Honeywell PW-6000 Operator's manual

August 2013 © 2013 Honeywell. All rights reserved. 800-00005V3
PW-6000
(PW6K1IC)
Intelligent Controller
and System
Installation and Configuration Guide

August 2013 © 2013 Honeywell. All rights reserved. 800-00005V3
Copyright© 2013 Honeywell. All rights reserved.
All product and brand names are the service marks, trademarks, registered trademarks, or registered
service marks of their respective owners. Printed in the United States of America. Honeywell reserves the
right to change any information in this document at any time without prior notice.
Pro-Watch®is a trademark of Honeywell, Inc.
Ordering Information
Please contact your local Honeywell representative or visit us on the web at
www.honeywellintegrated.com for information about ordering.
Feedback
Honeywell appreciates your comments about this manual. Please visit us on the web at www.honey-
wellintegrated.com to post your comments.

PW-6000 (PW6K1IC) Installation and Configuration Guide, Document 800-00005V3 1
CONTENTS
Chapter 1 PW-6000 Installation
1 Notices ................................................................................................. 2
1.1 Warnings and Cautions ................................................................... 2
1.2 UL/ULC Warnings ........................................................................... 3
1.3 Damage During Shipment ............................................................... 4
1.4 Electro Static Discharge................................................................... 4
1.5 Disclaimer – Product Liability; Mutual Indemnification ........... 5
1.6 Unpacking Procedure ...................................................................... 5
1.7 Shipping Instructions
....................................................................... 6
1.8 Limited Warranty
............................................................................. 6
1.9 Confidentiality
.................................................................................. 7
1.10 Compliance ...................................................................................... 7
1.11 Recommended testing and maintenance. .................................... 8
2 Product Overview...................................................................... 8
2.1 PW-6000 and PW-5000 ................................................................... 9
2.2 Port Settings....................................................................................... 9
2.3 Other.................................................................................................... 9
3 Setting Up the PW-6000 Hardware......................... 11
3.1 Setting the Jumpers........................................................................ 11
3.2 Setting the DIP Switches .............................................................. 12
3.3 Technical Specifications ............................................................... 14
3.4 Status LEDs ................................................................................... 15
3.5 Supplying Power to the PW-6000 Interface .............................. 16
3.6 Communications Wiring............................................................... 17
3.7 Cabinet Tamper and Power Failure Input Wiring..................... 17
3.8 Memory and Real Time Clock Backup Battery ........................ 18
4 System Configuration via Web Interface......... 18
4.1 Connecting to ACDSM for the First Time................................. 18
4.2 Login Page ...................................................................................... 19
4.3 Home Page ...................................................................................... 19
4.4 Network Settings............................................................................ 20
4.5 Host Port.......................................................................................... 21
4.6 Device Information........................................................................ 25
4.7 User Configuration ........................................................................ 26

2www.honeywell.com
4.8 Restore Default Screen.................................................................. 27
4.9 Apply Setting Screen..................................................................... 28
4.10 Log Out.......................................................................................... 28
Appendix A PW-6000 Web Server and
Pro-Watch Channels
Appendix B SNET Reader Settings

PW-6000 (PW6K1IC) Installation and Configuration Guide, Document 800-00005V3 1
In this chapter...
Notices 2
Product Overview 8
Setting Up the PW-6000 Hardware 11
System Configuration via Web Interface 18
1
PW-6000 Installation

