Honeywell TrueZONE HZ311 User manual

Zoning System Design Manual
Zoning Made Effortless
70-2321-03

Zoning System Design Manual
70-2321—03 2
IntroductIon
The Concept of Zoning
The basic principle of forced air zoning is to allow one HVAC system to be controlled by multiple thermostats,
heating and cooling a building in zones rather than as a whole. This makes homes and businesses more comfort-
able. When combined with setback thermostats, zone setback is possible, resulting in significant energy savings.
Forced air zoning makes a common HVAC system more efficient by concentrating the unit’s capacity where and
when you need it instead of pouring air throughout the building regardless of the temperature in the individual
rooms.
According to a 2006 American Home Comfort Study, 67% of US homeowners are uncomfortable in their homes at
certain times of the year. Zoning solves this problem.
To accomplish this we utilize:
Zoning Panel—Receives requests from thermostats and coordinates the HVAC system and damper positions.
Thermostats—Requests conditioned air only in zones where required.
Duct Dampers—Directs air to rooms (zones) only when called for by a room thermostat.
A By-Pass Damper—Efficiently controls excess supply air as dampers open and close.
Discharge Air Temperature Sensor (DATS)—Avoids freeze-up and tripping on high limit by sensing the sup-
ply duct temperature. The zone panel cycles off the equipment when DATS limits are exceeded. The equipment is
turned back on automatically.
Fig. 1 depicts typical home temperatures compared to those of a home with Honeywell zoning.
M28112
FIRST FLOOR
(LIVING AREA)
ROOM TEMPERATURE
72°F
22°C
THERMOSTAT
SETPOINT:
72°F/22°C
TYPICAL HOME
SECOND FLOOR
(SLEEPING AREA)
ROOM TEMPERATURE
76-80°F
25-27°C
ZONE 2
(LIVING AREA)
ROOM TEMPERATURE
72°F
22°C
THERMOSTAT SETPOINT:
72°F/22°C
THERMOSTAT SETPOINT:
72°F/22°C
IDEAL HOME - WITH HONEYWELL ZONING
ZONE 1
(SLEEPING AREA)
ROOM TEMPERATURE
72°F
22°C
Fig. 1. Typical home (no zoning) compared to ideal home with Honeywell zoning.
Need Help?
For assistance with this product please visit http://yourhome.honeywell.com
or call Honeywell Zoning Hotline toll-free at 1-800-828-8367

Zoning System Design Manual
3 70-2321—03
M28051
FAMILY
ROOM
LIVING
ROOM
ENTRY BEDROOM
1
BEDROOM
2
MASTER
SUITE
DINING
ROOM
KITCHEN
BATH
HVAC EQUIPMENTZONE THERMOSTAT
ROUND ZONE DAMPER
DIFFUSER
BATH
Fig. 2. Typical residential layout with multiple zones on one HVAC system.
Fig. 2 depicts a typical residential layout with three zones. Zoning provides two key benefits:
• Customer Comfort: heating and cooling where you want it, when you want it.
• Energy Savings: heat and cool only zones that are occupied.
In the following pages you will learn how to apply the principles of forced air zoning in new and existing projects,
creating a more comfortable indoor environment.
IntroductIon

Zoning System Design Manual
70-2321—03 4
Plan the Zones
Panel
• To Operate Dampers and
Equipment
• Transformer to power panel
Thermostats
• Programmable or
Non Programmable
Dampers
• Round/Rectangular
Bypass and Discharge Air
Temperature Sensor:
• To Prevent Static Pressure
Buildup
• DATS protects Equipment
In planning a zone system, here's what you need:
1
Divide the Home Into Zones
There are a number of ways to divide a house into zones: by floor, in groups of rooms adjacent to each
other, rooms grouped by compass orientation—here is a typical setup:
Zone 1: areas primarily used at night (bedrooms)
Zone 2: areas primarily used during the day (living room, kitchen)
Zone 3: a third space that would benefit from its own HVAC control, such as a master bedroom suite,
a basement, living space above a garage, a home office, etc.
A good rule of thumb is to make no zone smaller than about 25% of total system capacity, measured in
cubic feet/minute (CFM).
M28111
Fig. 3. Typical residential layout with multiple zones on one HVAC system.
Zone 1: Daytime
Zone 1: Daytime
Zone 2: Night-time
Zone 2: Night-time
Zone 1: Daytime
Zone 1: Daytime
Zone 2: Night-time
Zone 2: Night-time
Zone 3:
Home
office
Zone 3:
Home
office

