Honeywell HercuLine 10260A User manual

Industrial Measurement and Control
10260A HercuLine®Actuator
Installation, Operation and Maintenance
Manual
ISO 9002
62-86-25-06
Rev. 6
2/03

ii 10260A Series Actuators – Installation, Operations, and Maintenance 2/03
Copyright, Notices, and Trademarks
Printed in U.S.A. – © Copyright 2003 by Honeywell
Revision 6 – February, 2003
WARRANTY/REMEDY
Honeywell warrants goods of its manufacture as being free of defective materials and faulty workmanship.
Contact your local sales office for warranty information. If warranted goods are returned to Honeywell during
the period of coverage, Honeywell will repair or replace without charge those items it finds defective. The
foregoing is Buyer's sole remedy and is in lieu of all other warranties, expressed or implied, including
those of merchantability and fitness for a particular purpose. Specifications may change without
notice. The information we supply is believed to be accurate and reliable as of this printing. However, we
assume no responsibility for its use.
While we provide application assistance personally, through our literature and the Honeywell web site, it is
up to the customer to determine the suitability of the product in the application.
ATTENTION
The emission limits of EN 50081-2 are designed to provide reasonable protection against harmful
interference when this equipment is operated in an industrial environment. Operation of this equipment in a
residential area may cause harmful interference. This equipment generates, uses, and can radiate radio
frequency energy and may cause interference to radio and television reception when the equipment is used
closer than 30 m to the antenna(e). In special cases, when highly susceptible apparatus is used in close
proximity, the user may have to employ additional mitigating measures to further reduce the electromagnetic
emissions of this equipment.
CE CONFORMITY
This product conforms with the protection requirements of the following European Council Directive:
89/336/EEC, the EMC directive and 73/23/EEC, the Low Voltage Directive. Conformance of this product
with any other “CE Mark” Directive(s) shall not be assumed.
Industrial Measurement and Control
Honeywell
1100 Virginia Drive
Fort Washington, PA 19034

2/03 10260A Series Actuators – Installation, Operations, and Maintenance iii
About This Document
Abstract
This manual contains instructions for installation, operation and maintenance of the 10260A Series Actuators.
References
Honeywell Documents
The following list identifies all Honeywell documents that may be sources of reference for the material discussed in
this publication.
Document Title ID #
Specification 62-86-03-10
Model Selection Guide 62-86-16-17
Non-Honeywell Documents
The following list identifies select non-Honeywell documents that may be sources of reference for the material
discussed in this publication.
Title Author Publisher ID/ISDN #
Process Instrumentation Terminology ISA ANSI/ISA S 51.1 – 1879 (R1993)
Contacts
World Wide Web
The following lists Honeywell’s World Wide Web sites that will be of interest to our customers.
Honeywell Organization WWW Address (URL)
Corporate http://www.honeywell.com
Industrial Measurement and Control http://www.honeywell.com/imc
International http://www.honeywell.com/Business/global.asp
Telephone
Contact us by telephone at the numbers listed below.
Organization Phone Number
United States and Canada Honeywell 1-800-423-9883 Tech. Support
1-888-423-9883 Q&A Faxback
(TACFACS)
1-800-525-7439 Service

iv 10260A Series Actuators – Installation, Operations, and Maintenance 2/03
Symbol Definitions
The following table lists those symbols that may be used in this document to denote certain conditions.
Symbol Definition
This CAUTION symbol on the equipment refers the user to the Product Manual for
additional information. This symbol appears next to required information in the manual.
WARNING
PERSONAL INJURY: Risk of electrical shock. This symbol warns the user of a
potential shock hazard where HAZARDOUS LIVE voltages greater than 30 Vrms, 42.4
Vpeak, or 60 Vdc may be accessible. Failure to comply with these instructions
could result in death or serious injury.
ATTENTION, Electrostatic Discharge (ESD) hazards. Observe precautions for
handling electrostatic sensitive devices.
Protective Earth (PE) terminal. Provided for connection of the protective earth (green
or green/yellow) supply system conductor.
Functional earth terminal. Used for non-safety purposes such as noise immunity
improvement. NOTE: This connection shall be bonded to protective earth at the
source of supply in accordance with national local electrical code requirements.
Earth Ground. Functional earth connection. NOTE: This connection shall be bonded to
Protective earth at the source of supply in accordance with national and local electrical
code requirements.
Chassis Ground. Identifies a connection to the chassis or frame of the equipment shall
be bonded to Protective Earth at the source of supply in accordance with national and
local electrical code requirements.

