Honeywell Kaliza User manual

Honeywell
Kaliza
Ceiling
Fan
User Guide
Model #51035, 51036, 51477,
51626

PACKAGE CONTENTS cs 20 au SSS SME
Please read and understand this entire manual before attempting to assemble, operate or install the product.
* Before you begin installing the fan, disconnect the power by removing fuses or turning off the circuit breakers.
* Make sure ail electrical connections comply with tacal codes. ordinances, the National Electrical Code and ANSI/NFPA
70-199. Hire an electrician or consult a do-it yourself handbook if you are unfamiliar with installing electrical wiring.
* Make sure the installation site you choose allows a minimum of 7 feet from the blades to the floor and at least 30 inches from the tip
of the blades to any obstruction.
i
a
ig
»
The
weight
of
the fan
is
21.07
pounds.
A DANGER: When using an existing outlet box, make sure it is securely attached to the building structure and can support the full
weight of the fan. Failure to this can result in serious injury or death. The stability of the outlet box is essential in minimizing wobbie
and noise in the fan after installation is complete.
A WARNING: Using a full-range dimmer switch to control fan speed will cause a humming sound from the fan. To reduce the risk of
fire or electric shock, do NOT use a full-range dimmer switch to control fan speed
A WARNING: To reduce the risk of fire, electric shock or personal injury, mount the fan to an outlet box marked “ACCEPTABLE
FOR FAN SUPPORT” and use the mounting screws provided with the outlet box. Most outlet boxes commonly used for the support of
lighting fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt. Secure the
5 outlet box directly to the building structure. The outlet box and its support must be able to support the moving weight of the fan (at
least 35 lbs.)
A WARNING: To reduce the risk of fire, electric shock or personal injury, wire connectors provided with this fan are designed to accept
onty one 12-gauge house wire and two lead wires from the fan. If your house wire is larger than 12-gauge and/or there is more than one
house wire to connect to the two fan lead wires, consult an electrician for the proper size wire connectors to use.
A WARNING: To reduce the risk of fire, electric shock or personal injury, do not bend the blade arms when installing them, balancing
the blades or cleaning the fan. Do not insert objects between the rotating fan blades
A WARNING: To reduce the risk of personal injury, use only parts provided with this fan. The use of parts other than those provided with
this fan will void the warranty.
CAUTION: Be sure the outlet box is properly grounded or a ground (green or bare) wire is present
CAUTION: Carefully check all screws, bolts, and nuts on the fan assembly ensure they are secured
Remote Kit
=]
008
Blade Balancing Kit
:
TTT
ime
©
(O)
Secondary
Support
Screw
Secondary
Spring
Support
Washer
Washer
Blade
Screw
(x
18)
Blade
Washer
(x
18)
Wire
Connector
(x
6)
Note: Some extra hardware may be in
luded.
The
quantity
listed
above
is
the
number
required
for
installation
2 3

SAFETY INFORMATION
f
CAUTION:
This
device
complies
with
Industry
Canada
license-exempt
RSS
standard(s).
Operation
Is
ae,
De
ete
two
conditions:
(1)
this
device
may
not
cause
interference,
and
(2)
this
device
must
accept
any
interference,
including
ice
that
may cause undesired operation of the device (if applicable)
CAN ICES-005 (B) / NMB-005 (B)
This
device
complies
with
Part
15
of
the
FCC
Rules.
Operation
is
subject
to
the
following
two
conditions:
(1)
this
device
may
not
cause
harmful
interference,
and
(2)
this
device
must
accept
any
interference
received,
including
interference
that
may
cause
undesired
operation.
This
equipment
has
been
tested
and
found
to
comply
with
the
limits
for
a
Class
B
digital
device,
pursuant
to
Part
15
of
the
FCC
Rules.
These
limits
are
designed
to
provide
reasonable
protection
against
harmful
interference
ina
residential
installation.
This
equipment
genera
uses
and can
radiate
radio
frequency
energy
and,
if
not
installed
and
used
in
accordance
with
the
instructions,
may
cause
harmful
interference
to
radio
communications.
However,
there
is
no
guarantee
that
interference
will
not
occur
ina
particular
nstallation.
