Honeywell PRO3200 Operator's manual

October 2013 © 2013 Honeywell. All rights reserved. 800-15494
PRO3200
(PRO32IC)
Intelligent Controller
Installation and Configuration Guide

Copyright © 2013 Honeywell. All rights reserved.
All product and brand names are the service marks, trademarks, registered trademarks, or registered service
marks of their respective owners. Printed in the United States of America. Honeywell reserves the right to
change any information in this document at any time without prior notice.
WIN-PAK® is a trademark of Honeywell, Inc.
Ordering Information
Please contact your local Honeywell representative or visit us on the web at www.honeywellaccess.com for
information about ordering.
Feedback
Honeywell appreciates your comments about this manual. Please visit us on the web at www.honeywellac-
cess.com to post your comments.

PRO3200 (PRO32IC) Installation and Configuration Guide, Document 800-15494 iii
CONTENTS
1 Notices .......................................................................................................................... . . . . . . . . . 2
1.1 Warnings and Cautions ............................................................................... . . . . . . . . . . 2
1.2 Damage During Shipment ........................................................................... . . . . . . . . . . 3
1.3 Electro Static Discharge............................................................................... . . . . . . . . . . 3
1.4 Disclaimer – Product Liability; Mutual Indemnification ....................... . . . . . . . . . . 4
1.5 Unpacking Procedure .................................................................................. . . . . . . . . . . 4
1.6 Shipping Instructions
................................................................................... . . . . . . . . . . 5
1.7 Limited Warranty
......................................................................................... . . . . . . . . . . 5
1.8 Confidentiality
.............................................................................................. . . . . . . . . . . 6
1.9 Compliance .................................................................................................... . . . . . . . . . . 7
2 Product Overview..................................................................................................... . . . . . . . . . 8
2.1 PRO3200 and PRO2200 .............................................................................. . . . . . . . . . . 8
2.2 Port Settings................................................................................................... . . . . . . . . . . 8
2.3 Other................................................................................................................ . . . . . . . . . . 8
3 Setting Up the PRO3200 Hardware................................................................... . . . . . . . . 10
3.1 Setting the Jumpers....................................................................................... . . . . . . . . . 10
3.2 Setting the DIP Switches ............................................................................. . . . . . . . . . 11
3.3 Technical Specifications .............................................................................. . . . . . . . . . 13
3.4 Status LEDs .................................................................................................. . . . . . . . . . 14
3.5 Supplying Power to the PRO3200 Interface............................................. . . . . . . . . . 15
3.6 Communications Wiring.............................................................................. . . . . . . . . . 16
3.7 Cabinet Tamper and Power Failure Input Wiring.................................... . . . . . . . . . 16
3.8 Memory and Real Time Clock Backup Battery ....................................... . . . . . . . . . 16
4 System Configuration via Web Interface ....................................................... . . . . . . . . 17
4.1 Connecting to ACDSM for the First Time................................................ . . . . . . . . . 17
4.2 Login Page ..................................................................................................... . . . . . . . . . 17
4.3 Home Page ..................................................................................................... . . . . . . . . . 18
4.4 Network Settings........................................................................................... . . . . . . . . . 19
4.5 Host Port......................................................................................................... . . . . . . . . . 20
4.6 Device Information ....................................................................................... . . . . . . . . . 24
4.7 User Configuration........................................................................................ . . . . . . . . . 25
4.8 Restore Default Screen................................................................................. . . . . . . . . . 26
4.9 Apply Setting Screen.................................................................................... . . . . . . . . . 27
4.10 Log Out......................................................................................................... . . . . . . . . . 27

iv www.honeywell.com
(This page is left blank intentionally for double-sided printing.)

PRO3200 (PRO32IC) Installation and Configuration Guide, Document 800-15494 v
LIST OF FIGURES
Figure 1: PRO3200 Connections, LEDs, and DIP Switches . . . . . . . . . . . . . . . . . . 9
Figure 2: PRO3200 Power Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Figure 3: PRO3200 Port Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Figure 4: PRO3200 TMP and FLT Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Figure 5: PRO3200 Web Server Login Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Figure 6: PRO3200 Web Server Home Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Figure 7: PRO3200 Web Server Network Settings Screen . . . . . . . . . . . . . . . . . . 19
Figure 8: PRO3200 Host Port Configuration Screen with IP Server Connection . 20
Figure 9: PRO3200 Host Port Configuration Screen with IP Client Connection . 22
Figure 10: PRO3200 Host Port Configuration with Serial RS-232 Connection . . 23
Figure 11: PRO3200 Web Server Device HW Info Screen . . . . . . . . . . . . . . . . . 24
Figure 12: PRO3200 Web Server User Info Screen . . . . . . . . . . . . . . . . . . . . . . . 25
Figure 13: PRO3200 Web Server Restore Default Screen . . . . . . . . . . . . . . . . . . 26
Figure 14: PRO3200 Web Server Apply Setting Screen . . . . . . . . . . . . . . . . . . . 27

PRO3200 (PRO32IC) Installation and Configuration Guide, Document 800-15494 vi
LIST OF TABLES
Table 1 PRO3200 Jumper Settings ........................................................................................... 10
Table 2 PRO3200 DIP Switch Settings ..................................................................................... 11
Table 3 PRO3200 Technical Specifications ..............................................................................13
Table 4 PRO3200 Status LED Combinations During Initialization ......................................... 14
Table 5 PRO3200 Status LED Combinations During Run Time .............................................. 15

PRO3200 Installation and Configuration Guide, Document 800-15494 1
PRO3200 Installation
In this chapter...
Notices 2
Product Overview 8
Setting Up the PRO3200 Hardware 10
System Configuration via Web Interface 17

