Honeywell AutoRAE 2 User manual

AutoRAE 2 System
Quick Start Guide
www.sps.honeywell.com
by Honeywell
Setup
Before using the AutoRAE 2 Controller and AutoRAE 2 Cradle(s) to bump test or calibrate ToxiRAE Pro-family,
QRAE 3, MicroRAE, Handheld PID, and/or MultiRAE-family (pumped versions) instruments, follow the
instructions in the AutoRAE 2 User’s Guide for programming the gas configurations. The steps to follow for
assembly and gas configuration, as well as functionality, are the same for all cradles.
Connections
Assemble the system. Connect the AutoRAE 2 Controller to any Cradles, and then connect the Terminator. For
ToxiRAE Pro Cradles, insert the appropriate adapter.
Important! Make sure an SD card is installed in the AutoRAE 2 Controller. The system cannot operate if an SD
card is not installed. For installation instructions, consult the AutoRAE 2 User’s Guide. Make sure the AutoRAE 2
Controller’s RTC (real-time clock) has been set in Safety Suite Device Configurator (SSDC) before its first use.
Calibration gas cylinders
(each must have a demand-
flow regulator)
Attach Controller to Cradle(s) and then
attach Terminal Adapter to last Cradle.
Insert and tighten
screws, and then put
caps over screws.
Press filter onto
receptacle at
end of Cradle
Plug the barrel from AC adapter into
jack. Then plug its cord into the
transformer, and the transformer
into AC power source.
Exhaust
AutoRAE 2
Controller
AutoRAE 2
Cradles
(maximum
of 10)
Press filter onto
receptacle at end
of Controller
The ToxiRAE Pro Cradle requires
an adapter to be inserted in the
capture mechanism. ToxiRAE Pro
EC (L) and ToxiRAE Pro LEL (L)
and ToxiRAE Pro PID (R).
UltraRAE 3000 or ppbRAE 3000 only:
Use an Active Carbon
Filter for VOC filtering
!

www.sps.honeywell.com
by Honeywell
AutoRAE 2 System
Quick Start Guide
Turning The System On
Toggle the switch on the side of the AutoRAE 2 Controller. The display and power LED glow, and the LEDs on attached
cradles light up. The AutoRAE 2’s internal pump and the valves in the system are tested. If self-checkout is successful, the
system is ready to use. The display provides a list of the AutoRAE 2 Cradles, and if there are instruments in them, the
names of the instruments are included in this list.
Make sure calibration gases match the configurations created in Safety Suite Device Configurator (SSDC) and
transferred to the AutoRAE 2 Controller. Also make sure the gas cylinders have sufficient gas in them and that they
are attached properly.
Place An Instrument In The Cradle
Make sure the filter on the instrument is not dirty or clogged (MiniRAE 3000, ppbRAE 3000, UltraRAE 3000, and
MiniRAE Lite must be equipped with Quick Connectors and have their inlet probes removed).
Important! For MicroRAE, make sure the external filter is removed from the unit before placing it in the Cradle.
1. Make sure the instrument is in AutoRAE 2 Mode or turned off.
2. Place the instrument into the cradle face-down, making sure that it is aligned correctly with the contacts on the
AutoRAE 2 Cradle’s charging port. There are two alignment points on one side and one alignment point on the
other side, designed to mate with matching points on the bottom of the instrument.
3. Press in on the capture mechanism to lock the instrument in place.
Automatic Warm-Up Before Bump Testing Or Calibrating
When you place an instrument in the cradle and lock the capture mechanism, the instrument begins charging and is
automatically warmed up. Warm-up time depends on the sensors installed in the instrument and their individual
warm-up requirements.
Display Color Coding
The AutoRAE 2 Controller has a color display, so colors are used to indicate status in different categories of
information.
Status
Color
Explanation
Pass
Green
1. All sensors and alarms passed bump test.
2. All sensors and alarms passed calibration.
Pass?
Green
1. All sensors that were tested passed bump test. Some sensors were not tested.
2. All sensors that were calibrated passed calibration. Some sensors were not calibrated.
Fail
Red
1. One or more sensors or alarms failed bump test.
2. One or more sensors or alarms failed calibration.
3. Monitor not detected after 30 minutes.
4. Monitor warm-up or other error.
Warning
Yellow
Sensor does not match the gas.
Warm-up
None
Instrument warm-up.
Ready
None
Instrument ready to bump test or calibrate.
MultiRAE
ToxiRAE Pro
QRAE 3
Handheld PID
MicroRAE

