Honeywell HercuLine 2000 Series User manual

62-86-25-14 Quick Start Guide for Herculine 2000 Series Actuators
February 2007
Page 1 of 10
Honeywell’s HercuLine®2000 series actuators are available in four versions: HercuLine®2000, HercuLine®2001,
HercuLine®2002, and HercuLine®2003. All are low torque, precision electric rotary actuators. This guide provides
you with mechanical and electrical installation information required to mount and connect the HercuLine®2000 Series
Actuator to your specific application. Installation considerations, electrical and safety precautions should be observed.
An external disconnect switch must be installed to break all current carrying
conductors connected to the actuator. Turn off power before working on
conductors. Failure to observe this precaution may result in serious personal injury.
Refer to the Model Selection Guide on Pages 9 and 10 to determine which features and functions are on your model.
For additional information, refer to HercuLine Series 2000 Installation/Operation Manual # 62-86-25-10
Overview
The procedures to install the HercuLine®2000 Series actuator and place it in service require that you:
1. Select a suitable location for installation.
2. Mount the actuator securely.
3. Install mechanical connections or linkage between control arm and final control element. Use HAL software
application to aid in mechanical installation.
4. Make all electrical connections for actuator according to local and national electrical codes.
5. Power up actuator.
6. Enter, verify and adjust set up parameters for proper operation.
7. Check the operation of the Actuator
1. Installation Considerations
Mount the actuator in a location where it will be easily accessible for maintenance and for manual operation by means
of the hand wheel. The exact location must be determined in accordance with the linkage used.
2. Actuator Mounting
Firmly bolt the actuator to a mounting surface that will not distort when subjected to the torque stresses generated by
the actuator. The output shaft of the actuator should be parallel to the output shaft of the driven device. The output
shaft crank arm is fully adjustable through 360°.
3. Linkage Set-up
Many applications require the use of a linkage assembly and often the final control element does not have a linear
torque curve. The actuator linkage can be set up to achieve an optimal delivered torque distribution for specific
applications. To assist with linkage design, Honeywell offers a linkage analysis software application (HAL). The
software can be ordered as P/N 51197910-001.
Constant Torque Linkage (typical)
A constant torque linkage is employed when it is desired to provide a linear torque profile throughout the full range of
final control element travel. In this situation, the actuator and driven crank arms will be set-up proportionally with
respect to each other.
Vertical
Centerline
45° 45°
Vertical
Centerline
45° 45°
Start Stop Close Open
Drive Unit
Crank Arm Damper Crank Arm
Linkage
Horizontal Offset
a/n23199
Figure 1 Constant Torque Linkage

62-86-25-14 Quick Start Guide for Herculine 2000 Series Actuators
February 2007
Page 2 of 10
3. Linkage Set-up (continued)
Variable Torque Linkage
A variable torque linkage is employed when it is desired to provide a non-linear torque profile throughout the full
range of final control element travel. In this general situation, the actuator and driven crank arms will be set up to
provide a higher torque for seating or unseating the final control element.
Vertical
Centerline
5°
Vertical
Centerline
45° 45°
Close Open
Actuator
Crank Arm
Damper
Crank Arm
Linkage
Horizontal Offset
a/n 23200
Figure 2 Variable Torque Linkage
4. Electrical Connections
The actuator terminal connections for the field wiring are located behind the cover on the actuator case. Power and field
wiring is brought into the actuator through two access holes located on the side of the actuator case.
Use both openings: one for low level wiring (control signal) and the other for high
level wiring (120Vac).
Do not run both the High Level and Low Level wiring through the same
opening.
Recommended Minimum Wire Size
In general, copper wire used unless locally applicable codes dictate otherwise.
Earth ground wire to common power supply -14AWG
Earth ground wire to single actuator. 120/240 Vac line leads. +24 V and common signal leads. Common signal leads,
relays, and aux switches – 18AWG
HercuLine®2000 Wiring Connections
158 ohm 158 ohm Install resistors to convert 1000 ohm
potentiometer to 135 ohms
1
1
REQUIRED ONLY IF AUTO/MANUAL
SWITCH IS PRESENT
158 ohm 158 ohm Install resistors to convert 1000 ohm
potentiometer to 135 ohms
11
11
REQUIRED ONLY IF AUTO/MANUAL
SWITCH IS PRESENT
Figure 3 HercuLine®2000 connections
Connection Terminal Description
Hot 1 Hot wire for 120/240VAC main supply.