2www.honeywell.com
PW-6000 Installation
Notices
1 Notices
Wiring methods shall be in accordance with the National Electrical Code
(ANSI/NFPA70), Canadian Electrical Code, Part I (CSA C22.1) Safety Standard for
Electrical Installations, local codes, and the authorities having jurisdiction.
Caution: Disconnect power before servicing.
ATTENTION: Débranchez l'alimentation électrique avant l'entretien.
1.1 Warnings and Cautions
Note: See the Remote Enclosure Installation Manuals PW5K2ENC1/PW5K2ENC2 or
PW5K1ENC3 (not evaluated by UL) for installation instructions.
1.1.1 Before Installation
Warning: Before installation, TURN OFF the external circuit breaker which supplies
power to the system.
AVERTISSEMENT: Avant de procéder à l'installation, DESENCLENCHER le
disjoncteur via lequel le système est alimenté.
Before connecting the device to the power supply, verify that the output voltage is
within specifications of the power supply (see 'Technical Specifications' on page 14).
Do not apply power to the system until after the installation has been completed.
Personal injury or death can occur, and the equipment can be damaged beyond repair,
if this precaution is not observed.
1.1.2 Fire Safety and Liability Notice (Not Evaluated by UL for fire,
life safety, or burglary application)
Warning: Never connect card readers to any critical entry, exit door, barrier, elevator or
gate without providing an alternative exit in accordance with all the fire and life
safety codes pertinent to the installation.
AVERTISSEMENT: Ne jamais connecter de lecteur de carte en un point critique
(porte de sortie, barrière, ascenseur ou portillon) sans proposer une autre sortie, ce afin
de respecter la règlementation en vigueur en matière d'incendie et de protection des
vies humaines, afférente à l'installation.
These fire and safety codes vary from city to city and you must get approval from
local fire officials whenever using an electronic product to control a door or other
barrier. Use of egress buttons, for example, may be illegal in some cities. In most
applications, single action exit without prior knowledge of what to do is a life safety
requirement. Always make certain that any required approvals are obtained in writing.
DO NOT ACCEPT VERBAL APPROVALS SINCE THEY ARE NOT VALID.
Honeywell Integrated Security never recommends using the PW-6000 or related
products for use as a primary warning or monitoring system. Primary warning or
monitoring systems should always meet the local fire and safety code requirements.

PW-6000 Installation
Notices
PW-6000 (PW6K1IC) Installation and Configuration Guide, Document 800-00005V3 3
Failure to test a system regularly could make the installer liable for damages to the end
user if a problem occurs.
1.1.3 Earth Grounding
Warning: The earth ground is connected at the factory and should not be removed.
AVERTISSEMENT: La prise de terre est reliée à l'usine et ne doit pas être retirée
1.1.4 Use Suppressors
Warning: Use suppressors on all door strikes. Use S-4 suppressors for installation.
Honeywell Integrated Security, Inc. recommends only DC strikes.
AVERTISSEMENT: Employer des suppresseurs de surtensions transitoires (S-4) sur
toutes les gâches de porte. Honeywell Integrated Security recommande l'utilisation
exclusive de gâches électriques à courant continu.
1.2 UL/ULC Warnings
The following applies to installations that require UL or ULC compliance:
Only UL/ULC Listed readers with standard Wiegand data output communication
format (protocol) have been evaluated for use with this system.
This product is intended to be installed indoors, within the protected premises.
Access Control System, Model PW6000, and Controller, Model PW6K1IC meet the
requirements for CAN/ULC-S319-05 Equipment Class 1. This product's compliance
to ULC-S319, Electronic Access Control Systems, will be considered invalidated
through the use of any add-on, expansion, memory or other module manufactured or
supplied by the manufacturer or manufacturer's representative, unless specifically
evaluated by ULC.
All unused conduit holes must be properly plated or incorporate a Listed plug to fill
any voids.
All interconnecting devices must be UL/ULC Listed.
Refer to the following Installation manuals for installation, connection, programming,
and operation instructions of the following sub-assemblies:
Assembly Number Installation Manual Part Number
PW6K1IC 800-00005V3
PW6K1R2 800-01951V4
PW6K1IN 800-01952V1
PW6KOUT 800-01953V1

