Honeywell Touchpoint Plus Release Note

i
Technical Handbook
Touchpoint Plus

MAN0984_Iss 3_02/16 Touchpoint Plus
Pt. No. 3011M5001_3 ii Technical Handbook
Revision History
Revision Comment Date
Issue 01 First Issue and initial translations 30/05/2015
Issue 02 Added new chapters, new data and final translations 09/06/2015
Issue 03 Completely Revised; added Expansion Unit, Dual Input Module and Modbus 29/02/2016

Conditions of Use
MAN0984_Iss 3_02/16 Touchpoint Plus
Pt. No. 3011M5001_3 iii Technical Handbook
Disclaimer
In no event shall Honeywell be liable for any damages or injury of any nature or kind, no matter how caused, that arise
from the use of the equipment referred to in this manual.
Strict compliance with the safety procedures set out and referred to in this manual, and extreme care in the use of the
equipment, are essential to avoid or minimise the chance of personal injury or damage to the equipment.
The information, figures, illustrations, tables, specifications, and schematics contained in this manual are believed to be
correct and accurate as at the date of publication or revision. However, no representation or warranty with respect to such
correctness or accuracy is given or implied and Honeywell will not, under any circumstances, be liable to any person or
corporation for any loss or damages incurred in connection with the use of this manual.
The information, figures, illustrations, tables, specifications, and schematics contained in this manual are subject to
change without notice.
Unauthorised modifications to the gas detection system or its installation are not permitted, as these may give rise to
unacceptable health and safety hazards.
Any software forming part of this equipment should be used only for the purposes for which Honeywell supplied it. The
user shall undertake no changes, modifications, conversions, translations into another computer language, or copies
(except for a necessary backup copy).
In no event shall Honeywell be liable for any equipment malfunction or damages whatsoever, including (without limitation)
incidental, direct, indirect, special, and consequential damages, damages for loss of business profits, business
interruption, loss of business information, or other pecuniary loss, resulting from any violation of the above prohibitions.
Warranty
Honeywell Analytics warrants the Touchpoint Plus system against defective parts and workmanship, and will repair or (at
its discretion) replace any components that are or may become defective under proper usage within 12 months from the
date of commissioning by a Honeywell Analytics approved representative* or 18 months from shipment from Honeywell
Analytics, whichever is sooner.
This warranty does not cover consumable, batteries, fuses, normal wear and tear, or damage caused by accident, abuse,
improper installation, unauthorized use, modification or repair, ambient environment, poisons, contaminants or abnormal
operating conditions.
This warranty does not apply to sensors or components that are covered under separate warranties, or to any 3rd-party
cables and components.
Any claim under the Honeywell Analytics Product Warranty must be made within the warranty period and as soon as
reasonably practicable after a defect is discovered. Please contact your local Honeywell Analytics Service representative
to register your claim.
This is a summary. For full warranty terms please refer to the Honeywell Analytics’ General Statement of Limited Product
Warranty, which is available on request.
* A Honeywell Analytics approved representative is a qualified person trained or employed by Honeywell Analytics, or a
qualified person trained in accordance with this manual.
Copyright Notice
Microsoft, MS and MS–DOS are registered trademarks of Microsoft Corp.
Other brand and product names mentioned in this manual may be trademarks or registered trademarks of their respective
companies and are the sole property of their respective holders.
Honeywell is the registered trademark of Honeywell Automation and Control Systems (ACS).
Touchpoint is a registered trademark of Honeywell Analytics (HA).
Find out more at www.honeywellanalytics.com

Conditions of Use
MAN0984_Iss 3_02/16 Touchpoint Plus
Pt. No. 3011M5001_3 iv Technical Handbook
This page deliberately blank.