If
this
equipment
does
cause
harmful
interference
to
radio
or
television
reception,
which
can
be
determined
by
turning
the
equipment
off
and
on,
the
user
is
encouraged
to
try
to
correct
the
interference
by
one
or
more
of
the
following
measures
—Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into and outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help
Please note changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
perate the equipment
Club Parkway #225
8125
CARE AND MAINTENANC
At least twice each year, lower the canopy to check the downrod assembly and tighten all screws on the fan. Clean the motor
housing and blades with a soft brush or lint-free cloth to avoid scratching the finish
Paglia Shut off the main power supply before you begin any maintenance task. Do NOT use water or a damp cloth to clean
the fan
PREPARATION
Before beginning the assembly of this product, ensure all parts are present. Compare all parts with the package contents list
and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.
Estimated assembly time: 2 hours
Tools required (not included): Electrical tape, Phillips Screwdriver, Safety Glasses, Step Ladder, and Wire Strippers.
1. Turn off power to the fan at the breaker box and the wall switch (Figure 1.1). DANGER: Failure to disconnect the power supply
prior to installation may result in serious injury or death.
2. Choose one of the following mounting options (Figure 1.2):
Standard Mount - best suited for ceilings 8 feet or higher. For very high ceilings, use a longer downrod (not included).
Angle
Mount
-
best
suited
for
angled
or
vaulted
ceilings.
A
longer
downrod
is
sometimes
necessary
to
ensure
proper
blade
clearance. Ensure the ceiling angle is not steeper than 10 degrees.
Flushmount Installation - not available for this model
Closemount Installation - not available for this model
3.
Choose
a
suitable
location
-
Ensure
the
blades
will
be
at
least
30
inches
from
any
obstructions.
Also
check
the
downrod
length to ensure the blades will be at least 7 feet above the floor (Figure 1.3).
=|
jin. min >
) iS
= 2
ae ony | =
Qy GV =
sid
Standard Mount Angle Mount
I \ots/
Flushmount Clasemount
Figure 1.1 Figure 1.2 Figure 1.3
INITIAL INSTALL.
ie)
1. Loosen all four mounting bracket screws and completely remove the two screws from the round holes in the canopy. Then
remove mounting bracket from the canopy and save them for later. Remove the canopy from the mounting bracket (Figure 2.1)
2. Install the mounting bracket to the outlet box (sold separately) using the screws and washers provided with the outlet box
(Figure 2.2),
3. Remove the 12 Phillips-head motor screws from the top of the motor assembly and save for blade arm assembly (Figure 2.3).
i ©® Installation»)
| oa Standard |
| Motor Screw
v
FF
—h | v
se | é
Canopy Mounting
Bracket Screw i
| Angle Mount
* = ce NX een npc a
Figure 2.1 Figure 2.2 Figure 2.3

cose: set screws In the yoke
Remave the downrod clip and dewnrod pin fram the downrod, Then partially loosen the two set scre yoke at the top
of the motor assembly (Figure 2.4).
Insert
the
downrod
through
the
canopy
and
yoke
cover
Feed
the
wires
and
braided
able
from
the
fan
through
the
downrod
(Figure 2.5)
6. Slide the dawnrod into the yoke of the motor assembly. Align holes and reinstall the downrod pin and downrod clip and
secure with the two set screws (Figure 2.6)
Depending on the length of downrod you use, you may want to cut the fan wires to simplify wiring After pulling the wires alt
the way through the downrod, measure 8 Inches of wire, Cut off the excess wire using wire cutters (not included). Warning:
Do NOT cut braided cable. Then strip 1/2 inch of insulation from the end of each wire strand (Figure 2.7)
the dewnrad into the mounting bracket. Rotate the downrod until the tab in the mounting bracket is seated in the slot
the downrod ball. WARNING: The fan and/or downrod should not rotate in the mounting bracket, If installed correctly
Fallure to align the slot in the downrod ball with the tab on the mounting bracket may result in fan falling causing serious
injury or death
9. Insert the receiver into the opening of the mounting bracket with flat side facing the ceiling (Figure 2.9)
Downrod Set Screw
Downrod Clip
{ @ Downrod Pin
$ Downrod Clip
Set Screw
cos di
Figure 2.5 Figure 2.6
Mounting
Bracket
Receiver
Figore 2.7 Figure 28 5
SECONDARY HANGING SYSTEM INSTRUCTIONS
For installation In the United States: Building codes in the U.S.A. do not require installation of a Secondary Hanging System
if desired, the braided cable can be cut and removed using wire cutters (sold separately). Skip to FINAL INSTALLATION. For
installation in Canada: in compliance with building codes in Canada, installation of the Secondary Hanging System is required.