4www.honeywell.com
PW-6000 Installation
Notices
Note: Not Evaluated by UL for fire, life safety, or burglary applications.
The earth ground is connected at the factory and should not be removed.
Do Not Connect To A Receptacle Controlled By A Switch.
Replacement 3 volt lithium coin cell must be one of the following:
Rayovac: BR2325 or BR2335-B
All interconnecting wire must be UL/ULC Listed, rated and suitable for the use.
The battery leads and primary AC main power wiring is non-power limited. This
wiring must be separated from all other wiring by at least 0.25" and cannot be
installed in the same conduit as any other power limited wiring.
The system must be configured to activate an alarm or trouble signal. Failure to do so
will not allow the access function to operate in the event of a tamper.
1.3 Damage During Shipment
Caution: IF ANY DAMAGE TO THE SHIPMENT IS NOTICED, A CLAIM MUST
BE FILED WITH THE COMMERCIAL CARRIER RESPONSIBLE FOR THE
DAMAGE.
ATTENTION: SI L'EQUIPEMENT A SUBI DES DOMMAGES LORS DE SON
TRANSPORT, ADRESSER UNE RECLAMATION AU TRANSPORTEUR
RESPONSABLE.
1.4 Electro Static Discharge
Caution: Electro-static discharge (ESD) can damage CMOS integrated circuits and
modules.
To prevent damage always follow these procedures:
• Use static shield packaging and containers to transport all electronic
components, including completed reader assemblies.
• Handle all ESD sensitive components at an approved static-controlled
workstation. These workstations consist of a desk mat, floor mat and an ESD
wrist strap. Workstations are available from various vendors.
ATTENTION: Des décharges électrostatiques peuvent endommager les modules et
circuits intégrés CMOS.
PW5K2ENC1 and PW5K2ENC2 800-06952
PW5K1ENC3 800-06955V1
PW5K2ENC5 800-08421
PW6K2E2PS 800-08279V3
Assembly Number Installation Manual Part Number

PW-6000 Installation
Notices
PW-6000 (PW6K1IC) Installation and Configuration Guide, Document 800-00005V3 5
Note: This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment.This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
installation and user guides, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his own expense.
Note: This document and the data in it shall not be duplicated, used or disclosed to
others for procurement or manufacturing, except as authorized by and with the written
permission of Honeywell Integrated Security, Inc.The information contained in this
document or in the product itself is the exclusive property and trade secrets of
Honeywell Integrated Security, Inc. Copyright laws of the United States protect all
information in this document or in the software product itself.
Note: Any use of this product is subject to the terms and acceptance of the Honeywell
Integrated Security, Inc. Software Agreement. Please request a copy from Honeywell
Integrated Security, Inc. (http://www.honeywellintegrated.com/index.html), and
review the agreement carefully.
1.5 Disclaimer – Product Liability; Mutual Indemnification
If a Customer receives a claim that a Product or any component thereof has caused
personal injury or damage to the property of others, Customer shall immediately
notify Honeywell Integrated Security in writing of all such claims. Honeywell
Integrated Security shall defend or settle such claims and shall indemnify and hold
Customer harmless for any costs or damages including reasonable attorneys’ fees
which Customer may be required to pay as a result of the defective Product or the
negligence of Honeywell Integrated Security, its agents, or its employees.
Customer shall hold harmless and indemnify Honeywell Integrated Security from and
against all claims, demands, losses and liability arising out of damage to property or
injury to persons occasioned by or in connection with the acts or omissions of
Customer and its agents and employees, and from and against all claims, demands,
losses and liability for costs of fees, including reasonable attorneys’ fees, in
connection therewith.
1.6 Unpacking Procedure
Caution: If any damage to the shipment is noticed before unpacking, a claim must be
filed with the commercial carrier.
ATTENTION: SI L'EQUIPEMENT A SUBI DES DOMMAGES LORS DE SON
TRANSPORT, ADRESSER UNE RECLAMATION AU TRANSPORTEUR
RESPONSABLE.
All containers should be opened and unpacked carefully in order to prevent damage to
the contents.
Follow these steps to unpack equipment in preparation for installation:

