0.9 21 595
20 0.52 34 368
22 0.35 52 240
24 0.2 85 147
26 0.13 137 93
Table 4Length of Input cables
*One-volt voltage drop is considered typical.
Readers wires

TK_S014 – Installation Manual11
The wires used to connect the RTU-A08 to the reader(s) are those specified into the reader technical
specification.

12 TK_S014 – Installation Manual
MOUNTING THE DEVICE
Mounting on DIN/omega rail
The device is mounted on standard DIN/omega rail; to mount it you should follow these steps:
1. Hook the bottom of the RTU-A08 onto the upper margin of the DIN/omega Rail.
2. Push until it clips onto the rail. (See Figure 2).
CLIP
ROTATION
Figure 2. Mounting onto the DIN Rail
Mounting the device into enclosures
Often a device is mounted, together with others, inside large enclosures with DIN/omega rails that provide
enough space for access and wire.
When a device need to be mounted into a small enclosure it minimum size must follow the dimensions
reported in the next figure.
120mm Min
150mm Min
Internal
depth
80mm Min
DIN RAIL
45mm Min
CABLE ENTRANCE
Figure 3. Box with DIN Rail

TK_S014 – Installation Manual13
Closing the RTUA08 Module
To close the unit, follow these steps (see Figure 4):
•Clip the cover onto the module.
•Screw on the module cover with the 4 self-tapping screws (requires a 3mm cross-head screwdriver).
RTU-A08
Figure 4. Closing the RTUA08 Module

14 TK_S014 – Installation Manual
WIRING OPERATION
Elemental Detail
Figure 12 shows a detail of the electronic board, including the positions of the main connectors and service
elements.
Figure 5. Elemental Detail
Connection of power supply cables
The RTU A08 device must be powered with a 12V DC power supply. To determine the correct size of the
power cable please refer to Table 1. Length/Capacity of Power Cables (m)Table 1.
Figure 6Power Supply connection
Connection of the Lonwork cables

TK_S014 – Installation Manual15
It is possible to connect TemaServer and the RTU in two different ways:
•Daisy chain (also known as Bus)
•Free topology (also known as Star)
Based on the type of connection used in your plant some terminator resistors are required; if you don’t install
them the RTU A08 device will not work in a proper way.
Daisy chain connection (BUS)
The LONWORKSdata cable must be twisted-pair.
In a bus configuration, the total length of the sections must not exceed 2700m.
Check that the length of the LONWORKSdata cable corresponds to the norms indicated in Table 2.
In a bus configuration, place two terminators (with resistance values of 100ohm 1% ½W) at each end of the
bus.
Figure 7Daisy chain (BUS) connection
Free topology connection (STAR)
The LONWORKSdata cable must be twisted-pair.
In a free topology configuration, the total length of the sections must not exceed 500m.
Check that the length of the LONWORKSdata cable corresponds to the norms indicated in Table 2
In a free topology configuration, activate the 51 ohm terminator by placing the appropriate jumper on the
related TemaServer device:
•For TS AC close the jumper on Lonwork plug-in.
•For TS2 close JP1 on the Lonwork MIP board.
For further details please refer to the related TemaServers Installation guides.

16 TK_S014 – Installation Manual
Figure 8Free topology connection
Lonwork cables connection
Screw the twisted pair cable to LON-A and LON-B
The polarity of the LONWORKS®cables is not significant.
Figure 9LON cable connectuion
A very common error in Lonwork cabling is to forget to terminate the lines; this can cause a variety
of unpredictable errors in the system; so please remember to add resistors terminators on the LON
cabling!
Refer to the above chapters on the different Lonwork wiring typologies for the related terminators details.
Connections of Reader cables
Connect the shielded cables coming from the readers to the terminal screws on the RTUA08 as shown in
Figure 10. The shields must be connected directly to the main earth ground.
GND
Wiegand0
Wiegand1
LED-RED
LED-GREEN
BUZZER
+12V
READER 1
GND
Wiegand0
Wiegand1
LED-RED
LED-GREEN
BUZZER
+12V
READER 2
GND
GND
WIE0-IN1
WIE1-IN1
LED-RED1
LED-GREEN1
BUZZER1
+12VRDR
GND
WIE0-IN2
WIE1-IN2
LED-RED2
LED-GREEN2
BUZZER2
+12VRDR
EARTH
GROUND
GND
Figure 10. Cable Connection to RTU A08 Wiegand Module

