Honeywell PRO-2200 User manual

TD1144 rev 0801
PRO-2200
Remote Enclosure
Installation Manual
Part Number: PRO22ENC3
A division of Northern Computers, Inc.

PRO-2200 Remote Enclosure—PRO22ENC3 3Installation Guide
TT
TT
Table of Contentsable of Contents
able of Contentsable of Contents
able of Contents
Warnings and Cautions........................................................................................4
Disclaimer...........................................................................................................6
Product Liability; Mutual Indemnification................................................................6
Unpacking Procedure ...........................................................................................6
Shipping Instructions ............................................................................................6
Limited Warranty .................................................................................................7
Confidentiality .....................................................................................................7
PRO-2200 Remote Enclosure................................................................................8
Description..........................................................................................................8
Dimensions .........................................................................................................8
Conduit Knockouts...............................................................................................8
Power Supply.......................................................................................................9
LED Diagnostics...................................................................................................9
Backup Power Supply ...........................................................................................9
Cables Supplied..................................................................................................9
Maintenance .......................................................................................................9
Operating Parameters..........................................................................................9
PRO-2200 Remote Enclosure..............................................................................10
Installation Instructions .......................................................................................11
Installation Diagram 1.......................................................................................11
Installation Diagram 2.......................................................................................12
Cable Specifications ..........................................................................................13
NCI Cable Part Numbers ...................................................................................14

4 PRO-2200 Remote Enclosure—PRO22ENC3Installation Guide
Warnings and Cautions
WARNINGWARNING
WARNINGWARNING
WARNING
Before installation, TURN OFF the external circuit breaker which supplies power to the
system.
Before connecting the device to the power supply, verify that the output voltage is within
specifications of the power supply.
Do not apply power to the system until after the installation has been completed.
Personal injury or death could occur, and the equipment could be damaged beyond
repair, iftheseWARNINGSare not observed!
WARNING
Fire Safety and Liability Notice
Never connect card readers to any critical entry, exit door, barrier, elevator or gate without
providing an alternative exit in accordance with all fire and life safety codes pertinent to
the installation.These fire and safety codes vary from city to city and you must get
approval from local fire officials whenever using an electronic product to control a door or
other barrier.Use of egress buttons, for example, may be illegal in some cities.In most
applications, single action exit without prior knowledge of what to do is a life safety
requirement.Always make certain that any required approvals are obtained in writing.DO
NOT ACCEPTVERBAL APPROVALS,THEY ARE NOT VALID.
EngineeredSystems never recommendsusing the PRO-2200Series or relatedproducts
for use as a primary warning or monitoring system. Primary warning or monitoring systems
should always meet local fire and safety code requirements.The installer must also test the
system on a regular basis by instructing the end user in appropriate daily testing proce-
dures.Failure to test a system regularly could make installer liable for damages to the end
user if a problem occurs.
WARNING
EARTH groundall enclosures, for proper installation.
WARNING
Use suppressors on all door strikes. Use S-4 suppressors for installation. Engineering
Systems recommends only DC strikes.
The information in this document is subject to change without notice.

PRO-2200 Remote Enclosure—PRO22ENC3 5Installation Guide
CAUTION
IF ANY DAMAGETOTHE SHIPMENT IS NOTICED, A CLAIM MUST BE FILED WITH
THE COMMERCIAL CARRIER RESPONSIBLE.
CAUTION
Electro-static discharge can damage CMOS integrated circuits and modules.
To prevent damage always follow these procedures:
Use static shield packaging and containers to transport all electronic components,
including completed reader assemblies.
Handle all ESD sensitive components at an approved static controlled workstation.These
workstations consist of a desk mat, floor mat and an ESD wrist strap.Workstations are
available from various vendors.
NOTICE
THIS EQUIPMENT HAS BEENTESTED AND FOUNDTO COMPLYWITH THE LIMITS
FOR A CLASS A DIGITAL DEVICE, PURSUANTTO PART 15 OFTHE FCC RULES
WHEN WIRED USING METAL CONDUIT FOR THE CABLING EXTERNAL TO THE
ENCLOSURE.THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTEC-
TION AGAINST HARMFUL INTERFERENCEWHEN THE EQUIPMENT IS OPERATED
IN A COMMERCIAL ENVIRONMENT.THIS EQUIPMENT GENERATES, USES, AND
CAN RADIATE RADIO FREQUENCY ENERGY AND, IF NOT INSTALLED AND USED
IN ACCORDANCE WITHTHE INSTRUCTION MANUAL, MAY CAUSE HARMFUL
INTERFERENCETO RADIO COMMUNICATIONS.OPERATION OF THIS EQUIPMENT
IN A RESIDENTIAL AREA IS LIKELYTO CAUSE HARMFUL INTERFERENCE IN
WHICH CASETHE USER WILL BE REQUIREDTO CORRECTTHE INTERFERENCE
AT HIS OWN EXPENSE.
NOTICE
This document and the data in it shall not be duplicated, used or disclosed to others for
procurement or manufacture, except as authorized by and with the written permission of,
Engineering SystemsThe information contained in this document or in the product itself is
considered the exclusive property and trade secrets of Engineering Systems.Copyright
laws of the United States protect all information in this document or in the software
product itself.
NOTICE
Any use of this product is subject to the terms and acceptance of the Engineering Sys-
tems Software Agreement. Please request a copy from Engineering Systems, and review
theagreementcarefully.