2/03 10260A Series Actuators – Installation, Operations, and Maintenance v
Contents
1. INTRODUCTION ................................................................................................... 1
1.1 Product Description........................................................................................................................ 1
1.2 Applications.................................................................................................................................... 1
1.3 Features .......................................................................................................................................... 1
1.3.1 Non-contact Position Sensing (NCS) with True Shaft Position Indication ......................... 1
1.3.2 Slidewire Emulation ............................................................................................................ 2
1.3.3 Film Potentiometer ..............................................................................................................2
1.3.4 Motor Positioner Board ....................................................................................................... 2
1.3.5 Auto/Manual Switch............................................................................................................ 3
1.3.6 Self-Locking/Releasing Gear Train..................................................................................... 3
1.3.7 Motor ................................................................................................................................... 3
1.3.8 Manual Operation................................................................................................................3
1.3.9 All Position Mounting ......................................................................................................... 3
1.3.10 Field Reversible ............................................................................................................... 3
1.3.11 Customer Connections ..................................................................................................... 3
1.3.12 Warranty .......................................................................................................................... 3
1.4 Honeywell Linkage Kits................................................................................................................. 4
2. SPECIFICATIONS AND MODEL SELECTION GUIDE ........................................ 7
2.1 Introduction .................................................................................................................................... 7
2.2 Specifications ................................................................................................................................. 7
2.3 Model Selection Guide................................................................................................................. 11
3. INSTALLATION .................................................................................................. 13
3.1 Introduction .................................................................................................................................. 13
3.2 Before Starting ............................................................................................................................. 13
3.2.1 Unpacking.......................................................................................................................... 13
3.2.2 Site Selection ..................................................................................................................... 13
3.2.3 Outline Dimension Drawings ............................................................................................ 13
3.3 Mechanical Installation ................................................................................................................ 16
3.3.1 General .............................................................................................................................. 16
3.3.2 Linkage Set-up................................................................................................................... 16
3.3.3 Projecting Scale Option ..................................................................................................... 20
3.4 Electrical Installation.................................................................................................................... 21
3.4.1 General Wiring Recommendations.................................................................................... 21
3.4.2 Customer Connections....................................................................................................... 22
3.4.3 Power Connections............................................................................................................ 24
3.4.4 CE Wiring.......................................................................................................................... 24
3.4.5 0/4-20 mA, 0/1-5 Vdc Input Signal Connections .............................................................. 24
3.4.6 0/4-20 mA, 0/1-5 Vdc Feedback Signal Connections ....................................................... 24
3.4.7 Slidewire Emulator Connections ....................................................................................... 25