NOTE:Use only if Auto/Manual switch is present.
Neutral 2 Neutral wire for 120/240VAC main supply
Auto/Manual
Switch Contact 3
4
Switch contact to indicate setting of actuator AUTO/MANUAL
switch.
Switch is closed when actuator is “NOT-IN-AUTO”

62-86-25-14 Quick Start Guide for Herculine 2000 Series Actuators
February 2007
Page 3 of 10
CW from
Controller 5 CW Motor Drive
CCW from
Controller 6 CCW Motor Drive
Potentiometer #1 7
8
9
Clockwise-End
Slidewire feedback
Counterclockwise-End
Potentiometer #2 10
11
12
Clockwise-End
Slidewire feedback
Counterclockwise-End
Protective Ground Ground wire connection for main supply
HercuLine®2001/2002 Wiring Connections
Auxiliary
Connector
_
Brown
Black
Blue
+
Black Wire Not Used
HART connection using
external Turck connector
+_
HART
Communications
Connection
Auxiliary
Connector
_
Brown
Black
Blue
+
Black Wire Not Used
HART connection using
external Turck connector
Auxiliary
Connector
_
Brown
Black
Blue
+
Black Wire Not Used
HART connection using
external Turck connector
+_
HART
Communications
Connection
Figure 3 HercuLine®2001/2002 Connections
Connection Terminal Description
TB1
Hot 1 Hot wire for 120/240VAC main supply
Neutral 2 Neutral wire for 120/240VAC main supply
Protective Ground 3 Ground wire connection for main supply
Auto/Manual Switch
Contact 4 5 Switch contact to indicate setting of actuator AUTO/MANUAL switch.
Switch is closed when actuator is “NOT-IN-AUTO”
6
TB3
4 to 20mA Output* 1 (+)
2 (-) Analog signal output
Feedback 3
Feedback signal used in conjunction with 4 to 20mA OUTPUT voltage
when using Slidewire Emulation
4 to 20mA Input 4 (+)
5 (-) Analog signal input
Modbus
Communication 6 (+) 7 (-)
8 Shield
Connection for RS485 Modbus loop wires
HART
Communications 4 (+) 5 (-) HART Communication is 4-20 mA only.
Digital Input 9 Com
10 Input Customer’s contact closure
* Optional

62-86-25-14 Quick Start Guide for Herculine 2000 Series Actuators
February 2007
Page 4 of 10
4. Electrical Connections (continued)
HercuLine®2003 Wiring Connections
Figure 5 HercuLine®2003 Wiring Connections
HercuLine®2003 Operation
The 2003 actuator is uni-directional (it does not
reverse rotation with a reversal in control action).
Figure 5 illustrates the internal wiring and the external
connections.
The smaller insert of the figure describes the limit
switch action for one complete cycle. When the two-
position controller detects a sufficient fall in
temperature in a heating application, the switch
portion between the “4” and “5” terminals will close.
The motor then rotates for 180º or until the opening
switch breaks (stops are adjustable, factory set at
180º), and stops in full open position.
A subsequent rise in temperature causes the
controller to close the switch between the “4” and “6”
terminals when the motor will start to rotate (in the
same direction) for 180º or until the closing switch
breaks.
The motor stops in the closed position and completes
one cycle.
Series 90 Control – HercuLine®2001 model only
Series 90 Controls are commonly used in building environmental systems and flame safeguard systems to provide
modulating control. The control is affected by balancing a 135 ohm potentiometer. The HercuLine 2001 provides
an emulation of this system as follows. The current output is used to excite the potentiometer in the controller. To
do this it is set permanently at 11 mA. This produces a 1.5 volt span. The wiper is then connected to the
HercuLine 2001 input, which is operating in voltage mode. The returns from both the input and the output are tied
together.
Series 90 terminals are typically color coded white, red and blue. Conventionally, red is the wiper and white and
blue are the two ends of the potentiometer. On a drop in temperature, the wiper moves toward the blue terminal.
Connections
4-20mA output
4-20mA input
1+
2-
4+
5-
White
Red
Blue
TB3
Figure 6 Series 90 connections

62-86-25-14 Quick Start Guide for Herculine 2000 Series Actuators
February 2007
Page 5 of 10
Considerations
1. This connection performs an emulation of a series 90 motor. If the controller being used is also an
emulation of a Series 90, the connections required may be different. Shown in Figure 7are the
connections found necessary to connect a T775 controller through an S443A S90 Auto/Manual Control.