Contents
MAN0984_Iss 3_02/16 Touchpoint Plus
Pt. No. 3011M5001_3 v Technical Handbook
Chapter 1. Important Information .......................................................................................... 1
1.1 Regulatory Approval Markings ................................................................................................1
1.2 Additional Product Markings ...................................................................................................1
1.3 TPPL Mandatory Warning.........................................................................................................1
1.4 TPPL General Warnings ...........................................................................................................2
1.5 TPPL General Cautions ............................................................................................................3
1.6 How to Use this Manual............................................................................................................3
1.6.1 Intended Readers..............................................................................................................3
1.6.2 Conventions Used.............................................................................................................3
1.6.3 Associated Manuals..........................................................................................................4
Chapter 2. Safety Hazards, Warnings and Cautions ........................................................... 5
2.1 Safety .........................................................................................................................................5
2.1.1 Warnings and Cautions.....................................................................................................5
2.1.2 Safety Hazards..................................................................................................................6
2.2 Location and Description of Warning Labels.........................................................................8
2.2.1 Safety Warning Labels......................................................................................................8
2.3 Electrical Hazards .....................................................................................................................9
2.3.1 General Safety Precautions..............................................................................................9
2.3.2 Component Testing and Replacement..............................................................................9
2.3.3 Good Practice.................................................................................................................10
2.3.4 Lithium Battery Hazard....................................................................................................10
2.3.5 Training of Personnel......................................................................................................12
2.3.6 Conditions Satisfying Local, National and International Safety Regulations ...................12
2.3.7 Due Authorisation............................................................................................................12
2.3.8 Approved Maintenance and Servicing Procedures.........................................................12
Chapter 3. System General Description.............................................................................. 13
3.1 How to Open and Close the Enclosure .................................................................................15
3.2 Equipment Specification ........................................................................................................16
3.2.1 Power Requirements (Controller Unit only).....................................................................16
3.2.2 Weights...........................................................................................................................17
3.2.3 Dimensions.....................................................................................................................17
3.2.4 Ambient Operating Temperature..................................................................................... 17
3.2.5 Overall Ambient Operating Humidity...............................................................................17
3.2.6 Storage Conditions (Without batteries) ...........................................................................17
3.2.7 Storage Conditions (With batteries) ................................................................................17
3.2.8 IP Rating.........................................................................................................................17
3.2.9 Construction....................................................................................................................17
3.2.10 Touchpoint Plus Packaging...........................................................................................18
3.2.11 Packaging Components for Return to Manufacturer.....................................................18
3.2.12 Disposal (WEEE Directive)............................................................................................18
3.3 TPPL Construction..................................................................................................................18
3.3.1 TPPL Basic Control Unit .................................................................................................18
3.3.2 TPPL Expansion Unit......................................................................................................19
3.3.3 TPPL DIP Switches......................................................................................................... 19
Chapter 4. System Mechanical Installation ........................................................................ 21
4.1 Wall Mounting Requirements................................................................................................. 22
4.1.1 Wall Mount Fixings..........................................................................................................23
Chapter 5. Electrical Power Connection and Interfacing.................................................. 25
5.1 Power Connection................................................................................................................... 25
5.1.1 AC Power Supply............................................................................................................26
5.1.2 DC Power Supply............................................................................................................27
5.1.3 Backup Battery Pack.......................................................................................................27
5.2 Cabling and Connection Requirements................................................................................ 28
5.2.1 AC Mains Voltage Power Cables....................................................................................28
5.2.2 DC Power Cables............................................................................................................28

Contents
MAN0984_Iss 3_02/16 Touchpoint Plus
Pt. No. 3011M5001_3 vi Technical Handbook
5.2.3 Field Device Cables........................................................................................................ 28
5.2.4 Optional Expansion Unit Connection...............................................................................29
5.2.5 Main Module Connections...............................................................................................30
5.2.6 Expansion Module Power Connections...........................................................................31
5.2.7 TPPL DIP Switches......................................................................................................... 32
5.2.8 Ethernet Connection (Option)..........................................................................................32
5.2.9 Module / Field Device Connections.................................................................................33
5.2.10 mA Input Module Connections......................................................................................34
5.2.11 mV Input Module Connections......................................................................................38
5.2.12 Dual Input Module Connections....................................................................................39
5.2.13 mA Output Module Connections ...................................................................................40
5.2.14 Relay Output Module Connections................................................................................41
5.3 Modbus Remote Terminal Unit (RTU) and Transmission Control Protocol (TCP) Connections
42
5.3.1 Modbus Configuration.....................................................................................................44
Chapter 6. Commissioning................................................................................................... 45
6.1 Menu Structure........................................................................................................................ 45
6.1.1 The Information Menu.....................................................................................................45
6.1.2 The Configuration Menu.................................................................................................. 46
6.1.3 The Maintenance Menu ..................................................................................................47
6.1.4 System Test Menu..........................................................................................................47
6.2 First Time Switch On...............................................................................................................48
6.3 Logging In/Out.........................................................................................................................49
6.3.1 How to Log In..................................................................................................................49
6.3.2 How to Log Out...............................................................................................................49
6.3.3 Password Rules..............................................................................................................49
6.3.4 How To Change a Password ..........................................................................................50
6.3.5 Forgotten Passwords......................................................................................................50
6.4 Date, Time and Language Settings ...................................................................................51
6.4.1 How to Set or Change Date, Time and Language Settings.............................................51
6.5 Service Contact Settings........................................................................................................ 51
6.6 Touch Panel Configuration ....................................................................................................52
6.6.1 How to Change the Backlight Timeout and Brightness...................................................52
6.6.2 How to Calibrate the Touch Panel...................................................................................52
6.7 Latching Alarms...................................................................................................................... 52
6.8 Remote Reset / Acknowledge / Inhibit Switch Options........................................................55
6.9 Data Logging........................................................................................................................... 55
6.9.1 To set or change Data Logging:......................................................................................55
6.10 TPPL TCP/IP Address...........................................................................................................56
6.11 Network Settings for WEB and MODBUS TCP....................................................................56
6.12 Modbus RTU Settings...........................................................................................................57
6.13 Commission Input / Output Modules...................................................................................58
6.14 Channel Configuration.......................................................................................................... 58
6.14.1 Introduction ...................................................................................................................58
6.14.2 Configuring a Channel (mA Input and mV Input Channels) ..........................................59
6.14.3 Editing a Configured Channel.......................................................................................60
6.14.4 Editing mA Input Channel Settings................................................................................60
6.14.5 Editing mV Input Channel Settings................................................................................64
6.14.6 Editing Relay Output Channel Settings.........................................................................66
6.15 Calibrating Input Channels...................................................................................................68
6.15.1 Adjusting the mV Sensor Baseline................................................................................69
6.15.2 Calibrating a mV Input Channel ....................................................................................69
6.15.3 Calibrating a mA Input Channel ....................................................................................71
6.16 Backing Up the Configuration Settings...............................................................................73
6.16.1 How to Back Up the Configuration:...............................................................................73
6.16.2 How to Restore the Configuration.................................................................................73