vi 10260A Series Actuators – Installation, Operations, and Maintenance 2/03
4. CALIBRATION PROCEDURES.......................................................................... 27
4.1 Overview ...................................................................................................................................... 27
4.2 Setting End-of-Travel Limit Switches (actuators mfd. pre-1/1/03).............................................. 27
4.3 Setting End-of-Travel Limit Switches (actuators mfd. after 1/1/03)............................................ 28
4.4 Setting Auxiliary Switches (actuators mfd. pre-1/1/03)............................................................... 30
4.5 Setting Auxiliary Switches (actuators mfd. after 1/1/03) ............................................................. 33
4.6 Non-Contact Sensor ..................................................................................................................... 34
4.7 Motor Positioner Board ................................................................................................................ 35
4.7.1 Overview ........................................................................................................................... 35
4.7.2 Available Adjustments ...................................................................................................... 35
4.7.3 ZERO and SPAN Adjustments.......................................................................................... 36
4.7.4 Fail-Safe Settings; Loss of Signal (L.O.S.) ....................................................................... 36
4.7.5 Filter Settings..................................................................................................................... 37
4.7.6 Deadband and Sensitivity Settings .................................................................................... 37
4.8 Output Board Calibration ............................................................................................................. 38
4.8.1 0/4-20 mA PWA Output Board ......................................................................................... 38
4.8.2 Slidewire Emulation .......................................................................................................... 40
4.9 Reversal of Direction (Non contact sensor) ................................................................................. 42
4.10 Reversal of Direction (Film Potentiometer) ............................................................................. 42
5. START-UP/OPERATION .................................................................................... 45
5.1 Introduction .................................................................................................................................. 45
5.2 Operations Checklist .................................................................................................................... 45
6. OTHER CONTROL FUNCTIONS ....................................................................... 47
6.1 Split Range ................................................................................................................................... 47
6.2 Master/Slave Arrangement........................................................................................................... 47
6.2.1 Basic Flow Control............................................................................................................ 48
6.2.2 Proportional Flow using Multiple Actuators .................................................................... 49
6.2.3 Split Valve Configuration.................................................................................................. 51
7. MAINTENANCE .................................................................................................. 53
7.1 Introduction .................................................................................................................................. 53
7.2 Basic Maintenance........................................................................................................................ 53
7.2.1 Main Gear Lubrication ...................................................................................................... 53
7.2.2 Spur Gear Lubrication ....................................................................................................... 53
7.2.3 Non-Contact Sensor........................................................................................................... 53
7.2.4 Motor Positioner................................................................................................................53
7.2.5 Replacing the Fuses........................................................................................................... 53
8. REPLACEMENT/RECOMMENDED SPARE PARTS ......................................... 55
8.1 Introduction .................................................................................................................................. 55
8.2 Motor Kits .................................................................................................................................... 55

2/03 10260A Series Actuators – Installation, Operations, and Maintenance vii
8.3 Idler Gear Kits .............................................................................................................................. 57
8.4 Non-Contact Sensor, Film Potentiometer, Output Board Limit/Aux Switch and CAM Kits ...... 57
8.5 Linkage Parts/Kits ........................................................................................................................ 61
8.6 Accessories................................................................................................................................... 61
8.7 Non-Contact Position Sensor Field Upgrade Kits........................................................................ 62
8.8 Honeywell Actuator Linkage Analysis Software (HAL) ............................................................. 65
8.9 Replacement Fuses (Not for Sale)................................................................................................65
8.10 Film Potentiometer Upgrade Kits ............................................................................................. 65
9. TROUBLESHOOTING ........................................................................................ 69
9.1 Introduction .................................................................................................................................. 69
9.2 Troubleshooting Procedures......................................................................................................... 69
9.2.1 Actuator Current Output does not function. ...................................................................... 70
9.2.2 Actuator Slidewire Output does not function. ................................................................... 71
9.2.3 Actuator CW/CCW operation is not correct...................................................................... 72
9.2.4 Actuator does not control to the proper position. .............................................................. 73
9.2.5 Auto/Manual Switch does not operate correctly. .............................................................. 74
9.2.6 Actuator CW/CCW Switch does not operate correctly. .................................................... 75
9.2.7 Actuator Up/Down action does not operate correctly. ...................................................... 76
10. SALES AND SERVICE ....................................................................................... 77

viii 10260A Series Actuators – Installation, Operations, and Maintenance 2/03
Tables
Table 3-1 Recommended Minimum Wire Size ____________________________________________ 21
Table 4-1 Available Adjustments ______________________________________________________ 35
Table 9-1 Observable Symptoms of Failure ______________________________________________ 69
Table 9-2 Troubleshooting Current Output _____________________________________________ 70
Table 9-3 Troubleshooting Slidewire Output _____________________________________________ 71
Table 9-4 Troubleshooting CW/CCW Operation __________________________________________ 72
Table 9-5 Troubleshooting Control Action on Actuator _____________________________________ 73
Table 9-6 Troubleshooting the Auto /Manual Switch _______________________________________ 74
Table 9-7 Troubleshooting the CW/CCW Switch __________________________________________ 75
Table 9-8 Troubleshooting the Up/Down Actuator Action ___________________________________ 76