1. Feed the loop of the braided cable, preassembled to the motor assembly, up through the outlet box mounted in the ceiling
(Figure 3.1)
2. Install secondary support screw, spring washer and support washer partly into the side of the brace installed in the ceiling
Then loop the braided cable up and over the ceiling brace and place the open loop of the braided cable around the secondary
support screw, Note: The ceiling support brace may not be accessible from below. If not, it must be accessed from above.
Important: The braided cable must make a complete circle around the support brace to secure the fan (Figure 3.2)
3. Tighten the secondary support screw, securing the braided cable (Figure 3.3).
Braided Cable
Open Loop Secondary
Support Screw a \, Secondary Support Screw
a
oon
\ t Support SS oy
a k Washer i
te —
|
‘ ) Spring
Washer
|
=
Figure 3.1 Figure 3.2 Figure 3.3
1. Use wire connectors to connect the fan wires and the receiver wires to the household supply wires according to the wiring
diagram and the following instructions (Figure 4 1):
« Connect the green wire from the downrod and mounting bracket to the Bare/Green (ground) supply wire.
* Connect the White wire (AC IN N) from the receiver to the White (neutral) supply wire.
* Connect the Black wire (AC IN L) from the receiver to the Black (hot/power) supply wire
* Connect the Black wire (TO MOTOR L) from the receiver to the Black fan wire.
* Connect the Blue wire (FOR LIGHT) from the receiver to the Blue fan wire.
* Connect the White wire (TO MOTOR N) from the receiver to the White fan wire
Align the canopy over the loosened mounting bracket screws. Place the J-slot of the canopy onto the mount bracket screws and
rotate clockwise. Secure the canopy with the two previously removed mounting bracket screws. Tighten all the mounting bracket
screws securely (Figure 4 2).
Partially insert three blade screws, along with their washers, through the blade and into the blade arm. Tighten each blade screw
with a Phillips screwdriver (not included), starting with the one in the middle. Repeat this step for the remaining blades and blade
arms (Figure 4.3).
Nv
w
Black (hot/power}
Blade Screw Blade Washer
Mounting Bracket Screw Blade
5 / — tT Ot
3 Bare/Green Te _
$ (ground)
a = =
as ) Blade Arm
Wire Connector
Figure 4.1 Figure 4.2 Figure 4.3

FINAL INSTALLATION
&
Attach
the
blade
arms
to
the
top
of
the
motor
assembly
using
the
motor
screws.
Completely
secure
each
blade
arm
to
the
motor
assembly
before
moving
to
next
(Figure
4.4)
Remove
one
of
the
three
fitter
plate
screws
preassembted
to
the
fitter
piate
and
loosen
the
other
two
but
do
not
remove.
Feed
the
9-pin
connector
through
center
hole
in
light
pan.
Align
the
slotted
holes
in
the
light
pan
with
the
toosened
screws
in
the
fitter
plate
Turn
light
kit
clockwise
and
replace
the
previously
removed
fitter
plate
screw.
Tighten
all
screws
(Figure
4.5)
va
one
of
the
three
light
pan
screws
from
the
light
pan.
Connect
the
9-pin
connectors
from
the
light
pan
to
the
9-pin
from
the
light
kit.
Lift
the
two
keyhole
stots
in
the
light
kit
over
the
two
loosened
light
pan
screws
and
tum
in
a
clockwise
direction
Then,
use
the
previously
removed
light
pan
screw
to
secure
the
light
kit
to
the
light
pan
(Figure
4.6).
Lift
the
glass
assembly
into
the
light
kit
and
twist
in
a
clockwise
direction
to
secure
(Figure
4
7).
Note:
Remove
the
rubber
shipping
blocks
from
the
glass
assembly.
Remove
the
battery
door
from
the
back
of
the
remote
using
a
flat-head
screwdriver
(not
included).
Insert
the
two
CR2032
batteries
into
the
remote,
ensure
the
positive
pole
of
the
batteries
face
up
(as
pictured)
and
then
replace
the
battery
door.