6www.honeywell.com
PW-6000 Installation
Notices
1. Open the container and remove the unit(s) and all packing material. Retain the
container and all the packing materials. They may be used again for
reshipment of the equipment, if needed.
2. Inspect the contents to see if anything is missing. If you notice any missing
items, contact the order entry department at 1-800-323-4576 Option-1.
3. Visually check the contents. If you see any damage, do the following:
a. If shipping has caused damage to the unit, a claim must be filed with the
commercial carrier.
b. If any other defect is apparent, call for a return authorization.
1.7 Shipping Instructions
To ship equipment back to Honeywell Integrated Security, contact the customer
service department at 1-800-323-4576 before returning the equipment. When you call,
please have available:
• A description of the problem or the reason you are returning the equipment.
• Your original purchase order number, invoice number and if the unit is still
under warranty.
• A new purchase order number if the unit is not under warranty
From the customer service department, obtain the Return Authorization Number
(RMA).
Show the RMA number on all packages shipped. Packages, which are not marked
with an RMA number will be refused at the factory and returned to you COD.
Carefully pack the equipment for shipment. Use the original packing material
whenever possible
1.8 Limited Warranty
All Products sold or licensed by Honeywell Integrated Security include a warranty
registration card which must be completed and returned to Honeywell Integrated
Security by or on behalf of the end user for Honeywell Integrated Security to provide
warranty service, repair, credit or exchange. All warranty work shall be handled
through Customer which shall notify Honeywell Integrated Security and apply for a
Return Merchandise Authorization (RMA) number prior to returning any Product for
service, repair, credit or exchange. Honeywell Integrated Security warrants that its
Products shall be free from defects in materials and workmanship for a period of two
years from the date of shipment of the Product to Customer. The warranty on
Terminals, Printers, Communications Products and Upgrade kits is 90 days from the
date of shipment. Satisfaction of this warranty shall be limited to repair or replacement
of Products which are defective or defective under normal use. Honeywell Integrated
Security’s warranty shall not extend to any Product which, upon examination, is
determined to be defective as a result of misuse, improper storage, incorrect
installation, operation or maintenance, alteration, modification, accident or unusual
deterioration of the Product due to physical environments in excess of the limits set
forth in Product manuals. THERE ARE NO WARRANTIES WHICH EXTEND

PW-6000 Installation
Notices
PW-6000 (PW6K1IC) Installation and Configuration Guide, Document 800-00005V3 7
BEYOND THIS PROVISION. THIS WARRANTY IS IN LIEU OF ALL OTHER
WARRANTIES WHETHER EXPRESS, IMPLIED OR STATUTORY, INCLUDING
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY
PARTICULAR PURPOSE. NO REPRESENTATION OR WARRANTY OF THE
DISTRIBUTOR SHALL EXTEND THE LIABILITY OR RESPONSIBILITY OF
THE MANUFACTURER BEYOND THE TERMS OF THIS PROVISION. IN NO
EVENT SHALL HONEYWELL INTEGRATED SECURITY BE LIABLE FOR
ANY RE-PROCUREMENT COSTS, LOSS OF PROFITS, LOSS OF USE,
INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES TO ANY PERSON
RESULTING FROM THE USE OF HONEYWELL INTEGRATED SECURITY’S
PRODUCTS.
1.9 Confidentiality
All software, drawings, diagrams, specifications, catalogs, literature, manuals and
other materials furnished by Honeywell Integrated Security relating to the design, use
and service of the Products shall remain confidential and shall constitute the
proprietary rights of Honeywell Integrated Security and Customer agrees to treat such
information as confidential. Customer shall acquire no rights in the design of the
Products or the related materials except to use such information solely for the purpose
of and only during the time it sells the Products.
Customer shall not copy the design of any of the Products or use or cause to be used
any Product design or related materials for its own benefit or for the benefit of any
other party. The covenants contained in this section shall remain effective throughout
the term of this Agreement and thereafter unless specifically waived by Honeywell
Integrated Security in writing.
1.10 Compliance
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB- 003 du Canada.
To obtain applicable EU compliance Declaration of Conformities for this product,
please refer to our website,
http://www.security.honeywell.com/hsce/international/index.html.
For any additional information regarding the compliance of this product to any
EU-specific requirements, please contact:
Honeywell Security & Communications
Honeywell Security - Quality Assurance Dept., Newhouse Industrial Estate
Motherwell
Lanarkshire ML1 5SB
Scotland
United Kingdom
Tel: [phone]
Email: [email protected]