2/03 10260A Series Actuators – Installation, Operations, and Maintenance ix
Figures
Figure 1-1 10260A Actuator ___________________________________________________________ 4
Figure 1-2 10260A Internal View _______________________________________________________ 5
Figure 3-1 Outline and Dimensions of 10261A, -62A, -64A, -66A, -67A, -68A, and -69A Actuators _ 14
Figure 3-2 Outline and dimensions of 10263A and 10265A Actuators__________________________ 15
Figure 3-3 Constant Torque Linkage ____________________________________________________ 16
Figure 3-4 Constant Torque Profile _____________________________________________________ 17
Figure 3-5 Variable Torque Linkage ____________________________________________________ 17
Figure 3-6 Variable Torque Profile _____________________________________________________ 18
Figure 3-7 Turnbuckle Linkage Kit _____________________________________________________ 18
Figure 3-8 Pipe Linkage Kit __________________________________________________________ 19
Figure 3-9 Standard 5” Crank Arm _____________________________________________________ 19
Figure 3-10 Projecting Scale Option ____________________________________________________ 20
Figure 3-11 Customer Terminal Connections (Non-contact sensor) ____________________________ 22
Figure 3-12 Customer Terminal Connections (Film Potentiometer) ____________________________ 23
Figure 3-13 Slidewire Connections _____________________________________________________ 25
Figure 4-1 Location of Auxiliary Switches _______________________________________________ 31
Figure 4-2 End of Travel Limit Switch Settings ___________________________________________ 32
Figure 4-3 Auxiliary Switch Settings____________________________________________________ 32
Figure 4-4 Location of NCS Assembly __________________________________________________ 34
Figure 4-5 Motor Positioner Board _____________________________________________________ 37
Figure 4-6 0/4-20 mA PWA Output Board _______________________________________________ 39
Figure 4-7 Slidewire Emulation Board __________________________________________________ 41
Figure 4-8 Switch Jumper for Reversal __________________________________________________ 43
Figure 6-1 Flow Diagram_____________________________________________________________ 48
Figure 6-2 Interconnection Diagram ____________________________________________________ 48
Figure 6-3 Proportional Flow Using Multiple Actuators_____________________________________ 49
Figure 6-4 Multiple Actuator Interconnection Diagram _____________________________________ 50
Figure 6-5 Interconnection Diagram ____________________________________________________ 51

x 10260A Series Actuators – Installation, Operations, and Maintenance 2/03

Introduction
2/03 10260A Series Actuators – Installation, Operations, and Maintenance 1
1. Introduction
1.1 Product Description
Honeywell's 10260A industrially rated rotary control actuators are precision engineered for exceptional
reliability, accurate positioning, and low maintenance. Designed for very precise positioning of dampers
and quarter turn valves in the power an processing industries, the 10260A performs especially well in
extremely demanding environments requiring continuous-duty, high reliability, and low maintenance.
Precise positioning of the actuator is achieved through state-of-the-art motor control and positioning
electronics. The motor starts and stops instantaneously, preventing overshoot and hunting. Positioning
repeatabililty of 0.2 % span or better is achievable for extremely tight process control to take full advantage
of modern controllers.
A no-burnout synchronous induction motor is combined with a heavy-duty precision machined output
worm gear mesh providing a responsive, low maintenance, and non-backdriving actuator. Accidental stalls
up to 100 hours can be withstood without damage to the gear train. End-of-travel limit switches are
provided as standard to prevent damage to the valve or damper and are backed up by Mechanical stops.
Honeywell electric actuators provide instantaneous response to a demand signal, eliminating system non-
linearity due to dead time. Additionally, since the actuator is electric, the costs associated with providing
and maintaining a clean, dry air supply are eliminated.
A Heavy duty cast crank arm and precision rod-end bearing is provided with each 10260A actuator. Crank
arms can be positioned at any angle on the output shaft and an adjustable radius is provided to allow
flexibility in linkage set-up.
All 10260A actuators are equipped with a manual handwheel for operation during loss of power or
installation. A local auto/manual handswitch can be provided for local operation and has an “out of auto”
contact to annunciate that condition.
1.2 Applications
Honeywell actuators have a long and respected history in the industrial actuator market. 10260A actuators
are designed for precision modulation of final control devices such as dampers, vanes, fluid couplings,
scoop tubes, fuel/air ratio valves, windbox dampers, and coal mill dampers, and quarter turn valves. The
robustness of the design serves as the basis for long-term reliability and reduced operating costs.
1.3 Features
1.3.1 Non-contact Position Sensing (NCS) with True Shaft Position Indication
Introduction
Non-contact position sensing eliminates maintenance problems and nuisance shutdowns that are common
with slidewire position sensing. The non-contact position sensor replaces the slidewire and wiper assembly
for position sensing. Once calibrated, the non-contacting position sensor requires no maintenance.
Description
The non-contact position sensing assembly consists of a position sensor, an output board, and a bracket as
shown in Figure 1-2. The position sensor “spoiler” is connected directly to the output shaft, reflecting true
shaft position. As the output shaft rotates, the sensor “spoiler” rotates and the sensing circuit board detects