6 PRO-2200 Remote Enclosure—PRO22ENC3Installation Guide
Disclaimer
Product Liability; Mutual Indemnification
In the event that a Customer receives a claim that a Product or any component thereof
has caused personal injury or damage to property of others, Customer shall immediately
notify Engineering Systems in writing of all such claims. Engineering Systems shall
defend or settle such claims and shall indemnify and hold Customer harmless for any
costsor damages including reasonable attorneys’ fees which Customer may be required
to pay as a result of the defective Product or the negligence of Engineering Systems, its
agents, or its employees.
Customer shall hold harmless and indemnify Engineering Systems from and against all
claims, demands, losses and liability arising out of damage to property or injury to
persons occasioned by or in connection with the acts or omissions of Customer and its
agents and employees, and from and against all claims, demands, losses and liability for
costs of fees, including reasonable attorneys’ fees, in connection therewith.
Unpacking Procedure
CAUTION
If any damage to the shipment is noticed before unpacking, a claim must be filed with the
commercial carrier.
All containers should be opened and unpacked carefully in order to prevent damage to
the contents.The following steps are used to unpack equipment in preparation for instal-
lation:
1. Open the container and remove the unit(s) and all packing material. Retain the
container and all packing materials. They may be used again for reshipment
of the equipment, if needed.
2. Inspect the contents for shortage.If items are missing items, contact the order entry
department at 800-323-4576.
3. Visually check contents. If damage is discovered, perform the following:
If shipping caused damage to the unit, a claim must be filed with the
commercialcarrier.
If any other defect is apparent, call 800-323-4576 for a return authorization.
Shipping Instructions
To ship equipment back to Engineering Systems:
1. Contactthe customerservice departmentat 800-323-4576beforereturning equipment.
Pleasehave the following available when calling:
• A description of the problem or reason for returning the equipment.
• Original purchase order number, invoice number and if the unit is under warranty.
• A new purchase order number if the unit is not under warranty

PRO-2200 Remote Enclosure—PRO22ENC3 7Installation Guide
2. Obtainthe Return Authorization Number (RMA) fromthe customer service
department at 800-323-4576.
3. Show the RMA number on all packages shipped.Packages, which are not marked
with an RMA number will be refused at the factory and returned COD.
4. Carefullypack the equipment for shipment. Use the original packing material when-
ever possible.
Limited Warranty
All Products sold or licensed by Engineering Systems include a warranty registration card
which must be completed and returned to Engineering Systems by or on behalf of the end
user in order for Engineering Systems to provide warranty service, repair, credit or ex-
change. All warranty work shall be handled through Customer which shall notify
EngineeringSystems and apply for a Return Merchandise Authorization (RMA) number
prior to returning any Product for service, repair, credit or exchange. Engineering Systems
warrants that its Products shall be free from defects in materials and workmanship for a
period of two years from date of shipment of the Product to Customer.The warranty on
Terminals, Printers, Communications Products and Upgrade kits is 90 days from date of
shipment. Satisfaction of this warranty shall be limited to repair or replacement of
Products which are defective or defective under normal use. Engineering Systems’
warranty shall not extend to any Product which, upon examination, is determined to be
defective as a result of misuse, improper storage, incorrect installation, operation or
maintenance,alteration, modification, accident or unusual deterioration of the Product due
to physical environments in excess of the limits set forth in Product manuals.THERE
ARENOWARRANTIESWHICHEXTEND BEYONDTHISPROVISION.THISWARRANTY
IS IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS, IMPLIED OR STATU-
TORY, INCLUDING IMPLIEDWARRANTIESOF MERCHANTABILITY ORFITNESS FOR
ANYPARTICULAR PURPOSE.NO REPRESENTATIONORWARRANTY OFTHEDIS-
TRIBUTOR SHALL EXTENDTHE LIABILITY OR RESPONSIBILITY OFTHE MANUFAC-
TURER BEYONDTHETERMS OFTHIS PROVISION.IN NO EVENT SHALL ENGINEER-
ING SYSTEMS BE LIABLE FOR ANY RE-PROCUREMENT COSTS, LOSS OF PROF-
ITS, LOSS OF USE, INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGESTO ANY
PERSON RESULTING FROMTHE USE OF ENGINEERING SYSTEMS’ PRODUCTS.
Confidentiality
All software, drawings, diagrams, specifications, catalogs, literature, manuals and other
materials furnished by Engineering Systems relating to the design, use and service of the
Products shall remain confidential and shall constitute proprietary rights of Engineering
Systems and Customer agrees to treat such information as confidential. Customer shall
acquire no rights in the design of the Products or the related materials except to use such
information solely for the purpose of and only during the time it sells the Products. Cus-
tomer shall not copy the design of any of the Products or use or cause to be used any
Product design or related materials for its own benefit or for the benefit of any other party.
The covenants contained in this section shall remain effective throughout the term of this
Agreement and thereafter unless specifically waived by Engineering Systems in writing.