Contents
MAN0984_Iss 3_02/16 Touchpoint Plus
Pt. No. 3011M5001_3 vii Technical Handbook
Chapter 7. Touchpoint Plus User Guide ............................................................................. 75
7.1 User Interface General............................................................................................................ 75
7.2 Touchscreen............................................................................................................................76
7.3 Switching On and Off..............................................................................................................76
7.4 Menu Items and Access Levels .............................................................................................77
7.4.1 Navigation – Active Access Level Icons..........................................................................79
7.5 SD Card Usage ........................................................................................................................79
7.5.1 Checking the Capacity of the SD Card............................................................................79
7.5.2 Inserting or Replacing SD Cards..................................................................................... 80
7.6 Normal Operation (Safety Functions) .................................................................................81
7.7 Operating Overview ................................................................................................................81
7.7.1 Touchscreen ...................................................................................................................81
7.7.2 User Interface Scr een ....................................................................................................81
7.7.3 Navigating the Channel Detail Screens. ............................................................................83
6.6.3 Navigation – Active Events and Filtering ......................................................................84
7.7.4 Navigation – Menu..........................................................................................................85
7.8 Responding to Alar ms.........................................................................................................86
7.8.1 View Active Alarms .......................................................................................................86
7.8.2 Accept or Acknowledge an Active Alarm ....................................................................86
7.8.3 Reset a Latched Alarm ..................................................................................................87
7.9 Event Information ................................................................................................................... 87
7.9.1 Viewing Event Information ..........................................................................................87
7.9.2 Accepting / Acknowledging Active Events.......................................................................87
7.9.3 Resetting Latched Events...............................................................................................88
7.10 Inhibiting Channels...............................................................................................................88
7.10.1 To Inhibit Input Channels:.............................................................................................88
7.10.2 To Clear Inhibits:...........................................................................................................88
7.10.3 To Change Inhibit Timeouts..........................................................................................88
7.11 Viewing Input Channels and Input Details .................................................................... 89
7.12 Viewing Output Channels ..................................................................................................90
7.13 Viewing theTrend Graph ...................................................................................................91
7.14 Viewing and Exporting Event History..................................................................................92
7.14.1 To View the Event History:............................................................................................92
7.14.2 To Export the Event History:.........................................................................................92
7.15 Accessing the System Information and Service Contact Details......................................92
7.16 System State and System Failure Relays ...........................................................................92
7.17 Monitoring TPPL via the Optional Web Interface ............................................................... 93
7.17.1 Web Interface Configuration .........................................................................................93
7.17.2 Web Interface Navigation..............................................................................................95
Chapter 8. Daily / Shift Checks ............................................................................................ 97
Chapter 9. Routine Maintenance and Scheduled Testing................................................. 99
9.1 Routine Maintenance..............................................................................................................99
9.1.1 Weekly Checks ............................................................................................................... 99
9.2 Routine Testing.....................................................................................................................100
9.2.1 Exercising the Audio/Visual Alarms...............................................................................100
9.2.2 Exercising the Relays....................................................................................................101
9.2.3 Checking the mA Outputs.............................................................................................101
9.2.4 Calibrating mV Input Channels......................................................................................102
9.3 Periodic Scheduled Testing.................................................................................................104
9.3.1 Introduction...................................................................................................................104
9.3.2 Field Inputs Test............................................................................................................105
9.3.3 Cause and Effect Test...................................................................................................105
Chapter 10. Repairs, Replacements and Upgrades......................................................... 107

Contents
MAN0984_Iss 3_02/16 Touchpoint Plus
Pt. No. 3011M5001_3 viii Technical Handbook
10.1 How to Decommission and Remove a Serviceable I/O Module ......................................107
10.1.1 To Remove a Serviceable Module..............................................................................107
10.2 How to Replace a Faulty I/O Module..................................................................................108
10.2.1 To Replace a Faulty Module.......................................................................................108
10.3 How to Add a New I/O Module............................................................................................ 109
10.3.1 To Add a New Module.................................................................................................109
10.4 How to Update the Sensor Catalogue ............................................................................... 110
10.4.1 To Update the Sensor Catalogue................................................................................110
10.5 How to Backup / Restore the System Configuration........................................................111
10.5.1 To Create a Backup File .............................................................................................111
10.5.2 To Restore the Configuration From a Backup File......................................................112
10.6 How to Update Firmware ....................................................................................................113
10.6.1 How to Check Firmware Compatibility ........................................................................113
10.6.2 How to Update the Firmware.......................................................................................114
10.7 Back up Battery Maintenance ............................................................................................115
10.7.1 Recommended Backup Battery Maintenance.............................................................115
10.7.2 How to Replace the Backup Battery............................................................................115
10.8 Return to Factory Default Settings....................................................................................116
10.8.1 To Reset the Touchpoint Plus to its Factory Default Settings.....................................116
Chapter 11. Troubleshooting ............................................................................................. 117
11.1 Calling for Technical Support. ...........................................................................................117
Chapter 12. Technical Specifications................................................................................ 119
12.1 Environmental.....................................................................................................................119
12.2 User Interface and Main Module ........................................................................................119
12.3 I/O Modules..........................................................................................................................120
12.3.1 mA Input Module.........................................................................................................120
12.3.2 mV Input Module.........................................................................................................120
12.3.3 Dual Input Module.......................................................................................................120
12.3.4 mA Output Module......................................................................................................121
12.3.5 Relay Output Module ..................................................................................................121
12.3.6 Expansion Module.......................................................................................................121
12.4 Power Supplies....................................................................................................................121
12.4.1 External Supplies........................................................................................................121
12.4.2 Backup Battery............................................................................................................122
12.5 Enclosures........................................................................................................................... 122
12.5.1 Wall Mount Enclosure.................................................................................................122
Chapter 13. Certifications................................................................................................... 123
13.1 EC Declaration of Conformity ............................................................................................123
13.2 National and International Certificates of Compliance.................................................... 124
Chapter 14. Replacement Parts and Optional Extras...................................................... 125
14.1 Spare Parts..........................................................................................................................125
14.2 Publications......................................................................................................................... 126
Chapter 15. TPPL Configuration Code.............................................................................. 129
Chapter 16. Icon Glossary.................................................................................................. 131
Chapter 17. Compatible Sensors....................................................................................... 133
Chapter 18. Configurable Parameter Reference Guide................................................... 135
Chapter 19. Fault Codes ..................................................................................................... 139
Chapter 20. List of Figures................................................................................................. 141
Chapter 21. List of Tables................................................................................................... 143

