Honeywell PRO22IC User manual

PRO-2200
Intelligent Controller
Installation Manual
Part Number: PRO22IC
TD1146 rev0501

PRO-2200 Intelligent Controller PRO22IC 3Installation Guide
Contents
Warnings and Cautions ........................................................................................ 4
Disclaimer........................................................................................................... 6
Unpacking Procedure ........................................................................................... 6
Shipping Instructions ............................................................................................ 7
Limited Warranty ................................................................................................. 7
Confidentiality ..................................................................................................... 8
Description .......................................................................................................... 9
Set Up ................................................................................................................ 9
LED Operation .................................................................................................. 10
Power................................................................................................................ 10
Communications ............................................................................................... 11
Alarm Inputs...................................................................................................... 12
Memory Backup Battery...................................................................................... 12
Mounting Options ............................................................................................. 12
Suggested Installation Sequence ......................................................................... 12
Specification Summary ....................................................................................... 13
Wiring Diagram ................................................................................................ 14

4 PRO-2200 Intelligent Controller PRO22ICInstallation Guide
Warnings and Cautions
WARNING
Before installation, TURN OFFthe external circuit breaker which supplies power to the
system.
Before connecting the device to the power supply, verify that the output voltage is within
specifications of the power supply.
Do not apply power to the system until after the installation has been completed.
Personal injury ordeathcouldoccur,andtheequipmentcould be damaged beyondrepair,
iftheseWARNINGSarenotobserved!
WARNING
Fire Safety and Liability Notice
Never connect card readers to any critical entry, exit door, barrier, elevator or gate without
providing an alternative exit in accordance with all fire and life safety codes pertinent to
the installation.These fire and safety codes vary from city to city and you must get
approval from local fire officials whenever using an electronic product to control a door or
other barrier.Use of egress buttons, for example, may be illegal in some cities.In most
applications, single action exit without prior knowledge of what to do is a life safety
requirement.Always make certain that any required approvals are obtained in writing.DO
NOT ACCEPTVERBAL APPROVALS,THEY ARE NOTVALID.
EngineeredSystemsneverrecommendsusing the PRO-2200 or relatedproductsforuse
as a primary warning or monitoring system. Primary warningormonitoring systemsshould
always meet local fire and safety code requirements.The installer must also test the
system on a regular basis by instructing the end user in appropriate daily testing proce-
dures.Failure to test a system regularly could make installer liable for damages to the end
user if a problem occurs.
WARNING
EARTH groundallenclosures,for proper installation.
WARNING
Use suppressors on all door strikes. Use S-4 suppressors for installation. Engineered
Systems Group recommends only DC strikes.
©2001EngineeringSystems
The information in this document is subject to change without notice.

PRO-2200 Intelligent Controller PRO22IC 5Installation Guide
CAUTION
IF ANY DAMAGETOTHE SHIPMENT IS NOTICED, A CLAIM MUST BE FILEDWITH
THE COMMERCIAL CARRIER RESPONSIBLE.
CAUTION
Electro-static discharge can damage CMOS integrated circuits and modules.
To prevent damage always follow these procedures:
Use static shield packaging and containers to transport all electronic components,
including completed reader assemblies.
Handle all ESD sensitive components at an approved static controlled workstation.These
workstations consist of a desk mat, floor mat and an ESD wrist strap.Workstations are
available from various vendors.
NOTICE
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules.These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment.This equipment generates, uses, and can radiate radio fre-
quency energy and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications.Operation of this equipment in
a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
NOTICE
This document and the data in it shall not be duplicated, used or disclosed to others for
procurement or manufacture, except as authorized by and with the written permission of,
Engineering Systems.The information contained in this document or in the product itself
is considered the exclusive property and trade secrets of Engineering Systems.Copyright
laws of the United States protect all information in this document or in the software
product itself.
NOTICE
Any use of this product is subject to the terms and acceptance of the Engineering
Systems Software Agreement. Please request a copy from Engineering Systems, and
review theagreement carefully.