TK_S014 – Installation Manual17
Connecting the door
Door Connection (Using +14V Internal Power Supply)
LONWORKS POWER
ELECTROLOCK
White
Yellow
ELECTROLOCK
White
Yellow
switch
switch
OUT1
+12LOCK
OUT2
IN1
IN2
GND GND
LON-A LON-B
GND SUPPLY IN
+12V SUPPLY IN
GND GND WIE0-IN1 WIE1-IN1 LED-RED1 LED-GREEN1 BUZZER1 +12VRDR
+12LOCK
GND WIE0-IN2 WIE1-IN2 LED-RED2 LED-GREEN2 BUZZER2 +12VRDR
GND
GND
GND
JP1 JP2
1
2
3
Figure 11. Door Connection Using +14V Internal Power Supply
Be aware that, even if the diode is already embedded in the unit, in some cases (long cable installed
near the inputs cables) may be useful to add an external diode provided with the unit close
to the relay device

18 TK_S014 – Installation Manual
Door Connection (Using +V External Power Supply)
You may power the electro lock doors using an external isolated power supply (Voltage between 10 and
28VDC).
LONWORKS POWER
ELECTROLOCK
White
Yellow
ELECTROLOCK
White
Yellow
switch
switch
OUT1
+12LOCK
OUT2
IN1 IN2
GND GND
LON-A
LON-B
GND SUPPLY IN
+12V SUPPLY IN
GND GND WIE0-IN1 WIE1-IN1 LED-RED1 LED-GREEN1 BUZZER1 +12VRDR
+12LOCK
GND WIE0-IN2 WIE1-IN2 LED-RED2 LED-GREEN2 BUZZER2 +12VRDR
GND
GND
GND
AC IN
DC OUT
Isolated
Power supply
GND
10 - 28VDC
JP1 JP2
1
2
3
Figure 12. Door Connection Using +V External Power Supply
Be aware that, even if the diode is already embedded in the unit, in some cases (long cable
installed near the inputs cables) may be useful to add an external diode provided with the
unit close to the relay device
Setting the normality value for the outputs
Jumpers JP1 and JP2 are used to set the normality value for the Output of the device. The factory setting for
the jumpers is Normally Open (NO).
•JP1 sets the normality value for the OUT 1
•JP2 sets the normality value for the OUT 2
When the jumper is set between position 2 and 3 the normality value for the related output is Normally Open
(NO). This is the factory position for the jumper.
When the jumper is set between position 1 and 2 the normality value for the related output is Normally
Closed (NC).
Rules for installation in harsh environment

TK_S014 – Installation Manual19
For complete system details on this topic please refer: Temaline - installation in Harsh Environment
whitepaper
General rules
In case of installation of the device in harsh environment apply the following rules:
•All the cables must run into an isolated and dedicated track;
•The cables must not run parallel to high voltage cables ( > 50Vac).
•Distance from high electromagnetic source must be > 10mt (an Electromagnetic source is a device
that generates high electromagnetic noise at frequency from 150Kz to 1 Ghz (tested up to 10V/m
(61000-4-6)) or Power frequency magnetic noise (tested up to 100V/m (61000-4-8)).
Cables rules
•INPUT cables (door side) – shielded to local Earth ground (Shield type: braid shield 90% coverage)
•OUT Cables (door side) – shielded to local Earth ground (Shield type: braid shield 90% coverage)
•POWER SUPPLY cables – connected to RTUQs or other PWS - unshielded
•LON cable – unshielded – twisted pair
•WEIGAND cable (reader side) - shielded to local Earth ground – length max 3mt (Shield type: braid
shield 90% coverage)

20 TK_S014 – Installation Manual
ACTIVATION
This chapter shows only the preliminary steps required for the RTU activation.
The complete configuration of the device is beyond the scope of this manual; please refer to EBI Temaline
Interface - Temaline Access Control Configuration Guide for further details on these activities.
Checking the communication between RTUA08 and TemaServer
To do this verification procedure it is required to:
•Have the RTU A08 wired with the TemaServer device that manages it through the Lonwork wire.
•RTU A08 powered and working
•The TemaServer powered and working
To check the RTU A08 communication, you can activate the device service pin using the button located
inside the module.
To do this, follow these steps:
1. Push the internal «service» button
2. The TemaServer will send a wink, in response to the service pin that will cause the yellow Led to
remain illuminated for a couple of seconds. This allows you to verify that communication to and from
the TemaServer is operational
3. Make sure that the yellow service LED is off at the end of the operation.
SERVICE-LED
SERVICE-REED
SERVICE-BUTTON
Figure 13. RTUA08 Service Elements