8www.honeywell.com
PW-6000 Installation
Product Overview
1.11 Recommended testing and maintenance.
Perform the following on a semi-annual basis. Disconnect power from the enclosure,
open the enclosure door and inspect the system including the DC battery. Replace the
DC battery if it shows any sign of corrosion or leakage or if the battery is 2 years old
or older. Oil the lock cylinder. Close the panel and re-apply power.
2 Product Overview
The Intelligent Controller is the heart of the PW-6000 and provides the real time
processing for the connected I/O interfaces.
The PW-6000 is designed to operate without the need for a PC. It can be connected to
a Pro-Watch host computer using direct serial communication, dial-up modem, or
TCP/IP network connection. The PW-6000 holds the database for the subsystem
configuration and card holders, and the event log buffer, which is in battery-backed
memory.
Notes:
• Please refer to the Pro-Watch Software Suite Guide for details on using the
Pro-Watch interface.
• The optional Lantronix Cobox-Micro interface daughter board and dial-up
modem have not been tested to comply with UL 294 and cannot be used on UL
294 approved installations.

PW-6000 Installation
Product Overview
PW-6000 (PW6K1IC) Installation and Configuration Guide, Document 800-00005V3 9
2.1 PW-6000 and PW-5000
• The PW-6000 controller configuration and operation is similar to the PW-5000
controller; both use the Pro-Watch at the front end.
Note: The PW6K1IC controller is compatible with the following Honeywell modules:
PW6K1R2, PW6K1IN, and PW6K1OUT. The PW6K1IC is also compatible with the
following PW5K assemblies but they have not been evaluated by UL for S-319:
PW5K1R1, PW5K1R2, PW5K1IN, PW5K1OUT.
2.2 Port Settings
•Port 0 provides the host-embedded Ethernet interface.
•Port 1 is for RS-232 or RS-485 2-wire serial interface connections. An
optional Lantronix CoBox-Micro interface daughter board
(10Base-T/100Base-TX) is also supported on Port 1.
•Ports 2 and 3are for RS-485 2-wire downstream support for connecting 32
I/O devices. Note that the I/O communications must be mapped differently in
Pro-Watch, according to the following table:
See Table 1 'PW-6000 Jumper Settings' on page 11 for more information on how to
configure the port settings.
2.3 Other
• An on-board real time clock maintains the date and time, taking into account
leap year and accounting for global time zones and daylight savings time
changes.
• The database for the system configuration and card holders are stored in
FLASH memory.
• The event log buffer is stored in battery-backed memory.
• Configuration data and event/status reports are communicated to the host via
on-board 10-BaseT/100Base-TX Ethernet port or Port 1.
• Transactions are stored in 1 MB of battery-backed SRAM. The maximum
number of transactions stored while the host is offline is 50,000.
• Cards are stored in Flash memory and read into DRAM when the board is
powered up. The amount of storage available for cards and biometric records is
15 MB. The maximum number of cards depends on the card record database
configuration, but the number is approximately 300,000. This maximum is
dependent on how the card is configured with more space per card used with
longer card number, more clearance codes, and so on.
PW-6000 Port Pro-Watch Port
24
36

10 www.honeywell.com
PW-6000 Installation
Product Overview
Figure 1: PW-6000 Connections, LEDs, and DIP Switches

PW-6000 Installation
Setting Up the PW-6000 Hardware
PW-6000 (PW6K1IC) Installation and Configuration Guide, Document 800-00005V3 11
3 Setting Up the PW-6000 Hardware
The PW-6000 processor is configured with 12 jumpers and a set of 4 DIP switches.
These jumpers/switches set up the port interface, end of line termination, and
operating mode configuration. Refer to the tables below to set the jumpers as required.
3.1 Setting the Jumpers
Table 1 PW-6000 Jumper Settings
Jumpers Set At Description
J1 N/A 10Base-T/100Base-TX Ethernet Connection (Port 0)
J2 N/A Factory Use Only
J3 OFF Port 2 RS-485 EOL Terminator is OFF
ON Port 2 RS-485 EOL Terminator is ON
J4 OFF Port 3 RS-485 EOL Terminator is OFF
ON Port 3 RS-485 EOL Terminator is ON
J5 OFF Port 1 RS-485 EOL Terminator is OFF
ON Port 1 RS-485 EOL Terminator is ON
J6 N/A Factory Use Only
J7 N/A COBOX-MICRO Ethernet Module Connection (Port 1)
J8, J9, J10 232 Port 1 is RS-232
485 Port 1 is RS-485
J11 N/A Factory Use Only
J12 N/A Factory Use Only