6 PRO-2200 Intelligent Controller PRO22ICInstallation Guide
Disclaimer
Product Liability; Mutual Indemnification
In the event that a Customer receives a claim that a Product or any component thereof
has caused personal injury or damage to property of others, Customer shall immediately
notify Engineering Systems in writing of all such claims. Engineering Systems shall
defend or settle such claims and shall indemnify and hold Customer harmless for any
costsordamagesincludingreasonable attorneys’ fees whichCustomermayberequired
to pay as a result of the defective Product or the negligence of Engineering Systems, its
agents, or its employees.
Customer shall hold harmless and indemnify Engineering Systems from and against all
claims, demands, losses and liability arising out of damage to property or injury to
persons occasioned by or in connection with the acts or omissions of Customer and its
agents and employees, and from and against all claims, demands, losses and liability for
costs of fees, including reasonable attorneys’ fees, in connection therewith.
Unpacking Procedure
CAUTION
If any damage to the shipment is noticed before unpacking, a claim must be filed with the
commercial carrier.
All containers should be opened and unpacked carefully in order to prevent damage to
the contents.
The following steps are used to unpack equipment in preparation for installation:
1.Open the container and remove the unit(s) and all packing material.Retain the
container and all packing materials. They may be used again for reshipment
of the equipment, if needed.
2. Inspect the contents for shortage.If items are missing items, contact the order entry
department at800-323-4576.
3.Visually check contents. If damage is discovered, perform the following:
If shipping caused damage to the unit, a claim must be filed with the
commercialcarrier.
If any other defect is apparent, call 800-323-4576 for a return authorization.

PRO-2200 Intelligent Controller PRO22IC 7Installation Guide
Shipping Instructions
To ship equipment back to Engineering Systems:
1.Contact the customerservice department beforereturning equipment at800-323-4576.
Whencallingpleasehave available:
•A description of the problem or reason for returning the equipment.
•Original purchase order number, invoice number and if the unit is under warranty.
•A new purchase order number if the unit is not under warranty.
2. Obtain the Return Authorization Number (RMA) from the customer service
department at800-323-4576.
3.Show the RMA number on all packages shipped.Packages, which are not marked with
an RMA number will be refused at the factory and returned COD.
4.Carefullypacktheequipment for shipment. Use theoriginalpackingmaterialwhenever
possible.
Limited Warranty
All Products sold or licensed by Engineering Systems include a warranty registration card
which must be completed and returned to Engineering Systems by or on behalf of the end
user in order for Engineering Systems to provide warranty service, repair, credit or ex-
change. All warranty work shall be handled through the Customer which shall notify
EngineeringSystemsandapply for a ReturnMerchandiseAuthorization(RMA) number
prior to returning any Product for service, repair, credit or exchange. Engineering Systems
warrants that its Products shall be free from defects in materials and workmanship for a
period of two years from date of shipment of the Product to Customer.The warranty on
Terminals, Printers, Communications Products and Upgrade kits is 90 days from date of
shipment. Satisfaction of this warranty shall be limited to repair or replacement of Prod-
ucts which are defective or defective under normal use. Engineering Systems’warranty
shall not extend to any Product which, upon examination, is determined to be defective as
a result of misuse, improper storage, incorrect installation, operation or maintenance,
alteration, modification, accident or unusual deterioration of the Product due to physical
environments in excess of the limits set forth in Product manuals.THERE ARE NO
WARRANTIESWHICH EXTENDBEYONDTHIS PROVISION.THISWARRANTYIS IN
LIEUOFALLOTHERWARRANTIESWHETHER EXPRESS, IMPLIEDORSTATUTORY,
INCLUDINGIMPLIEDWARRANTIES OF MERCHANTABILITY ORFITNESSFORANY
PARTICULAR PURPOSE.NOREPRESENTATION ORWARRANTYOFTHEDISTRIBU-
TOR SHALL EXTENDTHE LIABILITY OR RESPONSIBILITY OFTHE MANUFACTURER
BEYONDTHETERMS OFTHIS PROVISION.IN NO EVENT SHALL ENGINEERING
SYSTEMS BE LIABLE FOR ANY RE-PROCUREMENT COSTS, LOSS OF PROFITS,
LOSS OF USE, INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGESTO ANY
PERSONRESULTINGFROMTHE USE OF ENGINEERING SYSTEMS’PRODUCTS.