Press
the
HIGH
SPEED
button
to
ensure
the
LED
indicator
illuminates
and
the
fan
turns
on
(Figure
4.8)
9.
If
desired,
the
wall
bracket
can
be
attached
to
a
wall
using
the
mounting
screws
(Figure
4.9)
vy
~
o
Turn on power to fan at breaker box and the wail switch. Assembly is complete.
2
>
v
Motor Screw
— =) Light Pan
Fitter Plate &
Screw ‘
9-pin @ Light Pan
‘ Connector Screw
Figure 4.4 Figure 4.5 Figure 4.6 3
Mounting
Screw
| |
| Battery
| -— fc
Glass Assembly ( ——
Wall Bracket
Figure 4.7 Figure 4.8 Figure 49
OPERATING INSTRUCTIONS
1. To operate the fan using the remote, press and retease the following buttons (Figure 5.1)
A - Fan Off - Turns the power to fan off.
B - High Speed - Turns on fan at high speed
C - Medium Speed - Turns on fan at medium speed.
D - Low Speed - Turns on fan at low speed
E
-
Light
Delay
-
Light
Control:
Dimmable
Bulbs
-
Press
light
control
to
turn
lights
off
and
on.
Press
and
hold
light
control
to
dim
or
brighten
the
lights.
Non-dimmable
Bulbs
-Turns
the
lights
on
and
off.
Note:
The
dimmer
function
does
not
work
with non-dimmable bulbs
F
-
Light
Delay
Off
mode
-
Press
and
hold
the
fan
power
button
for
five
seconds,
which
will
turn
off
light
after
one
minute.
The LED indicator on the remote will flash four times to confirm mode setting
G-
Variable
Breeze
-
Simulates
a
breeze
in
nature.
Press
and
hold
button
to
activate
Press
any
fan
speed
button
to
cancel
H
-
Home
Shield™
-
Simulates
occupancy
while
away
from
home.
Fan
remains
off
and
the
light
randomly
turns
on
fora
minimum
of
five
times and
a
maximum
of
20
minutes.
The
light
remains
off for
60
minutes
between
events.
Press
and
hold
button
to
activate.
Light
will
blink
twice
to
confirm
Home
Sheild
is
active
Press
any
button
to
cancel
|
-
LED
indicator
-
should
illuminate
when
any
remote
button
is
pressed.
If
not,
replace
the
DC3V,
CR2032
batteries.
J
-
LEARN
button
-
Syncs
remote
to
receiver
(see
TROUBLESHOOTING
for
instructions).
Note:
To
access
LEARN
button
remove battery door from back of the remote using a flat-head screwdriver.
N
Use
the
reverse
switch
located
on
the
light
kit
to
optimize
your
fan
for
seasonal
performance
In
warmer
weather,
push
the
reverse
switch
left,
which
will
result
in
downward
airflow
creating
a
wind
chill
effect
In
cooler
weather,
push
the
reverse
switch
right
and
the
fan
to
low,
which
will
result
in
upward
airflow
that
can
help
move
stagnant,
hot
air
off
the
ceiling
area
(Figure
5.2)
Important:
Wait
for
the
fan
to
stop
before
moving
the
reverse
switch
located
on the
light
kit.
The
reverse
switch
must
be
set
either
completely
left
or
right
in
order
for
the
fan
to
function
correctly.
If
the
reverse
switch
is
set
in
the
middle
position,
the
fan
will
not
operate.
| Reverse Switch
Remove glass assembly by turning in a counter
clockwise direction to access the reverse switch.
Figure 5.1 = Figure 5.2

TROUBLESHOO G
If you experience any faults, please check the Troubleshooting section below. If a problem cannot be remedied or you are
experiencing difficulty in installation, please contact Customer Service: 1-877-361-3883
Warning: Shut off the power supply before you begin any maintenance task
PROBLEM
The fan does not
move.
The fan is noisy.
The fan wobbles
excessively.
The fan operates
correctly but the lights
are not working.
Remote does not
work
CORRECTIVE ACTION
Firmly push the reverse switch completely left or right
Make sure the wall switch is turned on.
Turn the power on or check the fuse (breaker).
Turn the power off and check all connections at the ceiling outlet box.
rPwnre
Check and tighten all screws that hold the fan blades to the blade arms and the motor.