Important Information
MAN0984_Iss 3_02/16 Touchpoint Plus
Pt. No. 3011M5001_3 1 Technical Handbook
Chapter 1. Important Information
The Equipment referred to in this manual contains components and assemblies that are each certified for use in a variety
of differing environments, and it is the site owner’s responsibility to confirm the suitability of the equipment prior to its
installation and use.
The Equipment assemblies referred to in this manual are collectively certified for use in a flammable gas detection system
only. Any other use is not currently certified and is not authorised by the manufacturer.
Please check the product rating plate and look for the following marks to ensure that the supplied equipment is suitable for
its intended location and purpose:
1.1 Regulatory Approval Markings
Products bearing the CE mark conform to all applicable European Directives as stated on the Honeywell product specific
EC Declaration of Conformity.
Products bearing the UL mark conform to the requirements for Ordinary Locations. The letters C and US mean that the
product is additionally certified for use in Canada and the United States of America.
1.2 Additional Product Markings
Products bearing this mark must not be disposed of in domestic waste. They must always be taken to a specialist Waste
Electrical and Electronic Equipment (WEEE) disposal or recycling facility. A box under the mark may show the type of
hazardous material in the product, e.g. the letters Pb would show that the item contains Lead.
Products bearing this mark are recyclable and should not be disposed of as normal landfill waste.
1.3 TPPL Mandatory Warning
WARNING
FOR SAFETY REASONS THIS EQUIPMENT MUST BE OPERATED BY QUALIFIED PERSONNEL
ONLY. READ AND UNDERSTAND THE INSTRUCTION MANUAL COMPLETELY BEFORE
OPERATING OR SERVICING THE EQUIPMENT.
ATTENTION
POUR DES RAISONS DE SÉCURITÉ, CET ÉQUIPEMENT DOIT ÊTRE UTILISÉ, ENTRETENU ET
RÉPARÉ UNIQUEMENT PAR UN PERSONNEL QUALIFIÉ. ÉTUDIER LE MANUEL D’INSTRUCTIONS
EN ENTIER AVANT D’UTILISER, D’ENTRETENIR OU DE RÉPARER L’ÉQUIPEMENT.

Important Information
MAN0984_Iss 3_02/16 Touchpoint Plus
Pt. No. 3011M5001_3 2 Technical Handbook
1.4 TPPL General Warnings
1) The equipment specified in this manual is only to be installed by the Manufacturer’s trained personnel, or by
competent persons trained in accordance with the Manufacturer’s installation instructions.
2) Installation must be in accordance with the recognized standards of the appropriate authority in the country
concerned. Refer to local, national and company regulations.
3) Do not operate the Touchpoint Plus system or its components outside of their rated operating specification.
4) Touchpoint Plus must not be operated in Oxygen enriched atmospheres, i.e. greater than 25% v/v Oxygen.
5) All equipment containing a User Interface must be suitably protected from direct sunlight and rain.
6) Power Supply Fluctuations are not to exceed DC 18 – 32 V SELV Supply or ±10 % of nominal.
7) All versions of Enclosure apparatus are electrical Class 1, and must be connected to Protective Earth (Ground).
8) The Touchpoint Plus installation must include a means of isolating or disconnecting the input voltage supply.
The isolation or disconnection device must be conveniently located close to the system and be clearly labelled.
For an AC mains voltage supply, the isolation or disconnection device must disconnect both the line and
neutral poles, but maintain earth (ground) continuity.
9) The Touchpoint Plus input voltage supply must include over-current protection.
10) All cabling must be appropriately rated and approved in accordance with local, national and company
regulations, and suitable for the installation. Additionally, cabling must satisfy requirements defined in the
manuals of connected field devices, in particular if the field device is certified for use in a hazardous location.
11) All signal cables and interconnections must be shielded and the shields terminated only at the unified earth
(ground) bus bar situated inside the enclosure
12) All conduits and cable armour shall be bonded to protective earth (ground), and care must be taken to avoid
ground loops and to avoid contact with cable shielding.
13) Cable entry glands, blanking plugs, reducers, adaptors and breather devices must be suitably approved and
must not reduce the IP rating or protection levels. Items should not be used if there is a high risk of mechanical
damage to the equipment or enclosure.
14) Access doors and entry points must be kept closed when the system is energised in normal operation.
15) The TPPL Enclosures must be securely closed and the locking handle security screws must be fully tightened
during normal operation.
16) All equipment in this manual is rated to +2000 m (6562 ft) altitude maximum.
17) For safety reasons this equipment must be operated by qualified personnel only. Read and understand the
Instruction Manual completely before operating or servicing the equipment.
18) Touchpoint Plus systems may contain hazardous live terminals. Appropriate precautions should be taken
during operation, installation, and maintenance and servicing. Specifically, operators must have appropriate
training and experience to be aware of the hazards to which they may be exposed, and of measures to
minimise risk to themselves or other people.
19) The protection provided by TPPL may be impaired or lost if the equipment is installed or used in an incorrect,
unspecified or unauthorised way.
20) Be aware that extended exposure of a detector element to certain concentrations of combustible gases and air
can introduce stress to the element that may seriously affect its performance, and therefore recalibration should
be carried out or the sensor replaced, or both, after an alarm due to an indication of a high concentration.
21) When used in a Gas Detection summing up role, the gas reading may be higher than the actual concentration
at any one detector head location, or it may be the actual concentration at one specific detector head.
22) Exposure to some chemicals may degrade the sealing properties of materials used in the alarm relay.
23) Do not open TPPL enclosures or disconnect/reconnect equipment until power has been isolated and the area
is made safe / non-hazardous. This includes replacing backup batteries.
24) Substitution of any components may impair suitability for Class I, Division 2.