If the controller has the capability to provide a 4/20 or voltage output, it is easier to use that mode. It
will require only two wires and it will allow the independent use of the 4/20 output. If help is required,
contact Honeywell.
2. Due to variations in the definition of rotation directions, it may be necessary to reverse the action of the
actuator from CCW to CW or vice versa.
GND to
HercuLine2001 (2)
W
W
W
R
R
BB
A
uto
Man
I out from
HercuLine2001
+ Signal to
HercuLine2001
T775 B 3
T775 W 1
T775 R 2
Figure 7 T775 Controller connections
3. In the T775 controller manual there are several examples of using resistances or potentiometers as
high and low limit controls. Because of the mode of emulation of Series 90, it is likely that these
connections will not work as intended. Instead, use the output or input limits which are
programmable in the HercuLine®2001.
5. Power up actuator.
Depending on which power supply selection is ordered for your actuator, wire the power input (MAIN POWER) as
described in the previous tables and figures. Wiring must conform to national and local electrical codes.

62-86-25-14 Quick Start Guide for Herculine 2000 Series Actuators
February 2007
Page 6 of 10
6. Enter, verify and adjust set up parameters for proper operation. (2001/2002 with optional display)
Pressing the SET UP key on the keypad provides access to the various set up groups and allows you to set up
operating parameters, (such as input types and alarms), set communications, and check actuator status. The Table
below lists the set up groups that are available by using the SET UP and FUNCTION keys on the keypad.
TEMP TEMPHI TEMPLO ACSTAL STARTS RL1CNT
RL2CNT RL3CNT RL4CNT REGN0 REGN9 TOTDEG
DATSAV PASSWD MANRST LD CAL LD CFG RESTRT
…
VERSON SPEED POWER ROTATE TAG MFGDAT
LREP LCAL REPTYP
CUROUT
COMM ADDRES BAUD XmtDLY DBLBYT
DIGINP EndPos
DECMAL EUNITS UNITS
LOCKID LOCK MAENAB
FAILSF RAMTST SEETST CFGTST CALTST
RTYPny Rny VAL Rny E* Rny HL RTYPny Rny VAL Rny E*
Rny HL RLYnHY n = 1,2,3 or 4 y = 1 or 2
RELAYn
IN TYP INP HI INP LO FILTYP Direct Dband FSTYPH
CHAR CUSTOM X0 VAL X20 VAL
Y0 VAL
…
Y20 VAL
…
FsVALH
FSTYPL FsVALL
MAINT
DRVINF
STATUS
LOCK
DISPLA
DIGINP
COMM
INPUT
CUROUT
Setup Groups Function Prompts
TEMP TEMPHI TEMPLO ACSTAL STARTS RL1CNT
RL2CNT RL3CNT RL4CNT REGN0 REGN9 TOTDEG
DATSAV PASSWD MANRST LD CAL LD CFG RESTRT
…
TEMP TEMPHI TEMPLO ACSTAL STARTS RL1CNT
RL2CNT RL3CNT RL4CNT REGN0 REGN9 TOTDEG
DATSAV PASSWD MANRST LD CAL LD CFG RESTRT
…
VERSON SPEED POWER ROTATE TAG MFGDAT
LREP LCAL REPTYP
VERSON SPEED POWER ROTATE TAG MFGDAT
LREP LCAL REPTYP
CUROUT
COMM ADDRES BAUD XmtDLY DBLBYT
DIGINP EndPos
DECMAL EUNITS UNITS
LOCKID LOCK MAENAB
FAILSF RAMTST SEETST CFGTST CALTST
RTYPny Rny VAL Rny E* Rny HL RTYPny Rny VAL Rny E*
Rny HL RLYnHY n = 1,2,3 or 4 y = 1 or 2
RELAYn
IN TYP INP HI INP LO FILTYP Direct Dband FSTYPH
CHAR CUSTOM X0 VAL X20 VAL
Y0 VAL
…
Y20 VAL
…
FsVALH
FSTYPL FsVALL
MAINT
DRVINF
STATUS
LOCK
DISPLA
DIGINP
COMM
INPUT
CUROUT
Setup Groups Function Prompts
You can use this procedure to access the set up groups and select all parameters.