10260A Series Actuators Installation, Operations, and Maintenance Manual
2 10260A Series Actuators – Installation, Operations, and Maintenance 2/03
the change in position. Sensing is accomplished by changing the magnetic field created by the coils in the
sensing circuit board. There is no contact between circuit board and spoilers.
1.3.2 Slidewire Emulation
Introduction
A truly unique feature, slidewire emulation allows direct replacement of existing three-wire control
actuators without requiring controller changes while gaining all of the advantages of the maintenance-free
non-contact sensing. This is ideal for replacement of installed actuators that cause control problems due to
slidewire wear.
Description
The slidewire emulation assembly consists of a non-contact position sensor, an output board, and a bracket
as shown in Figure 1-2. The position sensor is identical to that described in Section 1.3.1.
A potentiometric voltage from the controller is supplied to the slidewire emulation circuit. This voltage is
ratiometrically conditioned with respect to the output shaft position from 0 % to 100 % and is available to
the controller. Voltages of 1 Vdc to 20 Vdc are accepted and this device will emulate 100 ohm to 1000
ohm slidewires.
1.3.3 Film Potentiometer
Introduction
Film potentiometer position sensing eliminates maintenance problems and nuisance shutdowns common
with slidewire and wiper assembly for position sensing.
Description
The film potentiometer is connected directly to the output shaft reflecting true shaft position. The film
potentiometer is 1000 ohms over the actuator’s 90 degree travel. Other ohmic values can be accomplished
using an appropriate shunting resistor.
1.3.4 Motor Positioner Board
Introduction
The Honeywell Motor Positioner Board accepts a current input signal to provide internal closed loop
control of the position of the actuator. The Honeywell Motor Positioner makes positive position control
possible with current output controllers.
Description
The Motor Positioner operates raise/lower switch contacts (triacs) which control power to the reversing
motor in the actuator. The actuators integral Non-Contact Sensor or Film Potentiometer provide the
position feedback signal to the Motor Positioner. Input signal ranges are adjustable from 0.2 Vdc to 1 Vdc,
up to 1 Vdc to 5 Vdc. By use of an appropriate shunt resistor, controller current outputs of 4-20 mA dc, 1-5
mA dc, 10-50 mA dc, can be achieved.
Fail-safe features are also provided. On loss of input signal, the Motor Positioner may be preset to drive the
motor upscale, downscale, to a particular position, or to stop where it is. In the event of actuator NCS
failure (broken wiper) or film potentiometer broken wiper, the Motor Positioner can be set to drive the
motor fully upscale or downscale. The Motor Positioner will also accept slidewire input. For
master/follower applications, the Motor Positioner will position a “follower” actuator in accordance with a
slidewire input signal from a “master” actuator. The ratio between master and follower movement is