Replace the cracked blade
Do not use a full range dimmer switch to control the fan speed
Ensure the outlet box is secured to the building structure.
Ensure the mounting bracket is secured to the outlet box and that the screws are tight
OPWNe
-
Check and tighten all screws that hold the fan blades to the blade arms and the blade arms to the
motor.
Switch one blade with a blade from the opposite side, or balance the fan using the blade
balancing kit
Turn off the power. Loosen the canopy and verify that the mounting bracket is secure to the
electrical outlet box. The bracket must be flush without movement against the outlet box. Verify
the outlet box is secure.
Use a longer downrod (sold separately) or move the fan to another location.
Lift up the yoke cover and tighten the set screws on the yoke until secure.
N
w
ap
Ensure the 9-pin connectors in the light kit are connected properly.
Turn the power off and check all connections at the ceiling outlet box.
NE
1. Power surge may have cleared the memory and remote needs to be resynced to the receiver.
Syncing instructions: Turn off the main power, then turn it back on. Within 30 seconds, press and
hold
the
HIGH
SPEED
and
LOW
SPEED
buttons
(or
the
“LEARN”
button,
located
in
the
battery
compartment) for S seconds. Fan will turn on at low speed and light off. This confirms the syncing
process is successful
2. Insert new CR2032 batteries in battery compartment of the wall control.
3. If there are several remote fans in proximity, turn the power off to those fans and re-sync the fan.
10
LIMITED LIFETIME WARRANTY
Set forth below, the manufacturer, Hong Kong China Electric Appliance Company (HKC) warrants the fan motor for this ceiling
fan to be free from defects In workmanship and material for the life of the product. Also, subject to the limitations below, HKC
warrants all ceiling fan parts (“ceiling fan parts” excludes the motor and parts made in whole or in part with glass) to be free
from defects in workmanship and material for a period of one year after the date of purchase by the original purchaser at retail.
All claims must be made by the original purchaser, whether such purchaser purchased the product through a store or
contractor. Ceiling fan part defects must be reported within the first year from the date of purchase. Parts made in whole or in
part with glass and the finishes of metal and other surfaces are not warranted
Purchasers are responsible for all costs of removing and reinstalling the product. Any damage to any part caused by ordinary
wear and tear, accident, misuse, or improper installation, is not covered by this warranty. HKC assumes no responsibility
whatsoever for fan installation. Any service performed by a non-licensed electrician will render the warranty invalid.
HKC's sole responsibility shall be to repair or replace the motor, parts, or product within the terms stated above. HKC shall not
be liable for any loss or damage of any kind, including any incidental or consequential damages resulting directly or indirectly,
from any breach of warranty, express or implied, or any other failure of this product. Some states do not allow the exclusion or
limitation of incidental or consequential damages so this limitation may not apply to you
If the original purchaser ceases to own the fan, this warranty is voided.
Should the purchaser encounter a problem with your fan related to defects in workmanship or materials within the warranty
period associated with the defective part, HKC agrees to replace the defective part without charge, or at its option, to replace the
ceiling fan with a comparable or superior model.
HKC’s warranties are limited to the written warranties set out in this HKC ceiling fan limited lifetime warranty. All other express
and implied warranties, including, without limitation, the implied warranty of fitness for a particular purpose and the implied
warranty of merchantability are disclaimed. Some states do not allow the disclaimer of implied warranties, so this disclaimer
may not apply to you.
PLACEMENT PARTS LIST
For replacement parts, call our customer service department 1-877-361-3883. Monday-Friday, 8am - Spm, Central Time.
roptode
@
51035 51036 51477 51626
Glass Assembly 44000010610 44000010650 44000013280 44000014230
Blade Arm (x6) 44073920001 44073920002 44073920004 44073920005
Blade (x 6) 44085300001 44085300002 44085300005 44085300006
Remote Pack ojo|a}>
44000013090 44000013090 440000130390 44000013090
HW | Hardware Bag 44000013300 44000013310 44000013290 44000014240
The Honeywell Trademark is used under license
from Honeywell international Inc ™
Honeywell International Inc. makes no
representations or warranties with respect to this
product
This product is manufactured for
Hong Kong China Electric Appliance, LTD.
3350 Players Club Parkway, Suite 225
Memphis, TN 38125
1 [phone] 9597 * 061220
(oo one on erence