Set Up Procedure Using Display and Keypad
Step Operation Press Result
1 Enter Set Up
Mode SET UP
Upper Display = SET UP-Lets you know you are in the set up mode and a set up group
title is being displayed in the lower display.
Lower Display = INPUT-This is the first set up group you see when you press SET UP.
2 Select any
Set Up
Group
SET UP Successive presses of the SET UP key will display the other set up group titles. You can
also use the or keys to scroll through the set up groups in both directions. Stop
at the set up group title that describes the group of parameters you want to configure.
Then proceed to the next step.
3 Select a
Function
Parameter
FUNCTION Upper Display - Shows the current value or selection for the function prompt in the
selected set up group.
Lower Display - Shows the first function prompt within the selected set up group.

62-86-25-14 Quick Start Guide for Herculine 2000 Series Actuators
February 2007
Page 7 of 10
Step Operation Press Result
4 Select other
function
parameters
FUNCTION Successive presses of the FUNCTION key will sequentially display the other function
prompts of the selected set up group.
Stop at the function prompt that you want to change, and then proceed to the next step.
5 Change the
Value or
Selection
or
These keys increase or decrease the value, or display the next available selection for the
selected function prompt.
Change the value or selection to meet your needs.
NOTE: If the display flashes, you are trying to make an unacceptable entry, or the value
on the display is at its range limit. The display may also show “KEYERR” (Key error).
6 Enter Value
or Selection FUNCTION
or
SET UP
This key selects another function prompt.
This key selects another set up group.
NOTE: Pressing either key will cause the previously selected value or selection to be
entered into memory.
7 Exit Set Up
mode DISPLAY Exits set up mode and returns actuator to the same state it was in immediately preceding entry into the set up mode. Any changes you have made are stored in memory.
If you do not press any keys for 30 seconds, the display times out and reverts to the
mode and display shown prior to entering the set up mode.
Record your selections on the Configuration Record Sheet .
Configuration Record Sheet
Group
Prompt Function Prompt Value or Selection Factory Setting
INPUT IN TYP From MSG
INP HI 100
INP LO 0.0
FILTYP LPAS
LPFILT 0.5
DIRECT CCW
DBAND 0.5
FSTYPH UP
FSVALH 100
FSTYPL DOWN
FSFVALL 0
CHAR LINR
CUSTOM EQUL
X1 VAL 5
X2 VAL 10
X3 VAL 15
X4 VAL 20
X5 VAL 25
X6 VAL 30
X7 VAL 35
X8 VAL 40
X9 VAL 45
X10 VAL 50
X11 VAL 55
X12 VAL 60
X12 VAL 65
Group
Prompt Function Prompt Value or Selection Factory Setting
INPUT
(CONT) X14 VAL 70
X15 VAL 75
X16 VAL 80
X17 VAL 85
X18 VAL 90
X19 VAL 95
X20 VAL 100
Y1 VAL 5
Y2 VAL 10
Y3 VAL 15
Y4 VAL 20
Y5 VAL 25
Y6 VAL 30
Y7 VAL 35
Y8 VAL 40
Y9 VAL 45
Y10 VAL 50
Y11 VAL 55
Y12 VAL 60
Y13 VAL 65
Y14 VAL 70
Y15 VAL 75
Y16 VAL 80
Y17 VAL 85
Y18 VAL 90
Y19 VAL 95
Y20 VAL 100

62-86-25-14
February 2007
Page 8 of 10
Quick Start Guide for Herculine 2000 Series
Group
Prompt Function Prompt Value or Selection Factory Setting
RELAYn RTYP NONE
RnyE X1
RnyVAL 0.0
RnyHL LO
RLYnHY 0.0
CU OUT CUROUT NONE
Depends on
MSG
COMM COMM DIS
ADDRES 1
BAUD 19.2
XmtDLY 20ms
DBLBYT FP B
DIGINP DIGINP NONE
EndPos 0
DISPLA DECMAL 8888
EUNITS PCNT
UNITS ENGL
LOCK LOCKID 0
LOCK NONE
MAENAB ENAB
STATUS FAILSF Read Only Read Only
RAMTST Read Only Read Only
SEETST Read Only Read Only
CFGTST Read Only Read Only
CALTST Read Only Read Only
DRVINF VERSON Read Only Read Only
SPEED Read Only Read Only
POWER Read Only Read Only
ROTATE Read Only Read Only
TAG 6 alpha
characters
MFGDAT Read Only Read Only
LREP Factory Set Factory Set
LCAL Factory Set Factory Set
REPTYP Factory Set Factory Set
Group
Prompt Function Prompt Value or Selection Factory Setting
MAINT TEMP NONE
TEMPHI X1
TEMPLO 0.0
hh:mm:ss ACST Read Only
STARTS Read Only Accumulated
Motor Starts
RnCNT
n=1,2,3,or4 Read Only Relay Cycle Counts
REGNn
n= 0 to 9 Read Only Accumulated Motor Starts
TOTDEG Read Only Total Degrees of
Motor Travel
DATSAV DIS
PASSWRD Nnnn
MANRST NONE
LD CAL NONE
LD CFG DIS
RESTRT DIS
7. Start up/Operation
After the actuator is completely installed, wired, and
the preliminary adjustments made, check the
operation of the actuator and controlled device
before placing it in service. Operate the controlled
device and check its direction of travel in response
to an increase of the input signal and make sure it is
correct for the process. Actuators having the
optional auto-manual switch must have the knob set
in the AUTO position.