12 www.honeywell.com
PW-6000 Installation
Setting Up the PW-6000 Hardware
3.2 Setting the DIP Switches
Dual In-line Package (DIP) switches are read when the system powers up, except
where noted otherwise. The following table shows the setting options.
Table 2 PW-6000 DIP Switch Settings
S1 S2 S3 S4 Selection
OFF OFF OFF OFF Normal Operating Mode.
ON OFF OFF OFF When DIP switch 1 is ON, Port 0
communicates with the web browser.
Port 1 is used for RS-232/485
communications. After the panel
initialization, enable the default user
name (admin) and password (password).
The user name and password are read
dynamically; you do not need to reboot
the panel.
OFF ON OFF OFF Use the factory default communication
parameters.
ON ON OFF OFF Unless the network administrator
reserves an IP address for the panel
(based on the controller board’s Media
Access Control (MAC) address), the
PW-6000 uses Dynamic Host
Configuration Protocol (DHCP) to
obtain an IP address from the network
DHCP server.
When power is applied with the
switches in this position, there is a ten
second window (when LEDs 1and 2
flash alternately with LEDs 3 and 4),
during which memory is cleared if
switch 1 or switch 2 is changed to OFF.
When switch 1 or 2 is changed to OFF,
only LED 2 flashes and memory begins
to be cleared. This period of clearing
lasts several minutes. When the memory
has been cleared, the LED pattern
changes to the flashing of LEDs 1 and 4.
The panel then reboots by itself. All data
in memory is erased except the serial
number, MAC address, hardware
revision, and OEM code.

PW-6000 Installation
Setting Up the PW-6000 Hardware
PW-6000 (PW6K1IC) Installation and Configuration Guide, Document 800-00005V3 13
The PW-6000 DIP switches need to be set twice:
1. Configure the S4-S3-S2-S1 DIP switches to off-off-on-off to set the default
TCP/IP address to 192.168.0.251.
2. Apply power to the panel to set the IP address.
3. Change the S4-S3-S2-S1 combination to off-off-off-on.(DIP switch 1 is “read
on the fly”). This sets the login to the default user ID (“admin”) and password
(“password”) for Ethernet communications.
4. Create users. See 'User Configuration' on page 26 for instructions.
5. Set the S4-S3-S2-S1 combination to off-off-off-off.
6. Configure the host port for TCP/IP and/or Serial communications. See 'Host
Port' on page 21 for instructions. This will enable both TCP/IP and serial
hardware networking when you log in again.