www.sps.honeywell.com
AutoRAE 2 System
Quick Start Guide
by Honeywell
Bump Testing
You can bump test all or individually selected instruments that are seated in the system’s cradles.
From the main screen, enter Bump Test by pressing [Y/+] twice (“Function” and then “Select”).
Note: Any cradle that does not have an instrument in it is shown with a gray checkbox. You cannot check/uncheck
this box.
To select all instruments in cradles to bump test:
1. Press [Y/+]. When you check “Bump All,” the “Bump All” checkbox and all of the other checkboxes for
cradled instruments are automatically checked.
2. Press [MODE] for “Done.”
3. Press [Y/+] to start.
To select specific instruments to bump test:
1. Press [N/-] to scroll down the list to an instrument you want to select for bump testing.
2. Press [Y/+] to toggle the selection between unchecked and checked.
3. Press [MODE] for “Done.”
4. Press [N/-] to select “Exit,” and then press [Y/+] to exit.
If you did not press [Y/+] to start the process, then a countdown begins. When the countdown reaches zero, then
the instruments are bump tested.
To abort a bump test: Press [N/-]. You will be asked if you want to abort the process. Press [Y/+] for “Yes” and
[N/-] for “No.”
IMPORTANT!
If an instrument does not pass a bump test, a full calibration is automatically started.

www.sps.honeywell.com
AutoRAE 2 System
Quick Start Guide
by Honeywell
Calibration
You can calibrate all or individually selected instruments that are seated in the system’s cradles.
From the main screen, enter Calibrate by pressing [Y/+] (“Function”), and then [N/-] until “Calibrate” is highlighted.
Then press [Y/+] to select it.
Note: Any cradle that does not have an instrument in it is shown with a gray checkbox. You cannot check/uncheck
this box.
To select all instruments to calibrate:
1. Press [Y/+]. When you check “Calibrate All,” the “Calibrate All” checkbox and all of the other checkboxes
for cradled instruments are checked.
2. Press [MODE] for “Done.”
3. Press [Y/+] to start.
To select specific instruments to calibrate:
1. Press [N/-] to scroll down the list to an instrument you want to select for calibration.
2. Press [Y/+] to toggle the selection between unchecked and checked.
3. Press [MODE] for “Done.”
4. Press [N/-] to select “Exit,” and then press [Y/+] to exit.
If you did not press [Y/+] to start the process, then a countdown begins. When the countdown reaches zero, then the
instruments are calibrated.
To abort calibration: Press [N/-]. You will be asked if you want to abort the process. Press [Y/+] for “Yes” and
[N/-] for “No.”

www.sps.honeywell.com
AutoRAE 2 System
Quick Start Guide
by Honeywell
Removing An Instrument From A Cradle
To remove an instrument from a cradle, press the button to release the capture mechanism. Then lift the instrument
from its inlet end.
Charging An Instrument’s Battery
Each AutoRAE 2 Cradle attached to an AutoRAE 2 Controller automatically charges an instrument’s battery when
it is docked. The Charge Status LED glows red to indicate that charging is taking place. When the instrument’s
battery is fully charged, the LED glows green.
Active Carbon Filter For Removing VOC
Whether zeroing a ppbRAE 3000, an UltrRAE 3000, or in an environment in which the ambient air has VOC
(volatile organic compounds), it is strongly recommended to use an Active Carbon Filter (P/N: 490-0006-000),
which filters out VOC from the air.
When an AutoRAE Controller is used with one or more Cradles, the air inlet on each attached cradle is disabled and
air is taken in through the Controller’s air inlet. Therefore, you only need to use one Active Carbon Filter for the
Controller instead of on each cradle. To install the Active Carbon Filter on the Controller:
1. Remove the standard filter (if one is installed).
2. Remove the plastic filter adapter by twisting the plastic filter clockwise while gently pulling outward.
3. Press the Active Carbon Filter into the receptacle. The filter is designed for 20 uses. To help you keep track
of how many calibrations are performed, there are 20 small boxes painted on the surface of the filter that you
can mark with a pen after each use. Note: Make sure the arrow on the side of the filter points toward the
Controller.
MultiRAE
ToxiRAE Pro
QRAE 3
Handheld PID
Press Active Carbon
Filter into receptacle
Remove standard filter
Remove plastic
filter adapter
MicroRAE

www.sps.honeywell.com
AutoRAE 2 System
Quick Start Guide
by Honeywell
Handheld PID Monitors Must Be Equipped With A Quick Connector
You must remove the inlet probe before placing a handheld PID instrument (MiniRAE Lite, MiniRAE 3000, ppbRAE
3000, or UltraRAE 3000) into the cradle. If the instrument does not have a Quick Connector (P/N: T02-3301-000) already
installed, you must install one.
Installing A Quick Connector
UltraRAE 3000: MiniRAE Lite, MiniRAE 3000, or ppbRAE 3000:
Rev F EN
© June 1, 2021
P/N T02-4002-000
CORPORATE HEADQUARTERS
RAE Systems
by Honeywell
300 S
Tryon St. Suite 500
Charlotte,
NC 28202, USA
Phone:
[phone]
Fax:
[phone]
rae
[e-mail]
WORLDWIDE SALES OFFICES
USA/Canada:
1.877.723.2878
Europe: +45.86.52.51.55
Middle East: +00971.4.440.5949
China: +86.10.5885.8788
-3000
Asia Pacific: +852.2669.0828
Do not use a RAE-Sep Tube in the
UltraRAE 3000 tube holder when
using it with an AutoRAE 2 Cradle.
!