When power is applied to the actuator, the actuator
electronics performs a diagnostic routine on various
device components. These tests include a:
•RAM diagnostic (RAMTST),
•Check of the electrically eraseable PROM
(SEETST),
•Verification that valid parameter values are
in the actuator configuration (CFGTST),
•Verification of valid calibration values
(CALTST)
•Test of the local display and LED indicators
(all display segments and LED indicators
light simultaneously).
The optional local display shows the status of the
diagnostics as they are completed during power up.
TEST DONE is shown on the display when
diagnostics are complete and actuator should be in
AUTO mode.
If the Actuator Motor is “Hunting” (Motor does not
drive to a position and stop) the process control
loop is not tuned correctly. Refer to the Instruction
Manual for your controller on how to tune a loop.

62-86-25-14
February 2007 Quick Start Guide for Herculine 2000 Series
Model Selection Guide
Instructions
Select the desired key number. The arrow to the right marks the selection available.
Make the desired selections from Tables I thru VIII using the column below the arrow.
A dot ( ) denotes unrestricted availability.
Key Number V VI VII VIII IX
-----
_
_ -
_
_ _ _ _ _ -
_
-
_
-
_
_
KEY NUMBER - Motor Selection Availability
Basic Motor Unit (no electronics)
Basic Motor Unit plus Digital Electronics
Enhanced Performance Motor Unit with Non-contact Position Sensing
Unidirectional Motor (M640D Replacement)
TABLE I - TORQUE & SPEED SELECTION (speed per 150 degree rotation)
Torque, lb-in/(N-M)
50 / (6.0) 4.5 / 7.5 sec 4 / 6 sec
100 / (11.5) 9 / 15 sec 7 / 12 sec
200 / 22.5) 18 / 30 sec 15 / 25 sec
400 / (45.0) 36 / 60 sec 30 / 50 sec
400 / (45.0) 54 / 90 sec 45 / 75 sec
TABLE II - ROTATION
Travel 90 degrees
150 degrees
360 degrees
TABLE III - POWER SUPPLY
Single Phase 100 - 130 Vac, 60 Hz
100 - 130 Vac, 50 Hz
200 - 240 Vac, 60 Hz
200 - 240 Vac, 50 Hz
TABLE IV - ANALOG INPUT/OUTPUT SIGNALS
Input 3 Wire Drive up/down 0 _ _
0/4-20 mA, 0/1-5 Vdc, 0-10 Vdc 2 _ _
0/4-20 mA, 0/1-5 Vdc, 0-10 Vdc 3 _ _
0 to 135 ohm input (Series 90 control) 4 _ _ a
Contact Input for 2003 6 _ _
Output None _ 00
(Note 1) Dual 1000 Ohm (1000 ohms over 150 degrees) _ 15 b
(Note 1) Dual 1000 Ohm (1000 ohms over 90 degrees) _ 19 c
Slidewire Emulation _ 60
Slidewire Emulation _ 65
0/4-20mAdc (0/1-5 Vdc, 0-16 Vdc) _ 80
0/4-20mAdc (0/1-5 Vdc, 0-16 Vdc) _ 85
TABLE V - SWITCH AND RELAY OUTPUTS (2 end-of-travel limit switches are standard)
Auxiliary Outputs No Auxiliary Switches
2 Auxilliary Switches
4 Auxilliary Switches
Relay Outputs No Relays
2 Programmable Relay Outputs
2 Programmable Relay Outputs
4 Programmable Relay Outputs
_ _ _ _
50Hz (90°/150°) 60Hz (90°/150°)
Selection
2000
2001
2002
I
_
_
_
IVII
_
_
_
III
_
_
_
_
_
_
2003
050
100
200
400
600
090
150
360
0 _
2 _
4 _
126
125
246
245
_ 0