Important Information
MAN0984_Iss 3_02/16 Touchpoint Plus
Pt. No. 3011M5001_3 3 Technical Handbook
1.5 TPPL General Cautions
1.6 How to Use this Manual
1.6.1 Intended Readers
This Manual should be read by everyone who operates or monitors the Touchpoint Plus gas detection system.
Only personnel who have been fully trained by Honeywell are authorised to Install, Set-up, Service, and Test, Repair, or
Recondition Honeywell gas detection systems.
1.6.2 Conventions Used
The following conventions are used in this manual:
Boot up refers to the action of starting the software from cold.
Menu>Configuration>Channel highlights a sequence of commands (including button touches).
mV Sensor refers to a mV Bridge Sensor.
Reboot refers to shutting down and restarting the software without interrupting the power supply.
Restart refers to cycling the power off and then on again.
SELV refers to Safety Extra-Low-Voltage devices.
[Start] highlights unique button touches.
Start up refers to the action of switching on the system.
Touch refers to all direct interactions with the Touchscreen, whether by finger or stylus.
TPPL refers to the Touchpoint Plus Gas Detection System.
1) Touchpoint Plus SMPS, Input and Output Modules have no user serviceable parts. In the unlikely event of a
failure, the item must be replaced using only manufacturer supplied parts.
2) Do not use sharp objects to operate the Touchscreen as this could irreparably damage the User Interface and
adversely affect its IP rating.
3) Use only soft, damp cloths or screen wipes to clean the Touchpoint Plus. Do not use solvents or abrasives as
they will cause irreparable damage.
4) Once commissioned, Touchpoint Plus is intended for continuous operation.
5) Undo the security screws before pulling the locking handle. Failing to do so may irreparably damage the
enclosure.
6) Do not place any objects on top of the enclosures as this may cause overheating and may cause the enclosure
to fall from the wall.
IMPORTANT
Personnel, who work on, or in the area of, the Touchpoint Plus Gas detection system must be made aware of the
contents of Chapter 2 – Safety Hazards, Warnings and Cautions.
Before unpacking the system, please read the documentation that accompanies it.

Important Information
MAN0984_Iss 3_02/16 Touchpoint Plus
Pt. No. 3011M5001_3 4 Technical Handbook
1.6.3 Associated Manuals
This TPPL Technical Handbook should be used in conjunction with ancillary component and field device user guides or
documentation.
This TPPL Technical Handbook (MAN 0984) is available in the following languages:
•Chinese (Simplified) Pt. Nr. 3011M5013
•Dutch Pt. Nr. 3011M5014
•English (UK) Pt. Nr. 3011M5001
•French (Canada) Pt. Nr. 3011M5015
•French (France) Pt. Nr. 3011M5016
•German Pt. Nr. 3011M5017
•Italian Pt. Nr. 3011M5018
•Japanese Pt. Nr. 3011M5019
•Korean Pt. Nr. 3011M5020
•Portuguese (Brazil) Pt. Nr. 3011M5021
•Portuguese (Portugal) Pt. Nr. 3011M5022
•Russian Pt. Nr. 3011M5023
•Spanish (Mexico) Pt. Nr. 3011M5024
•Spanish (Spain) Pt. Nr. 3011M5025
•Swedish Pt. Nr. 3011M5011
•USA (English) Pt. Nr. 3011M5012
The supplementary TPPL Modbus Installation and Setup Guide (#3011M5027) is available in English only, and is
recommended for OEMs and Modbus specialists only.

