Honeywell VERTEX C User manual

USER
MANUAL
VERTEX C ANALYZER

Vertex Compliance System
2
User Manual
Contents
1 Safety ...........................................................................................................................................................................3
Trademarks......................................................................................................................................................................3
General Safety.................................................................................................................................................................3
Continuous Monitor Symbols..........................................................................................................................................3
FCC Compliance Statement.............................................................................................................................................4
NCC Compliance Statement ............................................................................................................................................4
Connectors.......................................................................................................................................................................6
2Introduction.................................................................................................................................................................7
Analyzer side panel —Exterior....................................................................................................................................7
Analyzer side panel —Interior.....................................................................................................................................9
Analyzer —Front view ................................................................................................................................................9
Chemcassette...............................................................................................................................................................9
Clean the Optics ............................................................................................................................................................11
3 Additional Information................................................................................................................................................12
Specifications.................................................................................................................................................................12

Vertex Compliance System
5
User Manual
CHAPTER
1 Safety
Read this information before you start using your device.
Trademarks
Brand or product names are trademarks of their respective owners. The following brand orproduct names are
trademarks of Honeywell:
⚫Honeywell Vertex™ Compliance
⚫Chemcassette®
⚫Teflon®
⚫Sola/Hevi-Duty
General Safety
Follow all installation and operational instructions to ensure the safe and reliable operation of thisunit. If this
monitor is used in a manner not specified by Honeywell Analytics Inc., the protection provided by the equipment
could be impaired.
Continuous Monitor Symbols
Symbol
Description
Lifting instructions, low clearances, slipping/tripping hazards, minor corrosive
dangers. Also used when defining personal protective equipment(gloves, dust
masks, etc.)
Personal injury risk: machinery hazards around guarded equipment, moving parts,
crush/pinch hazards, flying debris, and arc flash hazards.
The most dangerous or potentially lethal hazards: unguarded equipment,confined
space entrances, and lockout labels.
Caution: possibility of electric shock

4
User Manual
Symbol
Description
Caution: hot surface
Protective conductor terminal (ground terminal)
EMC Considerations
Your Honeywell Analytics continuous gas monitor has been designed to comply with Electromagnetic
Compatibility (EMC) standards applicable at the time of its manufacturing. Thedesign includes filtering, shielding
and bypassing techniques. At the time of certification, simulated customer Input/ Output (I/O) schemes were
tested.
All methods used in your equipment for emission suppression and reduction of susceptibilityare interactive.
Modifications to the monitor could result in increased emissions and higher vulnerability to other radiated
fields.
Following the guidelines in this EMC Considerations section will ensure your monitor maintainsthe enhanced
degree of EMC integrity. The guidelines listed apply only to I/O emissions and do not apply to A.C. and D.C.
monitor power connections.
FCC Compliance Statement
CAUTION: Changes or modifications not expressly approved could void your authority to use thisequipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must acceptany interference received,
including interference that may cause undesired operation.
NCC Compliance Statement
取得審驗證明之低功率射頻器材，非經核准，公司、商號或使用者均不得擅自變更頻率、加大功率
或變更原設計之特性及功能。低功率射頻器材之使用不得影響飛航安全及干擾合法通信；經發現有
干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前述合法通信，指依電信管理法規定
作業之無線電通信。低功率射頻器材須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之
干擾。
Without permission granted by the NCC, any company, enterprise, or user is not allowed to change
frequency, enhance transmitting power or alter original characteristic as well as performance to an
approved low power radio-frequency devices. The low power radio-frequency devices shall not influence
aircraft security and interfere legal communications; If found, the user shall cease operating immediately
until no interference is achieved. The said legal communications means radio communications is
operated in compliance with the Telecommunications Management Act. The low power radio-frequency

5
User Manual
devices must be susceptible with the interference from legal communications or ISM radio wave radiated
devices.
Cabling
At the very minimum, all cables should include a braided shield. Ideal results have been obtainedwith twisted
pair cabling which has a foil shield surrounding each pair plus foil and 90% braid shielding around the bundle.
In addition, ensure local electrical code requirements are met.
The next cable parameters must be considered:
Braid
Must have a minimum 90% coverage
Foil
When used with braid, provides 100% coverage.
Do not use foil alone. It has a tendency to break.
Twisted Pair
Provides for cancelling of magnetic fields
Stranded
Pair
Provides the greatest surface area
Shield
Termination
Continuation of the shield to the cabinet earth ground is mostimportant.
For discrete wire terminations, pigtails to the cabinet (connector)ground should be
extremely short (no greater than three inches).
For multiconductor connector terminations, only 360° shielded
shells should be used.

6
User Manual
Connectors
All qualification and certification of Honeywell Analytics products were achieved with high quality connectors,
providing 360° shield coverage. These connectors generally had metal shells.
Failure to properly secure the connector to the equipment will result in high emission levels. Also, poorly
constructed, or improperly assembled connectors can be a high source of radiatednoise and provide a path
for external signals into the monitor.

Vertex Compliance System
7
User Manual
CHAPTER
2Introduction
Analyzer side panel —Exterior

Vertex Compliance System
8
User Manual
1. Needle Valve for flow adjustment
2. Optics Block
3. RFID reader
4. Take-up reel
5. Tape guide roller
1. Analyzer Number Tag
2. Analyzer Status LED.
3. Analyzer Release Button

Vertex Compliance System
9
User Manual
Analyzer side panel —Interior
1. Analyzer Main Board
2. Sample pressure transducers
3. Sample flow transducers
Analyzer —Front view
1. Analyzer Status LED
2. Analyzer Number Tag
Chemcassette

Vertex Compliance System
10
User Manual