8 PRO-2200 Remote Enclosure—PRO22ENC3Installation Guide
PW-5000 Remote Enclosure
Description
The PRO-2200 Remote Enclosure allows for a variety of system configurations. It can be
used in combination with the PRO22ENC1, for example to place modules closer to the
doors they control. Or it can be used alone to house modules for a smaller system.
This enclosure can mount two full size PRO-2200 panels (PRO22IC,PRO22IN,
PRO22OUT,PRO22R2)OR one full size panel, one PRO22R1single reader panel and one
PRO22MX8multiplexer panel.
The 2 amp power supply provides power for the modules.The battery is a 4.0 amp hour
batterycapable of providing 2.5 to 4 hours backup, depending on configuration.
Dimensions
Height:14" (0,356m)
Width:16" (0,406m)
Depth:4" (0,102m)
Metal thickness: .05" (0,00127 m)
Color:AutumnWhite
Installation holes:Three hangers in a triangular pattern are provided for mounting the
cabinet.The top two are located .29" from the top and spaced 13.75 inches apart.The
lower hanger is located .930" from the bottom and 7.85" from each edge. See Enclosure
Drawing.
Conduit Knockout
½"(0,00127 m) 2" (0,0508 m)
Top Side: 3 1
Bottom Side: 3 1
Right Side: 3 1
Left Side: 3 0
RearSide: 4 0

PRO-2200 Remote Enclosure—PRO22ENC3 9Installation Guide
Power Supply
DO NOT USE POWER SUPPLYTO POWER LOCKS
- 12VDC 2 amp continuous power limited output with backup battery charging and
battery supervision.
- A 16.5VAC 20 VA wall transformer is provided.
- Requires 115VAC/60 hz.
- Maximum battery charge current .5 amp.
- AC on LED.
- AC Fail supervision.
- Low Battery Supervision (form “C” contacts).
- Short circuit and thermal overload protection.
Note: All power connection should be madewith 18 gauge or larger wiring.
LED Diagnostics
ACLED DC LED
ON ON Normaloperating conditions
OFF ON Loss of AC, standby battery supplying power
ON OFF NoDC output
OFF OFF Loss of AC, Discharged or no Standby battery.No DC output.
Backup Power Supply
• Automatic Switch over to standby battery when AC fails (zero voltage drop).
• 4.0amp hour sealed rechargeablebattery (BAT-3).
• Backup time: 1 hr.at maximum 2 amp current draw (longer for configurations with lower
current draw).
Cables Supplied
• Power On Light assembly.
• Tamper Switch assembly - Use ofTamper Switch is required by UL294.
Maintenance
• Replace the 12V 4 amp hour battery every 2 to 2.5 years.
• Oil the hinges on the door every 12 months.
Operating Parameters
• Temperature: 35° F to 110° F (2° C to 43° C).
• Operating Humidity: Up to 85% non-condensing.