Safety Hazards, Warnings And Cautions
MAN0984_Iss 3_02/16 Touchpoint Plus
Pt. No. 3011M5001_3 5 Technical Handbook
Chapter 2. Safety Hazards, Warnings and Cautions
2.1 Safety
Incorrect set-up, maintenance, operation or modification of the Touchpoint Plus gas detection system or its installation
may constitute a serious hazard to the health and safety of personnel and their environment. It is therefore imperative that
the contents of this chapter are thoroughly understood by everyone who has access to the gas detection system or its
associated equipment.
When properly installed, this gas detection system enclosure is rated as IP65.
It may be installed in a Pollution Degree 2 (i.e. laboratory, office or control room) or Pollution Degree 3 (i.e. unheated
boiler room) environment as defined by IEC/UL/EN 61010–1: Safety requirements for electrical equipment for
measurement, control and laboratory use.
In all cases, several hazards may be present when operating or servicing the equipment and extreme caution must be
exercised at all times. The hazards that may be encountered include:
•Class 1 electrical hazards (AC 110/220 V, DC 18–32 V)
•Mechanical hazards (Heavy components, swinging access doors, locking handles etc.)
•Environmental hazards (toxic atmospheres)
•Fire and Ignition hazards
2.1.1 Warnings and Cautions
Safety of this equipment is reinforced by the use of safety labels that are fixed to the equipment in a visible manner. The
labels used and their location is detailed in Ch.2.2.1 Safety Warning Labels.
Other likely hazard occurrence and severity is indicated throughout this manual by the use of signal words accompanied
by a hazard description and an internationally recognisable hazard symbol, as shown in the three example boxes below:
DANGER
Danger indicates an imminent hazard that, if not avoided, is extremely likely to result in death or serious injury.
WARNING
Warning indicates a potentially hazardous situation that, if not avoided, could result in death or serious injury.
CAUTION
Caution indicates a potentially hazardous situation that, if not avoided, may result in minor or moderate injury.
It is also used to alert the user against unsafe working practices and potential damage to equipment.
DANGER
Touchpoint Plus is not ATEX/IECEx certified,and it shall only be installed in safe areas where there are no
flammable atmospheres, and where oxygen concentrations cannot exceed 25% v/v O2.
Touchpoint Plus is suitable for use in Class I, Division 2, Groups A, B, C, and D, or non-hazardous locations only.

Safety Hazards, Warnings And Cautions
MAN0984_Iss 3_02/16 Touchpoint Plus
Pt. No. 3011M5001_3 6 Technical Handbook
2.1.2 Safety Hazards
The following specific hazards are associated with the installation and use of this equipment:
WARNING – TOXIC WASTE AND HARMFUL BY-PRODUCTS
The Touchpoint Plus system and/or its sensors may become contaminated by the ambient environment in which
it or they are used. It is the Customer’s sole responsibility to ensure that all appropriate safety precautions are
taken before handling any components or transferring them to any other party.
WARNING – LETHAL VOLTAGE PRESENT
All power supplies must be hard wired and must include a circuit breaker (RCD / RCCB) and, close by and
unobstructed, a means of manually isolating and locking–out the power supply without breaking the protective
earth (ground) connection.
Removable plug/socket connection is not permitted under any circumstance.
WARNING – LETHAL VOLTAGE PRESENT
Lethal current may be present in this equipment when electrical power is applied and after it is removed. There is
a risk of death or injury from electrical shock when access doors are open.
Isolate power before opening electrical access panels. Ensure residual current is fully discharged before touching
live terminals.
WARNING – LITHIUM BATTERY HAZARDS
Lithium batteries may cause severe injury or death if swallowed, and may catch fire or explode if mishandled,
recharged, burned or disposed of incorrectly.
Always handle batteries with care, keep them out of the reach of children, and dispose of them carefully in
accordance with local regulations.
Batteries (regardless of type) shall only be handled, fitted, removed or replaced in non-hazardous (safe) areas.
DANGER – IGNITION HAZARD
Touchpoint Plus is Not ATEX/IECEx certified, and it shall only be installed in safe areas where there are no
flammable atmospheres, and where oxygen concentrations cannot exceed 25% v/v O2.
Touchpoint Plus is suitable for use in Class I, Division 2, Groups A, B, C, and D or non-hazardous locations only.
WARNING – LETHAL VOLTAGE PRESENT
Lethal current may be generated both internally and externally to the system. All installations, including
enclosures and external units, must be grounded to protective earth, and must be capable of staying earthed
(grounded) when the power supply is interrupted.
The Protective Earth (Ground) symbol is shown to the left, and it always has a green background. Do not confuse
it with the chassis earth and equipment earth symbols shown below it.