Introduction
2/03 10260A Series Actuators – Installation, Operations, and Maintenance 3
adjustable by means of a span control. A bias offset may also be induced between master and follower by
means of a zero adjustment. For follower operations in master-follower systems, the master actuator
retransmitting slidewire can range from 100 ohms to 1000 ohms. The Motor Positioner is a printed circuit
board that is integrally mounted in a 10260A Series Actuator terminal cover. See Figure 1-2. The terminal
cover is gasketed to provide weather resistance.
1.3.5 Auto/Manual Switch
The Auto/Manual electric handswitch with auxiliary contacts indicating an "Out-of-Auto" position is
available for local electric control.
1.3.6 Self-Locking/Releasing Gear Train
The worm gear output combination is self-locking and self-releasing and maintains position upon loss of
power. It is designed to hold greater than two times the rated output torque in a back-driving condition.
This design provides superior reliability without the maintenance associated with other self-locking and
brake mechanisms.
1.3.7 Motor
A 100 % duty cycle synchronous induction motor provides crisp and responsive movement for precise and
accurate positioning. The very low current draw during operation or in stall combined with the no-burnout
characteristics of the motor result in low maintenance, high reliability, and long life.
1.3.8 Manual Operation
A manual handwheel is provided for positioning of the actuator during power outages or initial installation.
The design of the handwheel allows for positioning of the actuator safely under full load conditions.
1.3.9 All Position Mounting
Honeywell 10260A actuators may be mounted in any orientation making retrofit in tight locations easier.
1.3.10 Field Reversible
NCS: As factory shipped, the actuator is set for counter-clockwise rotation. By changing a jumper and
switch, the actuator can be set for clockwise rotation. Re-calibration is not required.
Film Potentiometer: As factory shipped, the actuator is set for counterclockwise rotation. By changing a
switch and interchanging the film potentiometer leads, the actuator can be set for clockwise rotation. Re-
calibration may be required.
1.3.11 Customer Connections
The 10260A now has dedicated wiring terminals for ease of installation. See section 3.4.2 Customer
Connections for specific placement.
1.3.12 Warranty
The 10260A actuator warranty is effective for 30 months from the date of shipment or 24 months from the
date of installation whichever comes first.

10260A Series Actuators Installation, Operations, and Maintenance Manual
4 10260A Series Actuators – Installation, Operations, and Maintenance 2/03
1.4 Honeywell Linkage Kits
Honeywell turnbuckle and pipe linkage kits are available and are recommended to provide optimal
positioning performance. The rod-end bearing connections eliminate all linkage hysteresis giving accurate
and repeatable positioning of the final control element. Honeywell has designed a linkage analysis program
(HAL) that is used to deign linkage set-up.
Non-Contact Sensor
& Switch Cover
Crank Arm and
Rod End
A
uto/M anual
Switch
Terminal Cover
Hand-
whee l
Figure 1-1 10260A Actuator

Introduction
2/03 10260A Series Actuators – Installation, Operations, and Maintenance 5
A
uto/Manual
Switch
Output Board
Field Reversible Switch
Customer
Connections
Non-Contact
Position Sensor
Limit Switches
and
A
uxilliary Switches
Handwheel
Figure 1-2 10260A Internal View

10260A Series Actuators Installation, Operations, and Maintenance Manual
6 10260A Series Actuators – Installation, Operations, and Maintenance 2/03

Specifications and Model Selection Guide
2/03 10260A Series Actuators – Installation, Operations, and Maintenance 7
2. Specifications and Model Selection Guide
2.1 Introduction
This chapter provides the user with the specifications and the Model Selection Guide for the 10260A Series
Actuator.
2.2 Specifications
Specification – General
Physical
Weight 40 lb. (18 kg) net
Enclosure Precision machined Aluminum alloy casting, finished in light gray powder coat epoxy.
Gear train Alloy steel, high efficiency steel spur gear primary train with safety fused idler gear.
Precision ground, self locking/self releasing worm gear final mesh.
Mechanical stops To prevent over-travel
Operating Temperature –30 °C to +85 °C (–20 °F to +185 °F)
Storage Temperature –40 °C to +93 °C (–40 °C to +200 °F)
Relative Humidity Fully operable over the range of 0-99 % R.H. non-condensing
Scale 0 % to 100 % corresponding to full crank arm travel.
Crank Arm Adjustable radii (1-7/16" to a maximum of 5"). Position adjustable through 360°
rotation. Optional 12” crank arm adjustable 0-12” radii.
Output Shaft 1" diameter, 1-1/2" long is standard on 10261A, 10262A, 10264A, 10266A, 10267A,
10268A.
1" diameter, 2" long is standard on 10263A, 10265A and 10269A optional on other
models.
Rotation 900degrees between 0 % and 100 % on scale, limited by mechanical stops.
Direction of Rotation Field selectable via switch and jumper. Default = CCW (determined looking into the
shaft)
Manual Handwheel Provides a means of positioning the actuator in the event of a power failure or set-
up.
Lubrication Texaco Starplex 2 EP Grease
Fuses Bussmann GDB1.6: 1.6 Amp Fast
Littlefuse 312001: 1.0 Amp Fast