10 PRO-2200 Remote Enclosure—PRO22ENC3Installation Guide
BACK
.930
.4975
9.300
13.385
7.850
.975
14.725
.760 14.940
4.120
BOTTOM
.990 1.70
2.000
7.400
10.600
13.500
15.700
13.985
16.015
FRONT
LEFT SIDE
4.660
6.840
9.020
11.875
RIGHT SIDE
1.700
.990
4.660
6.840
9.020
11.875
13.675
TOP
2.200 5.100 8.300 13.700
.990
1.700
PRO-2200 Remote Enclosure

PRO-2200 Remote Enclosure—PRO22ENC3 11Installation Guide
Installation Instructions
1. Remove the 16.5 V 20VA wall transformer from the enclosure.
2. Measure and install the top two mounting screws with heads smaller than .4" (0,1016
m) using proper mounting techniques for the material being used to hold the
PRO22ENC3.Space the screws 13.75" (0,349 m) apart.Leave the screws exposed
approximately 1/2" (1.27 mm).
3. Open the door of the enclosure and place the hanging slots over the mounting screws.
Push the enclosure over the mounting screws and allow the screws to slide into the
slots. Finish tightening the mounting screws to securely hold the enclosure. Screw in
the lower hanger to secure the enclosure against the wall.
4. Run all appropriate wiring to the case through metal conduit. Mark each wire as to
the panel, location and input type. All cable shields should tie to the copper grounding
stud found on the bottom left of the enclosure.
5. Install the required panels onto the proper standoffs using the supplied screws.When
using two full size panels make sure the unused standoffs have nylon screws in
them to prevent short circuits on the panels.This enclosure can mount two full
sizePRO-2200 panels OR one full size panel, one PRO22R1 single reader panel and
onePRO22MX8 multiplexer panel.
6. Wire the readers, input and output connections (see wiring guide at end of booklet).
7. Check all connections prior to powering up the enclosure and panels.
8. Wirethe power supply through the wall transformer provided. Connect to the AC
terminals.Check the voltage at DC+ and DC-.The voltage should be approximately
13.8VDC.
9. Disconnectthe power.
10. Connect the DC power to the panels in parallel. Insure that the connection has the
correct polarity.Follow the wiring diagram supplied with the panels.
11. Wire the AC FAIL and LOW BATT normally closed to appropriate inputs on the panels.
Seeindividual panel wiring diagrams supplied with the panels.
12. Connect the green and yellowTamper Switch wires to the appropriate inputs on the
panels.See individual panel wiring diagrams supplied with thepanels.
13. Connect Communicationswiring per the wiring diagram supplied with the panels.
14. Attach the red battery charging connection to the positive terminal of the battery.The
negative connection is connected at the factory.
15. Check all connections prior to powering up the enclosure and panels.
Installation Diagram 1
W/KEY INSTALLED
SHOWN IN
LOCKED POSITION
SIDE VIEW
15
LOCK
BRACKET
1-REQ'D
12

12 PRO-2200 Remote Enclosure—PRO22ENC3Installation Guide
Installation Diagram 2
Left Open View Right Open View
Part Description
1 Screw 6–32 x 1/4" 12
2 12 VDC Power Supply 1
3 Power Indicator Light Assembly 1
4 Retaining Ring 1
5 Kurly Lok 1
6 16.4 VAC 20 VA Wall Transformer 1
7 Nylon Screws 6–32 x 3/16"
8 KEPS Nuts 6–32 3
9 Tamper Switch 1
10 Tamper Switch Wire Assembly 1
11 Nuts 8–32 2
12 12 V Battery Bracket 1
13 12 V 4.0 amp hour Sealed Battery 1
14 Nut 1/4"–20 Hex with Nylon Insert 2
15 Lock with Key 1
TAMPER SWITCH
1-REQ'D
NUT 6-32 KEPS
3-REQ'D
YEL
GRN
FIRE SAFETY NOTICES ...
Notices
FCC-CDOC and
Fire Safety...
PLACE
STICKER
1/8" FROM
EACH EDGE
BRACKET
1-REQ'D
LOCK W/SF1400
1-REQ'D
BATTERY
1-REQ'D 12
13
8
9
10
15
ADD 2 TO STUD TAMPER SWITCH
WIRE SET
POWER IND LIGHT
WIRE ASSEMBLY
1-REQ'D
RETAINING
RING
1-REQ'D
3
4
14
AC AC
AC FAIL
NO
NC
NO
NC
LOW BAT
+BAT- +DC-
PLACE NYLON
SCREWS INTO
THESE 8 STANDOFFS
SN/1234 date
code
PRO22ENC3 WALL
TRANSFORMER
1 REQ'D (X-5)
6
7
2
1
CONNECT POSITIVE
TAB ON BATTERY
4 REQ'D 5
KURLY
LOK
11
PRO22E3PS
BAT-3
**IMPORTANT**
SUPPRESSORS MUST BE USED
WITH STRIKES, NORTHERN S-4
**IMPORTANT**
ENCLOSURE MUST BE
EARTH GROUNDED

