Honeywell Lyric Instruction manual

Controller
Quick User Guide
Ref: LCP500-L

– 2 –
These instructions provide a brief overview of common system
functions. For more detailed information, please refer to the
Controller’s full User Guide, located online at:
http://www.honeywell.com/security/hsc/resources/literature/
IMPORTANT!
If the Lyric Controller is beeping rapidly when you enter the
premises, an alarm has occurred during your absence and an
intruder may still be on the premises.
LEAVE IMMEDIATELY and CONTACT THE POLICE from a
nearby safe location.
IMPORTANT!
PROPER INTRUSION PROTECTION
For proper intrusion coverage, sensors should be located at every
possible point of entry to a home or commercial premises. This
would include any skylights that may be present, and the upper
windows in a multi-level building.
In addition, we recommend that radio backup be used in a security
system so that alarm signals can still be sent to the Central
Monitoring Station in the event that the Wi-Fi network connections
or Internet connections are out of order (alarm signals from this
control panel are normally sent over the Wi-Fi and Internet network).
EARLY WARNING FIRE DETECTION
Early warning fire detection is important in a home. Smoke and heat
detectors have played a key role in reducing fire deaths in the United
States. With regard to the number and placement of smoke/heat
detectors, we subscribe to the recommendations contained in the
National Fire Protection Association's National Fire Alarm Code
(NFPA 72). These recommendations can be found in the separate
Part 2 of this document package.
IMPORTANT SECURITY NOTICE
Your key fob is similar to your keys or access card. If lost or stolen,
another person can compromise your security system. Immediately
notify your Dealer/Installer of a lost or stolen key fob. The
Dealer/Installer will then remove the key fob programming from the
security system.

– 3 –
ARM THE SYSTEM
1
Press
Security
icon on
Home
screen.
2
Select arming mode.
Arm Away
(when you’re out)
OR
Arm Stay
(when you’ll be home)
OR
Arm Custom
(bypass selected zones)
3
Enter user code.
4
What Happens
•System arms in selected mode
•Exit Delay countdown begins
•Keypad beeps begin, if enabled
(
Silent Exit
mutes countdown beeps)

– 4 –
DISARM THE SYSTEM
1
Press
Security
Armed
icon.
2
Press
Disarm
icon.
3
Enter user code.
4
What Happens
•System Disarms
•Entry Delay beeps stop (if beeps enabled)
5
Memory of
Alarm
If an alarm has occurred, zones with alarms
remain displayed.
Repeat Disarm sequence to clear display.

– 5 –
BYPASS ZONES
NOTE: Bypassed zones are unprotected.
1
Press
Security
icon.
2
Press
Zones
icon.
3
Select zones to bypass from list.
4
Bypass.
Press
Bypass
.
5
Enter user code.
6
Bypassed zones appear in list with icon.
7
(Away)
(Stay)
(Custom)
Arm system as usual.

– 6 –
PANIC ALARMS
See your installer for the types of Panic alarms programmed for
your system.
1
Press and hold
Panic
button for 3 seconds.
2
Fire
OR
Police
OR
Local
Alarm
OR
Medical
Press desired Panic icon within 5 seconds.
3
Alarm message is sent to your central station.

– 7 –
ASSIGN USER CODES
1
Press
Tools
icon on Security screen.
2
Enter Master User code.
3
Press
Users
icon.
4
Master
Guest
Duress
Add New
To assign a Master, Guest, or Duress code, press
the desired option then press
Edit
.
To assign a regular user code, press
Add New
.
5
Name
User 3
03
User Code
Z-wave Lock
Control
No
If desired, press
Name
to assign a personal name
to this user. Follow the prompts.
If desired, press
Z-Wave Lock Control
to set
whether entering this code at the Z-Wave door
lock will disarm the system. Follow the prompts.
Press
User Code
to assign a 4-digit code to this
user. Go to step 6.
6
Assign 4-digit code and press
Save.

– 8 –
USE AUTOMATION DEVICES (Z-WAVE)
1
Press
Automation
icon.
2
Select type of device.
3
Select a specific device from the list.
4
Select Desired
Action
Select the desired action for that device.
Actions vary based on the device selected.
NOTE
: In some cases, a Z-Wave device might not
report its status to the Lyric controller when an
action is initiated at the device itself (ex.
thermostat or water shutoff valve). This varies
with the manufacturer.