8 PRO-2200 Intelligent Controller PRO22ICInstallation Guide
Confidentiality
All software, drawings, diagrams, specifications, catalogs, literature, manuals and other
materials furnished by Engineering Systems relating to the design, use and service of the
Products shall remain confidential and shall constitute proprietary rights of Engineering
Systems and Customer agrees to treat such information as confidential. Customer shall
acquire no rights in the design of the Products or the related materials except to use such
information solely for the purpose of and only during the time it sells the Products.
Customer shall not copy the design of any of the Products or use or cause to be used any
Product design or related materials for its own benefit or for the benefit of any other party.
The covenants contained in this section shall remain effective throughout the term of this
Agreement and thereafter unless specifically waived by Engineering Systems in writing.

PRO-2200 Intelligent Controller PRO22IC 9Installation Guide
Description
The Intelligent Controller is the heart of the PRO-2200 and provides the real time
processing for the connected I/O interfaces. It holds the database for the subsystem
configuration and card holders, and the event log buffer in battery-backed memory.
Port 1 provides the standard connection to the host computer.
1. Port 1 may be set up as an RS-232 interface or an RS-485 interface. An optional
interface board (PRO22EN) converts the RS-232 output of port 1 into an Ethernet port
capable of supporting TCP/IP. If this interface board is present, this port must be set
up as an RS-232 interface and Jumper J-14 must be removed.
2. Ports 2 & 3 are RS-485 interfaces.
An on-board real time clock maintains the date and time, taking into account leap year
and accounting for global time zones and daylight savings time changes. The program is
stored in FLASH memory and may be downloaded through a serial port, allowing the
programtobechanged without physically changingboardcomponents.
Set Up
The controller hardware is configured with jumpers and a set of eight switches.These
jumpers/switches setup the memory chip size, port interface, end of line termination,
controller address, and baud rate. Please refer to the tables.
JumperSettings:
SREPMUJTATESDETCELES
6,5,4J 3-2 232-SRSI1TROP
2-1584-SRSI1TROP
41J FFO ORCIMXOBOC,TENREHTESI1TROP
NO584-SRRO232-SRSI1TROP
9J FFO NOTONSIROTANIMRETLOE584-SR1TROP
NONOSIROTANIMRETLOE584-SR1TROP
21J FFO NOTONSIROTANIMRETLOE584-SR2TROP
NONOSIROTANIMRETLOE584-SR2TROP
31J FFO NOTONSIROTANIMRETLOE584-SR3TROP
NONOSIROTANIMRETLOE584-SR3TROP

10 PRO-2200 Intelligent Controller PRO22ICInstallation Guide
DIP Switch Settings:
LED Operation
Thecontrollerusesthreeon-board LEDs to provide statusinformationduringitspower-up
sequenceandnormal operation.
EDOM
DELADELBDELCNOITPIRCSED
pu-rewoP ecneuqeS
NOFFOFFOputeserawdrah,pu-rewoPtratS
FFONONOesabataDgniraelCdnaMARgnitseT )BM/.ces5.xorppa(
FFONOFFO esabataDgniraelCTONdnaMARgnitseT .K.Osiesabatad)BM/.ces5.xorppa(
NONONOdnoces1rofdleh,etelpmocpu-rewoP
lamroN noitarepO
HSALF ecnohsalfdluohsdnarekcilftniafasahDELsihT .evitcasimetsysnehwdnocesyreve
HSALF noytivitcasierehtnehwhsalF 1troPtsoH
HSALF .troPO/InoytivitcasierehtnehwhsalF )3&2stroP(
8S7S6S5S4S3S2S1SNOITCELES
FFOFFOFFONO1SSERDDA
FFOFFONOFFO2SSERDDA
FFOFFONONO3SSERDDA
FFONOFFOFFO4SSERDDA
FFONOFFONO5SSERDDA
FFONONOFFO6SSERDDA
FFONONONO7SSERDDA
FFOFFOFFOFFO8SSERDDA
FFO WOLFERAWDRAHON:1TROP
LORTNOC
NO WOLFERAWDRAH:1TROP
LORTNOC
FFOFFO SPBK2.511
FFONO SPB006,9
NOFFO SPB002,91
NONO SPB004,83
FFO DROWSSAPON
NO DERIUQERNOGOLDROWSSAP