Zoning System Design Manual
5 70-2321—03
ducts and damPers
2
Size the Ductwork
In New Construction: ductwork is sized as usual for the size of the home; trunks are sized for the
amount of air going to the zone.
Ductwork should be designed normally, typically .10 or .08 in. w.c./100 ft.
Proper duct design of a zoned system will:
• Maintain proper airflow through the HVAC unit when only one zone is open.
• And maintain proper airflow to all zones when all are open.
In Retrofit Applications: zones are somewhat limited by how the ducts were originally constructed,
but any home can be zoned provided there is access to the ductwork. See page 10 for zoning informa-
tion specific to retrofit applications.
3
Select Dampers
Use ZD dampers for rectangular ducts. Use ARD or
RRD dampers for round ducts in residential systems up
to 2000 CFM.
For systems over 2000 CFM or commercial systems,
see page 11.
Install the Dampers
A supply air damper should not be placed closer than 6
ft. to a diffuser. The damper should also be at least 3 ft.
away from the plenum. (Less than 6 ft. between damper
and diffuser could create objectionable air noise in the
conditioned space and 3 ft. of duct off the plenum will
reduce turbulence.) These minimums are recommenda-
tions for optimal performance; however, each installa-
tion presents its own challenges, so each installation will vary. For instance, in some installations the
damper may need to be mounted directly on the plenum.
Allow for Access
Dampers should be installed in a location that can be accessed for service. If a damper needs to be
"buried," place a decorative register over it to provide access.
Balancing Dampers
Balancing dampers should be included in the duct work, because a zoned home needs to be balanced
just as a non-zoned home does.

Zoning System Design Manual
70-2321—03 6
Size the Bypass Damper
Install between supply and return.
All zoning systems should be installed with a supply-to-return bypass damper. A Static Pressure
Regulating Damper (SPRD) is used to bypass excess airflow from the supply duct into the return duct.
4
Supply duct systems should be sized to handle
the total airflow when all zones are open, and use
a SPRD bypass capable of handling the excess air
when only the smallest zone is calling. Excess air
should be bypassed into the return air duct. If the
space is too confined to install a bypass back to the
return, excess air can also be dumped into a hall-
way, false ceiling, or basement.
Determine the size of the bypass as follows:
CFM System
- CFM Smallest Zone
= CFM Bypass
For example, on a 4-ton system .............................. 1600 CFM System
with the smallest zone designed to handle ............ - 400 CFM Smallest Zone
the by-pass must be able to handle........................ = 1200 CFM of airflow in bypass
When few zones are calling, static pressure in the system increases, and air is bypassed from supply to return.
This ensures that the throw of air at the register is correct whether one zone is calling or all zones are calling.
This method of duct design is also a great way to control excess humidity in the home, especially in southern
climates. Bypassing air from the supply duct into the return duct accelerates the dehumidification ability of the
equipment, creating greater comfort for the homeowner.
Table 1. SPRD Dimensions.
Round SPRD Rectangular SPRD
Model Number By-Pass Model Number By-Pass
SPRD7 300 CFM SPRD12X8 1000 CFM
SPRD8 400 CFM SPRD12X10 1200 CFM
SPRD9 600 CFM SPRD12X12 1400 CFM
SPRD10 750 CFM SPRD20X8 1600 CFM
SPRD12 1200 CFM SPRD20X10 2000 CFM
SPRD14 1800 CFM SPRD20X12 3000 CFM
SPRD16 2400 CFM
ByPass damPers and dats

Zoning System Design Manual
7 70-2321—03
ROOF TOP EQUIPMENT
DISCHARGE AIR
TEMPERATURE SENSOR (DATS)
THE DATS MUST BE LOCATED SO THAT
IT CAN PROPERLY SENSE THE LEAVING
AIR TEMPERATURE.
NOTE: MOUNTING THE DATS TOO CLOSE
TO THE HEAT EXCHANGER OR EVAPORATOR
COIL WILL CAUSE EXCESSIVE CYCLING OF
THE SYSTEM AND RESULT IN DISCOMFORT
FOR THE BUILDING OCCUPANTS.
M28055
UP FLOW
HORIZONTAL
Fig. 4. DATS mounting locations.
ByPass damPers and dats
Alternative Bypass Methods
If there is no space for bypass ductwork, the zone dampers can be set to allow some air to leak. By setting the
larger zone dampers to a minimum position, excess air pressure can be relieved even when only one zone is call-
ing. This method does not typically affect room temperature, but the homeowner should be advised that air will be
coming from these registers even when that zone is not calling.
Discharge Air Temperature Sensor (DATS)
The DATS should be located in the supply trunk between the evaporator coil or heat exchanger and the first zone
damper. If this is not possible, it is permissible to mount the DATS in the bypass duct.