2www.honeywell.com
PRO3200 Installation
Notices
1 Notices
1.1 Warnings and Cautions
Note: See the Remote Enclosure Installation Manuals PPRO22ENC1, PRO22ENC2,
PRO22ENC3 or PRO22ENC5 for installation instructions.
Before Installation
Warning: Before installation, TURN OFF the external circuit breaker which supplies
power to the system.
Before connecting the device to the power supply, verify that the output voltage is
within specifications of the power supply (see 'Technical Specifications' on page 13).
Do not apply power to the system until after the installation has been completed.
Personal injury or death can occur, and the equipment can be damaged beyond repair,
if this precaution is not observed.
Fire Safety and Liability Notice
Warning: Never connect card readers to any critical entry, exit door, barrier, elevator or
gate without providing an alternative exit in accordance with all the fire and
life safety codes pertinent to the installation.
These fire and safety codes vary from city to city and you must get approval from
local fire officials whenever using an electronic product to control a door or other
barrier. Use of egress buttons, for example, may be illegal in some cities. In most
applications, single action exit without prior knowledge of what to do is a life safety
requirement. Always make certain that any required approvals are obtained in writing.
DO NOT ACCEPT VERBAL APPROVALS SINCE THEY ARE NOT VALID.
Honeywell never recommends using the PRO3200 or related products for use as a
primary warning or monitoring system. Primary warning or monitoring systems
should always meet the local fire and safety code requirements. The installer must also
test the system on a regular basis by instructing the end user in appropriate daily
testing procedures. Failure to test a system regularly could make the installer liable for
damages to the end user if a problem occurs.
Earth Grounding
Warning: EARTH ground all enclosures for proper installation.
Use Suppressors
Warning: Use suppressors on all door strikes. Use S-4 suppressors for installation.
Honeywell recommends only DC strikes.

PRO3200 Installation
Notices
PRO3200 Installation and Configuration Guide, Document 800-15494 3
UL Warnings
Warning: Wiring methods shall be in accordance with the National Electrical Code
(ANSI/NFPA70):
• All interconnecting devices must be UL Listed.
• Not Evaluated by UL for fire, life safety, or burglary applications.
• Do Not Connect To A Receptacle Controlled By A Switch.
• All interconnecting wire must be UL/ULC Listed, rated and suitable for
the use.
• The battery leads and primary AC main power wiring is non-power
limited. This wiring must be separated from all other wiring by at least
.25" and cannot be installed in the same conduit as any other power
limited wiring.
• Replacement 3 volt lithium coin cell must be one of the following:
– Rayovac: BR2325 or BR2335-B
• The system must be configured to activate an alarm or trouble signal.
Failure to do so will not allow the access function to operate in the event
of a tamper.
1.2 Damage During Shipment
Caution: IF ANY DAMAGE TO THE SHIPMENT IS NOTICED, A CLAIM MUST
BE FILED WITH THE COMMERCIAL CARRIER RESPONSIBLE FOR THE
DAMAGE.
1.3 Electro Static Discharge
Caution: Electro-static discharge (ESD) can damage CMOS integrated circuits and
modules.
To prevent damage always follow these procedures:
• Use static shield packaging and containers to transport all electronic
components, including completed reader assemblies.
• Handle all ESD sensitive components at an approved static-controlled
workstation. These workstations consist of a desk mat, floor mat and an ESD
wrist strap. Workstations are available from various vendors.
Note: This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment.This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
installation and user guides, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his own expense.

4www.honeywell.com
PRO3200 Installation
Notices
Note: This document and the data in it shall not be duplicated, used or disclosed to
others for procurement or manufacturing, except as authorized by and with the written
permission of Honeywell.The information contained in this document or in the
product itself is the exclusive property and trade secrets of Honeywell. Copyright laws
of the United States protect all information in this document or in the software product
itself.
Note: Any use of this product is subject to the terms and acceptance of the Honeywell.
Software Agreement. Please request a copy from Honeywell
(http://www.honeywellaccess.com), and review the agreement carefully.
1.4 Disclaimer – Product Liability; Mutual Indemnification
If a Customer receives a claim that a Product or any component thereof has caused
personal injury or damage to the property of others, Customer shall immediately
notify Honeywell in writing of all such claims. Honeywell shall defend or settle such
claims and shall indemnify and hold Customer harmless for any costs or damages
including reasonable attorneys’ fees which Customer may be required to pay as a
result of the defective Product or the negligence of Honeywell, its agents, or its
employees.
Customer shall hold harmless and indemnify Honeywell from and against all claims,
demands, losses and liability arising out of damage to property or injury to persons
occasioned by or in connection with the acts or omissions of Customer and its agents
and employees, and from and against all claims, demands, losses and liability for costs
of fees, including reasonable attorneys’ fees, in connection therewith.
1.5 Unpacking Procedure
Caution: If any damage to the shipment is noticed before unpacking, a claim must be
filed with the commercial carrier.
All containers should be opened and unpacked carefully in order to prevent damage to
the contents.
Follow these steps to unpack equipment in preparation for installation:
1. Open the container and remove the unit(s) and all packing material. Retain the
container and all the packing materials. They may be used again for
reshipment of the equipment, if needed.
2. Inspect the contents to see if anything is missing. If you notice any missing
items, contact the order entry department at 1-800-323-4576 and follow the
prompts.
3. Visually check the contents. If you see any damage, do the following:
a. If shipping has caused damage to the unit, a claim must be filed with the
commercial carrier.
b. If any other defect is apparent, call for a return authorization.