Safety Hazards, Warnings And Cautions
MAN0984_Iss 3_02/16 Touchpoint Plus
Pt. No. 3011M5001_3 7 Technical Handbook
2.1.2 Safety Hazards (Cont.)
The following general hazards are associated with the use of this equipment:
WARNING – DO NOT USE WATER
DO NOT USE WATER if a lithium battery overheats or burns, as it may make the fire worse and it may cause an
explosion.
Evacuate the area immediately and call Emergency Services.
CAUTION – HEALTH AND ENVIRONMENTAL HAZARDS
This equipment contains a number of potentially toxic substances that may pose a health or environmental
hazard if exposed to very high temperatures, VOCs or corrosives, or if improperly handled or disposed of.
WARNING – FIRE OR EXPLOSION HAZARD
Batteries may explode if mistreated. Do not disassemble them or dispose of in fire.
CAUTION – RISK OF INJURY OR DAMAGE
Always follow a Safe System of Work when carrying out any work involving Safety Systems.
CAUTION – RISK OF EQUIPMENT DAMAGE
Touchpoint Plus houses static-sensitive components. Always isolate power and discharge circuits before
touching internal components. Always take anti-static precautions.
CAUTION – RISK OF HEARING DAMAGE
Touchpoint Plus can be used to control loud alarms and sirens. Always wear hearing protection when working in
the vicinity of loud or high-pitched noises.
CAUTION – RISK OF EYE INJURY
Touchpoint Plus uses high energy AC and DC currents that may cause arcing and sparks if shorted out. Always
wear eye protection when the enclosure is open.
CAUTION – RISK OF INJURY AND DAMAGE
Each Touchpoint Plus enclosure is heavy and weighs considerably more when packed. Ensure that a Manual
Handling Risk Assessment is carried out before moving or installing the system, and ensure that enclosures are
fitted securely to a suitable vertical surface. Do not place objects on the enclosures.

Safety Hazards, Warnings And Cautions
MAN0984_Iss 3_02/16 Touchpoint Plus
Pt. No. 3011M5001_3 8 Technical Handbook
2.2 Location and Description of Warning Labels
2.2.1 Safety Warning Labels
In accordance with the requirements of European Standard EN 60825–1, appropriate warning labels are mounted in
specified locations on the equipment. This is to indicate conditions under which the user could be subjected to electrical
hazards.
Figure 1. Quick Start Guide Label
(Not to Scale) Figure 2. Rating Label (External – Not Shown Below)
Figure 3. Protective Earth (Ground) Point Figure 4. Equipment Earth (Ground) Point
This Protective Earth (Ground) location point label is
used inside the system and is not normally visible to
the operator.
This Equipment Earth (Ground) location point label is
used inside the system and is not normally visible to
the operator.
Figure 5. Internal Label Positions

Safety Hazards, Warnings And Cautions
MAN0984_Iss 3_02/16 Touchpoint Plus
Pt. No. 3011M5001_3 9 Technical Handbook
2.3 Electrical Hazards
Gas detection systems contain electrical supplies that are potentially dangerous and hence suitable precautions must
be taken to prevent the risk of electrocution. This is especially important when untrained/unqualified persons are
allowed to open the enclosure (e.g. to access/remove/refit the SD Card).
2.3.1 General Safety Precautions
•Read the relevant manual before beginning any operating or service procedures.
•Only personnel trained and certified by Honeywell are authorised to service, fit or remove internal parts.
•Only the minimum number of trained personnel, consistent with safety, should have access to the area while work is
being carried out. If necessary, erect warning signs and barriers.
•Follow accepted working procedures and codes of practice as well as the electrical safety code for the site where the
equipment is installed.
•Never operate the equipment under normal conditions with doors open, access panels removed or shorting links
fitted.
•Do not ‘Live Test’ without a Safe System of Work (SSoW).
•Always keep the area around the equipment dry and free of obstructions.
•Switch off and Isolate the equipment if water ingress is suspected or confirmed.
•Never operate the equipment if any Mains power cable is frayed or damaged.
•Never wear wristwatches, rings, bracelets, or other jewellery when working around electrical circuits or moving parts.
•Take anti-static precautions when working on electronic circuits.
•Never work on electrical equipment alone.
2.3.2 Component Testing and Replacement
Before carrying out any electrical testing or component replacement:
•Read this Manual to become familiar with the location of high voltage components.
•Isolate the system at the main circuit breaker, lock it in the ‘Off’ position, and attach a notice indicating that
maintenance work is in progress.
•Always wait for 5 minutes after isolating the equipment to ensure that stored energy has dissipated.
•Never assume the polarity of cabling or replacement components. Refer to electrical schematics or contact Honeywell
for confirmation.
•Use only Honeywell approved replacement parts.
WARNING – UNAUTHORISED PERSONNEL
Only Honeywell trained and certified maintenance technicians are authorised to carry out component testing and
replacement. Unauthorised work may result in a potentially dangerous situation and will invalidate the
manufacturer’s warranty.
ANTI–STATIC PRECAUTIONS
Antistatic Precautions are required to prevent severe damage to electronic components.