– 9 –
ADD/REMOVE Z-WAVE DEVICES
(Include/Exclude)
1
Press
Automation
icon.
2
Scroll down on device list, press
Tools.
3
Press
Include
to add device.
OR
Press
Exclude
to remove device.
4
Follow the prompts and activate the device’s Function button.
NOTE
: These steps can vary with each Z-Wave device.
Read the device’s instructions and see
Working with Z-Wave
Devices
in the User Guide.

– 10 –
CONTROL SMART SCENES
Smart Scenes are created by using Total Connect. However, Smart
Scenes can be manually started (Run) or placed on Hold using the
Lyric Controller Smart Scenes menu.
1
Press the
Smart Scenes
icon.
2
Enter Master User code.
3
All
Triggered
Anytime
Scheduled
Press
All
to list all the Smart Scenes programmed
in the system.
4
Select a Scene
Select the desired Smart Scene from the list.
5
Run
OR
Hold
OR
Show
To run the selected scene, press
Run
.
To suspend the selected scene, press
Hold
.
To remove the hold later, repeat these steps and
press
Hold
again.
To view the Smart Scene settings, press
Show
.

– 11 –
VIEW CAMERAS
(if installed)
1
Press
VIDEO
icon.
2
System may scan for cameras.
3
Select up to 4 cameras.
4
Press
Display
to view video from selected
cameras.
5
Use zoom in, zoom out, and pan & tilt controls.
6
Press
Scan
to list newly-installed cameras.

– 12 –
SETTINGS
1
Press
Settings
icon.
2
Adjust screen brightness and Voice/Chime
volume.
3
Press
VOICE
or
CHIME
to mute voice
announcements and/or chime sounds if desired
(highlighted [blue] button indicates muted).
4
Press
Clean
icon before cleaning the screen; use
a damp, soft cloth while screen is disabled for 15
seconds.

– 13 –
TEST THE SYSTEM
(to be conducted weekly)
Disarm the system and close all protected windows and doors.
The Home button should show green.
NOTE: No alarm messages are sent to your alarm monitoring
company during these tests.
1
Press
Security
icon on Home screen.
2
Press
Tools
icon on Security screen.
3
Enter the Master user code.
4
Press
Advanced
icon, then select
Walk Test
.
5
Trigger Zones
Trigger (open and close) all zones.
Listen for three beeps from the controller when
each zone is triggered.
6
Exit Test mode
When testing is completed, press the Home
button on the controller and enter the Master
User Code if prompted.

– 14 –
SYSTEM COMPATIBILITY NOTICE
Your Honeywell security system is designed for use with devices
manufactured or approved by Honeywell for use with your security
system. Your Honeywell security system is not designed for use with
any device that may be attached to your security system's keypad or
other communicating bus if Honeywell has not approved such device
for use with your security system. Use of any such unauthorized
device may cause damage or compromise the performance of your
security system and affect the validity of your Honeywell limited
warranty. When you purchase devices that have been manufactured
or approved by Honeywell, you acquire the assurance that these
devices have been thoroughly tested to ensure optimum
performance when used with your Honeywell security system.
Lyric™ Lock
Your system supports advanced features designed to keep it
functioning optimally. These capabilities include: the ability to
interact with Honeywell and your dealer’s network for the setup and
programming of its features, support for remote software updates
and the ability (when enabled by your monitoring dealer) to enhance
your security by preventing an unauthorized takeover of the system
by another monitoring company. In the event that your dealer has
enabled the feature to prevent an unauthorized takeover and you
wish to authorize a new company to take over your system, you may
request that Honeywell remotely disable this feature. Honeywell will
require documentation that you have attempted to contact your
existing security dealer and that they have failed to respond, or
failed to agree to your request.
IN THE EVENT OF PROBLEMS
The user may not under any circumstances attempt any service or
repairs to the security system. Repairs must be made only by
authorized service (see the LIMITED WARRANTY statement for
information on how to obtain service).

– 15 –
SERVICING INFORMATION
Your local authorized service representative is the person best
qualified to service your Lyric system. Arranging some kind of
regular service program with him is advisable.
Your local service representative is:
Name:
Address:
Phone:

Ê800-18080V10Š
800-18080V1 11/15 Rev. A PART 1
2 Corporate Center Drive, Suite 100
P.O. Box 9040, Melville, NY 11747
Copyright © 2015 Honeywell International Inc.
www.honeywell.com/security