10260A Series Actuators Installation, Operations, and Maintenance Manual
8 10260A Series Actuators – Installation, Operations, and Maintenance 2/03
Physical
Output Torque/Full Travel
Stroking Time
Model #
10261A
10262A
10264A
10266A
10267A
10268A
10269A
10263A
10265A
Torque
Lb.-ft N-M
10 15
20 27
40 55
60 80
40 55
80 110
150 200
200 270
300 400
Output Shaft Speed sec/90°
@ 60Hz @ 50Hz
10 12
20 24
40 48
60 72
20 24
40 48
60 72
40 48
60 72
Electrical
Power Input 120 Vac single phase, 50 or 60 Hz
240 Vac single phase, 50 or 60 Hz
Motor Instant start/stop, non-coasting, non-burnout, continuous duty permanent magnet
synchronous induction motor. Can be stalled up to 100 hours without damage.
Motor Current = No load = full load = locked rotor
Model No.
10261A, 62A, 64A, 66A
10263A, 10265A
10267A, 68A, 69A
120 V, 50/60 Hz
0.4 A (48 VA)
1.0 A (120 VA)
0.8 A (96 VA)
240 V, 50/60 Hz
0.3 A (24 VA)
1.0 A (60 VA)
0.3 A (36 VA)
Loss of Power Stays in Place
Local Auto/Manual Switch Optional - allows local and automatic operation of the actuator.
Limit Switches Standard - Two SPDT end of travel limits rated (10 A at 125 Vac, 5 A at 250 Vac).
Auxiliary Switches Optional - Up to 4 additional SPDT switches rated (10 A at 125 Vac, 5 A at 250 Vac)
Certifications
CE Compliance 89/336/EEC EMC Directive, 73/23/EEC Low Voltage Directive.
NEMA 4 Optional
Torque Settings of Crank Arm Bolts
Clamp Bolt Standard Arm (p/n 087449) (1-7/16–5 in. adjustment): 85 lb.-ft.
Optional Long Arm (p/n 154007) (0–12 in. adjustment): 85 lb.-ft.
Rod End Bolt Standard and long arms: 30-35 lb.-ft

Specifications and Model Selection Guide
2/03 10260A Series Actuators – Installation, Operations, and Maintenance 9
Specification - Actuator with Motor Positioner Board
Electrical
Input Signals Input: 4-20 mA
1 to 5 Vdc with appropriate shunt resistor for current range
(Resistor: 250 ohms ± 0.1 % Part No.: 070756)
Input Impedance Input
4-20 mA
1-5 V with fail-safe Jumper W2
1-5 V without fail-safe Jumper W2
Input Impedance
250 ohms
10 K ohms
10 M ohms
Sensitivity 0.20 % to 5 % span adjustable (shipped @ 0.5 % span)
Hysteresis Less than 0.4 % of full scale
Linearity ±0.25 % of span
Repeatability 0.2 % span
Voltage/ Supply Stability 0.25 % of span with +10/–15 % voltage change
Temperature Coefficient Less than ±0.030 % of span per degree C for 0 °C to 50 °C
Less than ±0.05 % of span per degree C for –30 °C to 85 °C
Zero Suppression 100 % of span
Input Filter Adjustable to smooth input signal
Maximum Input Voltage 5 Vdc
Output Two triac switches for raise-or-lower motor operation. Transient voltage protection
provided.
Fail-safe operation If input signal falls below 2 % of span, there are four choices selected by a movable
jumper; stop, go full upscale, go full downscale, or go to a selected (adjustable)
position.
Isolation Input is isolated from power

10260A Series Actuators Installation, Operations, and Maintenance Manual
10 10260A Series Actuators – Installation, Operations, and Maintenance 2/03
Specification - Actuator with Output Board
Electrical
Feedback signals 0-20 mA
4-20 mA
1-5 Vdc with 250 ohm resistor ±0.1 %
0-16 Vdc with 800 ohm resistor ±0.1 %
Slidewire Emulation Provides output voltage ratiometric to shaft position and potentiometric to supply
voltage (1-20 Vdc) without a slidewire. Emulates a 100 ohms to 1000 ohm slidewire.
10 mA output maximum.
Isolation Output is isolated from power and input signal by 240 Vac
Load Requirement (4-20) Current Out — 0-1000 ohms