14 www.honeywell.com
PW-6000 Installation
Setting Up the PW-6000 Hardware
3.3 Technical Specifications
Table 3 PW-6000 Technical Specifications
Category Description
WARNING: PW-6000 is manufactured for use in
low-voltage, Class 2 power-limited circuits only.
AVERTISSEMENT: Le PW-6000 est conçu pour un usage en
basse tension, des circuits de classe 2 puissance limitée.
Primary Power 12Vdc ± 10%, 300mA maximum.
12Vdc @ 240mA (325mA with CoBox-Micro) nominal (Not
Evaluated by UL/ULC).
Memory and
Clock Backup
3Volts Lithium, type BR2325, BR2330, CR2330.
Ports Port 0 10Base-T/100Base-TX Ethernet.
Port 1 RS-232 or 2-wire RS-485: 9,600 to 115,200
bps, async. An optional Lantronix
CoBox-Micro interface daughter board is
supported (10Base-T/100Base-TX -- Not
Evaluated by UL/ULC).
Port 2 & 3 2-wire RS-485: 2,400 to 38,400 bps, async.
Inputs 2 non-supervised, dedicated for cabinet tamper and power fault
monitoring.
Cable requirements Power: 1 twisted pair, 18 AWG.
RS-485: 24AWG, 4,000ft (1,200m) maximum, twisted
pair with shield. 120 ohm.
RS-232: 24AWG, 25ft (7.6m) maximum.
Ethernet: Cat 5.
Input: 1 twisted pair, 30 ohms maximum.
Environmental Temperature: 0 to 49°C, operating
-55 to +85°C, storage
Humidity: 0 to 85% RHNC
Mechanical Dimensions: 5.5 in. (137.7mm) W x 9 in. (228.6.4mm) L
x .75 in. (19.05mm) H
Weight: 7.1 oz. (201 gm) nominal
Lantronix NIC
support
Standoff size Diameter 0.125 inch x 0.4375 inch long
Richco Plastics part number LMSP-7-01, 3 pieces (not
supplied)
Specifications subject to change without notice.

PW-6000 Installation
Setting Up the PW-6000 Hardware
PW-6000 (PW6K1IC) Installation and Configuration Guide, Document 800-00005V3 15
Caution: Locate the power source as close to this board as possible. Connect power
with minimum of 18AWG wires.
ATTENTION: Placez la source d'alimentation au plus proche de la carte
électronique. Connectez l'alimentation avec des fils d'un minimum de 18 AWG.
Note: POLARITY for 12 VDC power is important. Make sure the +12 VDC is
connected to the terminal labeled +12V and the return is connected to the terminal
labeled GND.
3.4 Status LEDs
The PW-6000 uses six on-board LEDs to provide status information during its
initialization sequence and normal run-time operation.
3.4.1 Initialization
Table 4 PW-6000 Status LED Combinations During Initialization
LED 1 LED 2 LED 3 LED 4 LED 5 LED 6 Description
ON OFF OFF OFF OFF OFF Basic processor initialization
ON ON OFF OFF OFF OFF Internal SRAM test
ON OFF ON OFF OFF OFF External SDRAM, First Chip
ON ON ON OFF OFF OFF External FLASH Test
ON OFF OFF ON OFF OFF External SDRAM, Second
ON ON OFF ON OFF OFF External SRAM Test
ON OFF ON ON OFF OFF External EEPROM Test
ON ON ON ON OFF OFF External RTC Test
ON OFF OFF OFF ON OFF Backup Battery and Reset
ON ON OFF OFF ON OFF UART Test
ON OFF ON OFF ON OFF Ethernet Interface, MII
OFF ON X X X X Final processor Initialization

16 www.honeywell.com
PW-6000 Installation
Setting Up the PW-6000 Hardware
3.4.2 Run TimeSupplying Power to the PW-6000 Interface
3.5 Supplying Power to the PW-6000 Interface
The processor accepts 12Vdc for power. Locate power source as close to the unit as
possible and connect it with minimum of 18AWG wires.
Caution: Observe POLARITY on 12 VDC.
ATTENTION: Observez la polarité du 12 VCC
Figure 2: PW-6000 Power Terminals
Table 5 PW-6000 Status LED Combinations During Run Time
LED Description
1 Off-Line / On-Line and Battery Status
Off-Line = 20% On, ON-Line = 80% On
Double Flash means the Battery is Low
2 Primary Host Communication Activity (Ethernet or Port 1)
3 Port 2 Communication Activity
4 Port 3 Communication Activity
5 ON = Writing to Flash Memory. Do NOT cut off power when this LED is ON.
6TBD
SPD On-Board Ethernet Speed. OFF = 10MBS. ON = 100MBS.
ACT OFF = No On-Board Ethernet Activity. ON = On-Board Ethernet Activity
(YELLOW LED).
LNK OFF = ON Link. ON = Good Link (GREEN LED).
PORT 3
+12V
GND
-
+
TB1
GND
TR-
TR+
12Vdc ±10%