Honeywell HVC0001 User manual

Owner’s Guide
Guide du propriétaire
Guía del usuario
HVC0001 / HVC0002
Programmable Bath Fan Control
Contrôleur de ventilateur programmable
Controlador de ventilador programable

HVC0001/HVC0002
3
ENGLISH
Quick reference
The LED illuminates
when the bath fan is On.
Press the Main Button to turn the
bath fan On or Off. (Press for 3
seconds to enter the setup menus.)
Press either button to place in
Countdown Mode. Then press the
left button to decrease the
countdown time or the right button
to increase the time.
Setup menu
Clock
The bath fan is On The bath fan is Off
Programmable modes
Countdown time
If the controller is also used to control
lights, pull out this safety tab before
replacing the light bulb. Push back in
after the light bulb is replaced.
Countdown Mode
(see page 17)

HVC0001/HVC0002
5
ENGLISH
‹Cut power at the main electrical panel to avoid electric shock.
›Remove the existing switch if applicable.
fiInstall the bath fan controller.
flApply power at the circuit breaker.
4-wire installation
120
VAC
black
white
black
white black (LINE)
black (LOAD)
green (GND)
For installation in wet locations, protect the circuit
with a ground fault circuit interrupter (GFCI).

HVC0001/HVC0002
7
ENGLISH
Set the time and date
Set Hour Set Minutes
Set Year Set Month Set Day
Select 24H or 12H
The time flashes on the screen when it is
not yet set or after a power outage of
more than 4 hours. To set the clock,
press the main button for 3 seconds to
display the setup menu and proceed as
shown.
Press the main button for 3 seconds at
any time (or do not press any button for
60 seconds) to save any changes you
have made and exit the setup menu.

HVC0001/HVC0002
9
ENGLISH
When Automatic Daylight Savings Time changeover is enabled (DST On), the controller automatically
switches to daylight savings time (summer time) at 2:00 am on the second Sunday of March and back to
standard time (winter time) at 2:00 am on the first Sunday of November. This function is enabled by
default.
Set the Automatic Daylight Savings Time Changeover
Set Daylight
Saving Time
(2 times) (2 times)
To set the Automatic
Daylight Savings Time
Changeover, press the
main button for 3
seconds to display the
setup menu and
proceed as shown:
Press the main but-
ton for 3 seconds at
any time (or do not
press any button for
60 seconds) to save
any changes you
have made and exit
the setup menu.

HVC0001/HVC0002
11
ENGLISH
To place the controller in Ventilation Mode, proceed as shown:
Temporary override
Press the main button to temporarily turn the fan On or Off. For example, if you press the
main button to turn the fan On during the idle period, the fan will remain On until the
beginning of the next idle period or until you press the main button again.
Ventilation Mode (cont’d)
Select
Ventilation Mode
Ventilation Mode
Normal Display
(3 sec.) (3 sec.)

HVC0001/HVC0002
13
ENGLISH
To place the controller in Customized Cycle Mode, proceed as shown:
Temporary override
Press the main button to temporarily turn the fan On or Off. For example, if you press the
main button to turn the fan On during the idle period, the fan will remain On until the
beginning of the next idle period or until you press the main button again.
Customized Cycle Mode (cont’d)
Select Customized
Cycle Mode
Customized Cycle Mode
Normal Display
(3 sec.) (3 sec.)

HVC0001/HVC0002
15
ENGLISH
To place the controller in Daily On/Off Mode, proceed as shown:
Temporary override
Press the main button to temporarily turn the fan On or Off. For example, if you press the
main button to turn the fan On, it will remain On until the programmed Off time or until you
press the main button again.
Daily On/Off Mode (cont’d)
Select Daily
On/Off Mode
Daily On/Off Mode
Normal Display
(3 sec.) (3 sec.)

HVC0001/HVC0002
17
ENGLISH
Place the controller in Countdown Mode to run the fan for 10-60 minutes. The fan turns On when the
controller is in this mode. At the end of the countdown time, the controller returns to its programmed mode
and the fan turns Off. (NOTE: The fan might stay On if the controller has been set to turn the fan On at
that given time in the programmed mode.)
You can cancel the Countdown Mode and return to the programmed mode at any time by pressing the
main button.
To place the controller in Countdown Mode, proceed as shown:
Countdown Mode
After
5 sec.
Set Countdown
Time (minutes) *
Countdown Mode
is activated
At end of Countdown Mode
Normal Display _+
* Press the left or right button once
to use the same countdown time
as the one used the last time.
Press the left (-) or right (+) button
more than once to decrease or
increase the countdown time (in
increments of 5 minutes).

Owner’s Guide 400-305-000-EFS
18
ENGLISH
HVC0001:white
HVC0002: biscuit
Voltage: 120 VAC - 15%, + 10%
Frequency: 60 Hz ± 5%
Minimum Load: 0.1 A (12 W)
Maximum Load: 2.5 A (300 W)
Minimum Power Factor:0.60
Operating Temperature Range: -15°C to 50°C (5°F to 122°F)
Storage Temperature Range: -40°C to 60°C (-40°F to 140°F)
Product Specifications