Zoning System Design Manual
70-2321—03 8
Install the Panel
Mount on return, stud, wall, or roof truss.
Zone Panels should not be exposed to weather or installed in a location where they might get wet. Like
a damper, they must be accessible for service, if required. Select a conventional zone control panel or
communicating zone panel using Table 2 and 3. Notice that no fossil fuel kit is necessary for the HZ432
in dual fuel applications, but is necessary for all other panels.
5
Zone Panel
APPLICATION
2 TO 3 ZONE
2 TO 32 ZONES
CONVENTIONAL
1-HEAT/1-COOL
HZ322
OR
HZ311
HZ432
CONVENTIONAL
2-HEAT/2-COOL
CONVENTIONAL ZONE PANEL SELECTION GUIDE
HZ322
HZ432
HEAT PUMP
2-HEAT/1-COOL
HZ322
HZ432 HZ432
HEAT PUMP/
CONVENTIONAL
3-HEAT/2-COOL OR
DUAL FUEL 2 HEAT/2-COOL
HZ432
with W8665E
WIRELESS ZONING
WITH
T8665A WIRELESS
THERMOSTAT
HZ322 OR HZ311
with W8665E
HZ432 OR HZ322
with W8665E
HZ432 OR HZ322
with W8665E
M19800B
APPLICATION
NETWORKED ZONING SELECTION GUIDE
M19801A
THERMOSTAT
CONVENTIONAL/
HEAT PUMP
OPERATES SINGLE STAGE,
MULTISTAGE, AND
HEAT PUMP EQUIPMENT
UP TO 3-HEAT/2-COOL
EQUIPMENT INTERFACE
MODULE
TH9421C1004
or
TH5320C1002
DAMPER INTERFACE
MODULE
UP TO 9 ZONES TOTAL
W8635D
C7835A1009
W8835A1004
DISCHARGE AIR
TEMPERATURE SENSOR
DATS
NOT NEEDED
FOR ZONES 1-3
ONE W8703A FOR EVERY
3 ZONES FROM 4-9
TELEPHONE
ACCESS MODULE
Table 2. Conventional Zone Panel Selection Guide.
Table 3. Networked (Communicating) Zoning Selection Guide.

Zoning System Design Manual
9 70-2321—03
RH
RC
W1/E
W2
W3
Y1
Y2
G
O
B
DS/BK
M28169
HVAC
FAN RELAY
24 VOLT TRANS.
G
Y
Y2
BK
CR
W
COMPRESSOR
RELAY
W2
EQUIPMENT
If using a Honeywell TrueZONE panel, the panel's
DS/BK terminal is intended for use with a vari-
able-speed fan. When one zone is calling (or less
than 25% of capacity on systems with more than 4
zones), this terminal will be de-energized of 24 VAC.
This reduces blower speed on most variable speed
blowers.
Transformer
Mount and wire a dedicated transformer to the zone panel. The AT140A1042 is rated to 130°F (54°C). If it is to be
mounted in an attic that may get much hotter, install the AT175A1008, which is rated to provide 50 VA at 165°F (74°C).
Connect power to the zone control panel after all other wires are attached.
Variable Speed Fan
A variable speed fan or ECM blower changes blower speed to deliver a constant CFM regardless of static pressure.
To use zoning with a variable speed fan, plan and install zoning normally, and use an SPRD or a MARD (round)
damper with static pressure control (SPC) for bypass.
The zone panel is typically installed near the indoor unit, in a garage, crawl space, basement, or attic. Zone panels
are often installed on the return air duct. However, in some heat pump applications, the homeowner or building
occupant may require access to the panel to change
into the emergency heat mode. To meet these needs,
install the panel in a utility closet or other convenient
area where the panel is easily accessed.
SUPPLY DUCT
DATS (AT LEAST 3 FT
FROM PLENUM)
DATS
(ALTERNATE LOCATION)
TrueZONE PANEL MOUNTED
ON RETURN DUCT
TrueZONE PANEL
MOUNTED ON WALL
ZD SERIES
ZONE DAMPERS
SPRD BYPASS DAMPER
FURNACE OR AIR CONDITIONER
M24921
Fig. 5. Typical upflow HVAC system.
Fig. 6. Typical horizontal
HVAC system.
Fig. 7. Wiring variable speed
fan to TrueZONE panel.
Zone Panel
DATS
M28164
SUPPLY
DUCT
RETURN
DUCT
BYPASS
DAMPER
ZONE PANEL
(DUCT MOUNT)
ZONE PANEL
(WALL MOUNT)
ARD
DAMPERS
DATS
(ALTERNATE LOCATION)
Thermostats
Install thermostats using instructions
provided with thermostat. Wireless
thermostats can be used to speed
installation.

Zoning System Design Manual
70-2321—03 10
retrofIt aPPlIcatIons
For retrofit applications, first you have to ensure that the duct system is adequate for room/zone loads, and that
the existing HVAC system is properly sized to deliver heat/cool. After that, planning the zone system is very similar
to new construction.
Flex Duct
For retrofit applications in flex duct, use round ARD dampers. The round ARD is a galvanized steel single blade
damper with a low-leakage gasket, and comes in a range of sizes from 5–20 in. You can use multiple ARDs on any
duct—just wire them in parallel.
Thermostats
The existing thermostat can often be used for one zone, but as it might be difficult to run wires to the other zones,
Honeywell wireless thermostats can be used.
Rigid Duct, Rectangular Sheet Metal Duct, Knockdown (KD) Duct
Using a retrofit round damper (RRD) significantly reduces
labor—it installs in a fraction of the time—and overall system
installation cost. A retrofit damper slides into rigid round pipe
for quick installation.
Honeywell offers dampers for rigid round duct in 5-, 6-, 7-, and
8-in. diameters. Multiple RRD dampers may be wired in parallel.
M28119
Fig. 8. Installing retrofit round damper.