PRO-2200 Remote Enclosure—PRO22ENC3 13Installation Guide
Cable Specifications
Application NCI Part No. AWG Description Max. Dist. Imp. Cap.
N-485connections NC2442-TN N/A Belden9842 4000'(1200m) 120Ω 12.8pf/ft
N/A or equivalent
CR-1, TR-1, CI-1, KR-1 NC1861-BL 18 6 conductor shielded 500' (152 m)
Wiegand card readers
NR-1 magstripe reader NC1861-BL 18 6 conductor shielded 500' (152 m)
PR-1-280 Cotag reader:
280 read head to SZC NC1861-BL 18 6 conductor shielded 300' (91 m)
SZC to N-1000-II NC1861-BL 18 6 conductor shielded 500' (152 m)
PR-2 Hughes reader:
scanner to reader NC1861-BL 18 6 conductor shielded 30' (9 m)
reader to N-1000-II NC1861-BL 18 6 conductor shielded 500' (152 m)
PR-3, PR-5 Indala readers:
A-3/A-5 read head to RE-2 NC18121-YL 18 12 conductor shielded 75' (23 m)
RE-2 to N-1000-II NC1861-BL 18 6 conductor shielded 500' (152 m)
PR-20 , PR-22 Indala readers:
A-20/A-22 read head
to RE-2 NC18121-YL 18 12 conductor shielded 75' (23 m)
RE-2 to N-1000-II NC1861-BL 18 6 conductor shielded 500' (152 m)
PR-10, PR-12 Indala readers: NC1861-BL 18 6 conductor shielded 500' (152 m)
HG-3 hand geometry reader: NC1861-BL 18 6 conductor shielded 500' (152 m)
5 conductor keypad NC1861-BL 18 6 conductor shielded 500' (152 m)
Alarm input points NC 2221-BR 22 2000' (610 m)
Relay outputs NC 1821-OR 18 twisted pair, shielded 2000' (610 m)
NOTE: FOR PLENUM RATED CABLE JUST ADD A “P”TO ENGINEERING SYSTEMS’PART
NUMBERPREFIX;FOR EXAMPLENC1861-BLBECOMES PNC1861-BL

14 PRO-2200 Remote Enclosure—PRO22ENC3Installation Guide
NCI Cable Part Numbers
Part Number Description Application Length
NC1841-GY 18 AWG/4 conductor readercable 1,000'
NC1861-BL-500 18AWG/6conductor readercable 500'
NC1861-BL 18AWG/6conductor readercable 1,000'
NC18121-YL-500 18AWG/12conductor keypadcable 500'
NC18121-YL 18AWG/12conductor keypadcable 1,000'
NCNET-1 50ohm networkcable 1,000'
NC2221-BR 22AWG/2conductor alarmcable 1,000'
NC1821-OR 18AWG/2conductor power/doorcable 1,000'
NCC59206-BK RG-59 videocable 1,000'
NCP1841-GY 18 AWG/4conductorPlenum readercable 1,000'
NCP1861-BL-500 18AWG/6conductorPlenum readercable 500'
NCP1861-BL 18AWG/6conductorPlenum readercable 1,000'
NCP18121-YL 18AWG/12conductorPlenum keypadcable 1,000'
NCP18121-YL-500 18AWG/12conductorPlenum keypadcable 500'
NCPNET-1 50ohmPlenum networkcable 1,000'
NCP2221-BR 22AWG/2conductorPlenum alarmpointcable 1,000'
NCP1821-OR 8 AWG/2 conductorPlenum power/doorcable 1,000'
NC2442-TN 24AWG/120Ω12.8pfRS-485wire communication cable 1,000'
NC2442-TN 24AWG/120Ω12.8pfPlenum communicationcable 1,000'

PRO-2200 Remote Enclosure—PRO22ENC3 15Installation Guide

Honeywell Security & Data Collection
2700 Blankenbaker Pkwy, Suite 150
Louisville, KY 40299
[phone]
www.honeywellaccess.com