Safety Hazards, Warnings And Cautions
MAN0984_Iss 3_02/16 Touchpoint Plus
Pt. No. 3011M5001_3 10 Technical Handbook
Antistatic Precautions
As with all modern electronic circuits, the Printed Circuit Boards (PCBs) in Touchpoint Plus systems utilise some static-
sensitive components that can be severely damaged if subjected to static discharge. Static can be generated on the
human body by friction or movement and is discharged through the first contacted route to earth. It can also jump gaps
between items of differing electrical potential.
Static damage is not always immediately apparent and can cause component failure at any time after the static discharge
has occurred. It is, therefore, very important that everyone takes the following precautions when handling PCBs:
•An industry approved antistatic wrist strap, containing a resistive component greater than 1Megohm, must be worn
and connected to an effective earth (ground) point. The continuity between the strap and earth (ground) must be
checked regularly.
•PCBs must only be handled by their non-conductive edges. Do not allow any components, conductive tracks or
contacts to come into proximity with the body, clothing, machinery, power source or any material other than a static-
dissipative mat.
•With the exception of assemblies containing batteries, anti-static packaging must be used for transporting PCBs and
Integrated Circuits (ICs). All Touchpoint Plus electronic components are shipped in appropriate packaging that can be
re-used when returning items for test or repair.
•Avoid wearing clothing manufactured from, or containing a high proportion of, man-made fibres. These can build up a
high static potential that may not be discharged through the body or wrist strap.
An effective earth (ground) point is the protective earth (ground) bus bar inside the enclosure. This can be used to connect
a suitable anti-static wrist strap provided that the Gas detection system is connected to protective earth (ground) via the
mains power supply cable.
2.3.3 Good Practice
After switching off the system, it is good practice to wait at least 15 seconds before switching it on again. This allows the
circuits and RAM to discharge adequately before being powered-up again. Failing to do so may cause data corruption.
2.3.4 Lithium Battery Hazard
Lithium batteries are fitted to Touchpoint Plus as backup power sources.
Replace the factory installed battery pack TPPLOIBB with Honeywell Analytics Asia Pacific replacement battery pack part
no. TPPLSIBB and the PCB CMOS battery with type CR2032 only.
Use of other batteries may present a risk of fire or explosion.
IMPORTANT
If installed correctly, the equipment earth (ground) point is connected directly to mains earth (ground) via
protective earth and the mains power supply cable, and the earth (ground) circuit cannot be broken by operating
the Isolator switch or circuit breaker.
LITHIUM BATTERY TOXIC AND FIRE HAZARDS
Lithium batteries may cause severe injury or death if swallowed, and may catch fire or explode if mishandled,
recharged, burned or disposed of incorrectly.
Always handle lithium batteries with care, keep them out of the reach of children, and dispose of them carefully
in accordance with local regulations.
Batteries shall only be fitted, removed or replaced in non-hazardous (safe) areas.

Safety Hazards, Warnings And Cautions
MAN0984_Iss 3_02/16 Touchpoint Plus
Pt. No. 3011M5001_3 11 Technical Handbook
Product Compliance
This product complies with the following standards and directives.
Other safety directives may apply to the complete system installation if an OEM’s product is integrated into other
equipment or machinery.
Safety Compliance
Hazardous Location
(Non-Incendive)
Class 1, Division 2, Groups A,B,C,D, Temp. Code T4
ISA 12.12.01-2013
CSA C22.2 No. 213-M1987
Electrical Safety CAN/CSA C22.2 No. 61010-1 and No.142
UL 61010–1 (3rd Edition); UL508
IEC/EN 61010–1 (3rd Edition)
EMC/RFI EN 50270
Low Voltage Directive IEC/EN 61010–1 (3rd Edition)
Gas Performance* ISA 12.13.01 and CSA C22.2 No. 152
* ISA 12.13.01 and CSA C22.2 No.152 approvals are applicable only to mV sensors Model 705 and MPD or any suitably
certified mA sensor.
Note: The Equipment referred to in this manual contains components and assemblies that are each certified for use in a
variety of differing environments, and it is the site owner’s responsibility to confirm the suitability of the equipment prior to
its installation and use.
Please check the product rating plate and look for the following marks to ensure that the supplied equipment is
suitable for its intended location and purpose:
Products bearing the CE mark conform to all applicable European Directives as stated on the Honeywell product specific
EC Declaration of Conformity.
Products bearing the UL mark conform to the requirements for Ordinary Locations. The letters C and US mean that the
product is certified for use in Canada and the United States of America.
IMPORTANT
Read and understand the instruction manual before operating or servicing the equipment.

Safety Hazards, Warnings And Cautions
MAN0984_Iss 3_02/16 Touchpoint Plus
Pt. No. 3011M5001_3 12 Technical Handbook
Conditions of Use
This Touchpoint Plus equipment shall only be operated:
•By properly trained personnel.
•Under Honeywell approved conditions.
•With due authorisation.
•Using approved maintenance and servicing procedures.
2.3.5 Training of Personnel
Honeywell and / or its distributors can provide training for operators and maintenance personnel. Personnel who have
been trained in operation and maintenance shall be limited to carrying out only those procedures and tasks taught during
the training course. Honeywell certified maintenance technicians must carry out all other tasks.
Honeywell can also provide additional or advanced training. Retraining is recommended periodically and whenever the
equipment / installation is changed or upgraded.
2.3.6 Conditions Satisfying Local, National and International Safety Regulations
Approved conditions must satisfy the requirements of applicable national and international safety standards and statutory
requirements relating to electrical, EMC, and health hazards. In addition, they must satisfy the requirements of the Site
Safety Officer and the local safety regulations.
2.3.7 Due Authorisation
Before any production, maintenance, or servicing procedure is carried out; written authorisation must be obtained from
one of the following personnel to confirm that the proposed task satisfies the necessary safety conditions:
•A competent authorised person having a professional qualification in an appropriate technical discipline.
•The Factory, Technical or Engineering Manager responsible for the working area.
•The Site Safety Officer or an authorised Honeywell representative or approved distributor.
2.3.8 Approved Maintenance and Servicing Procedures
Approved Maintenance and Servicing Procedures are those stipulated in this manual or as authorised separately by
Honeywell.
It may be necessary to establish a temporary Locally Controlled Area (LCA) to restrict access during maintenance, testing
or servicing of this equipment.