_ 2
_ 3
_ 4
Page 9 of 10

62-86-25-14
February 2007 Quick Start Guide for Herculine 2000 Series
2002 2003
TABLE VI - OPTIONS Selection
Local keypad/ No local display interface supplied (Note 2) 0_ _ _ _ _
display Integrally mounted local display/keypad interface 1_ _ _ _ _
Local Auto/ No auto/manual switch _ 0_ _ _ _
manual switch Auto/manual switch with "Out of Auto Contact" _ 1_ _ _ _
Auto/manual switch with "Out of Auto Contact" _ 2_ _ _ _
Handwheel No Handwheel _ _ 0_ _ _
Handwheel _ _ 1_ _ _
Certificates None _ _ _ 0 _ _
Certificate of Conformance _ _ _ 1_ _
Approvals UL Type 4/IP66, CSA (Note 4) _ _ _ _ 0_
CE _ _ _ _ 1_
Shipped Rotation Counter clockwise shaft rotation on increasing signal _ _ _ _ _0
Clockwise shaft rotation on increasing signal _ _ _ _ _1
TABLE VII - COMMUNICATIONS/PROTOCOL
None No communications option board or protocol 0
Modbus RTU RS485 RS-485 Modbus compliant - standard with EEU 1
HART 5 HART Communications Protocol 2
TABLE VIII - MANUALS
Standard English 0
TABLE IX - FACTORY OPTIONS
Factory Options None
Restrictions
aIV _ 00 IV _ 60, _ 80
II II
II II
ACCESSORIES
Mounting Hardware Mounting plate adapter for Barber Colman Series MP495
Mounting plate adapter for Landis & Staefa SQM53/56
Direct Couple Valve Hardware
North American Valve Retrofit Kit
Linkage Assembly Ball joint for 5/16" dia. Pushrod
Pushrod 12 in. (304,5 mm) long, 5/16 " dia.
Pushrod 18 in. (457,2 mm) long, 5/16 " dia.
Pushrod 24 in. 609,6 mm) long, 5/16 " dia.
Pushrod 48 in. (1219,2 mm) long, 5/16 " dia.
HART Turk Cable for Handheld Connection 51452352-501
Handheld Config. HercuLink
TM
PC and Palm PDA Software
(Note 3) Battery powered 232/485 converter with cable
Remote Mount Remote 4-20 mA requires 135 ohm fdbk, 120V 50/60Hz
Control Remote 4-20 mA requires 1000 ohm fdbk, 120V 50/60Hz
Remote 4-20 mA requires 135 ohm fdbk, 220V 50/60Hz
Remote 135 ohm input requires 135 ohm fdbk, 120V 50/60Hz
HercuLine 2000 V51 2.5" - 3" Valve Mounting Kit 51452354-513
HercuLine 2000 V51 4" Valve Mounting Kit 51452354-514
Notes: 1. 135 ohm available by parallelling 1K potentiometer with 158 Ohm resistor (supplied).
2. HercuLinkTM software (pn 51452354-509), RS232/485 converter (pn 51452354-510),
customer supplied PalmTM PDA running OS3.5 or higher and Palm serial cable are required
for the 2001 and 2002 actuators if no display is selected.
3. Requires PDA manufacturer's serial interface cable.
4. CSA approval is good for 75°C and a maximum relay load of 3.5 amps or 70°C with a
relay load of 5 amps.
Restriction
Letter
c
150
090
b
Table Selection
Available Only With
R7195A1056
R7195B1021
R7195A1064
51452354-508
R7195A1031
51452354-510
51452354-509
Table Selection
Not Available With
51452354-505
51452354-501
51452354-502
51452354-511
51452354-504
150
090
2000 2001
Availability
V51 Valve Kits
00
51452354-506
51452354-507
51452354-503
Page 10 of 10