Honeywell Dolphin CT60 User manual

Dolphin™ CT60
Mobile Computers for use in Hazardous Locations
Dolphin CT60 (CT60-L0N-xSxxx1E)
Dolphin CT60 (CT60-L1N-xSxxx1E)

powered by Android™
CT60-ATEX-A-EN-QS Rev A
6/19

Introduction
This document is only for Dolphin CT60 models marked as
certified for use in hazardous environments. Dolphin CT60
models intended for use in hazardous locations are identifiable
by specific labeling on the back of the device.
Out of the Box
Make sure that your shipping box contains these items:
• Dolphin CT60 mobile computer 
(CT60-L0N-xSxxx1E or CT60-L1N-xSxxx1E)
• Rechargeable Li-ion battery
• Product documentation
Note: CT60L0N models do not include a WWAN radio.
Memory Card Specifications
Honeywell recommends the use of Single Level Cell (SLC)
industrial grade microSD™ or microSDHC™ memory cards with
Dolphin mobile computers for maximum performance and
durability. Contact a Honeywell sales representative for 
additional information on qualified memory card options.
Before you attempt to use, charge or replace the battery in
the device, carefully read all labels, markings and product
documentation provided in the box or online at
www.honeywellaidc.com.

Equipment for Use in Hazardous Locations
Routine operator inspections should occur to check for possible
device damage before using the mobile computer in areas
known to be hazardous.
Caution: Improper battery replacement or incompatible
device usage may result in risk of burns, fire, explosion, or
other hazard. Dispose of batteries according to local
regulations.
Mesee en garde: Le remplacement incorrect de la pile ou
l'usage d'un appareil non compatible peut représenter des
risques de brûlures, d'incendie, d'explosion ou d'autres
dangers. Éliminez les piles lithium-ion usagées
conformément aux réglementations locales.
Warning: Explosion Hazard - Batteries must only be changed
or charged in an area known to be non-hazardous.
Use ONLY Honeywell CT60 battery part number 
318-055-013 (Li-ion, 3.85 VDC) or 
318-055-016 (Li-ion, 3.86 VDC).
Risqued’explosion-Les batteries doivent uniquement être
remplacées ou rechargées dans un endroit non dangereux.
Utilisez UNIQUEMENT Honeywell CT60 batterie 
P/N 318-055-013 (Li-ion, 3.85 VDC) ou 
318-055-016 (Li-ion, 3.86 VDC).
Additional spare batteries must not be carried in the
hazardous area.
Warning: Explosion Hazard - Substitution of any
components may impair suitability.
Avertissement: Risque d’explosion - La substitution de
composants peut nuire à l’aptitude aux emplacements.
Warning: The device must be protected from impacts with
high impact energy, permanent UV light emission and high
electrostatic discharge processes.

Scan Buttons
Microphone
Power
Button
Battery Status /
Notification LED
Good Read LED
Speaker
Touch Panel
Volume Buttons
Navigation Panel
Mobile Computer Features

Camera Lens
Battery
Camera Button
Battery Latch
Imager
(LED / Laser Aperture)
SIM Card 1 Door
SIM Card 2 Door
(CT60L1N Model)
microSD Card
Door
Laser Safety
Label Location
I/O Connector
Note: Hand strap not shown.

3 4
1
5
2
Install a microSD Card (SD)
Note: Format the microSD card before initial use.
Note: Always power off the computer and remove the battery before
attempting to install or remove a card.

3 4
1
5
2
Install a microSIM Card (SIM 1)
Note: Feature available on CT60L1N Models only.
Note: Always power off the computer and remove the battery before
attempting to install or remove a card.

3 4
1
5
2
Install a Secondary microSIM Card (SIM 2)
Note: Feature available on CT60L1N Models only.
Note: Always power off the computer and remove the battery before
attempting to install or remove a card.

1
23
Install the Battery
The CT60 mobile computer ships with a Li-ion battery, manu-
factured for Honeywell International Inc.
Before you attempt to use, charge, or replace the battery in
the mobile computer, carefully read all the information
under “Equipment for Use in Hazardous Locations”.
Ensure all components are dry prior to placing the battery in
the computer. Mating wet components
may cause damage not covered by the warranty.
Warning: Battery must be locked when using the CT60 in a
hazardous environment.
AVERTISSEMENT: la batterie doit être verrouillée lors de
l'utilisation du CT60 dans un environnement dangereux.

Charge the Mobile Computer
The CT60 mobile computer ships with a partially charged 
battery. Charge the battery with a CT50 Series charging device
for a minimum of 4 hours. Using the computer while charging
the battery increases the time required to reach a full charge.
CT60 mobile computers are designed for use with the following
CT50 Series charging accessories: HomeBase, Ethernet 
HomeBase, ChargeBase, NetBase, Quad Battery Charger, 
Vehicle Power Adapter, Vehicle Dock, and USB Adapter.
Before you attempt to use, charge, or replace the battery in
the mobile computer, carefully read all the information
under “Equipment for Use in Hazardous Locations”.
We recommend the use of Honeywell accessories and power
adapters. Use of any non-Honeywell accessories or power
adapters may cause damage not covered by the warranty.
Mise en garde: Il est recommandé d'utiliser les
périphériques, les cordons d'alimentation et les adaptateurs
secteur conçus par Honeywell. L'utilisation de tout
périphérique, cordon d'alimentation ou adaptateur secteur
d'une autre marque est susceptible de provoquer des
dommages non couverts par la garantie.
Ensure all components are dry prior to mating the computers
and batteries with peripheral devices. Mating wet
components may cause damage not covered by the warranty.
Mise en garde: Assurez-vous que tous les composants sont
secs avant de connecter les terminaux/batteries à des
périphériques. L'insertion de composants humides risque de
provoquer des dommages non couverts par la garantie.
We recommend use of Honeywell Li-ion battery packs. Use
of any non-Honeywell battery may result in damage not
covered by the warranty.

Turn Power On/Off
The first time you power on the computer, a Welcome screen
appears. You can either scan a configuration bar code or use the
Wizard to manually set up the computer. Once setup is 
complete, the Welcome screen no longer appears on startup
and Provisioning mode is automatically turned off (disabled).
To turn the computer on:
• Press and release the Power button.
To turn the computer off:
1. Press and hold the Power button until the options menu
appears.
2. Touch Power Off.
Note: You should always power off the computer before removing the
battery.
Sleep Mode
Sleep mode automatically turns the touch panel display off and
locks the computer to save battery power when the computer is
inactive for a programmed period of time.
1. Press and release the Power button to wake the computer.
2. Drag the toward the top of the display to unlock the
computer.

Notification /
Status Bar
Search Bar
Touch to
initiate a voice
search or
command.
Home Screen
Panel
Touch to
access all apps.
Favorites Tray
About the Home Screen
To learn how to customize the Home screen, see the user guide.

Button Description
Back Return to the previous screen.
Recent Apps View and switch between
recently used apps.
Home Return to the Home screen.
Search Start a search on the computer
or the Internet.
Volume Raise or lower the volume of the
speaker.
Scan Press right or left scan button to
trigger the scanner.
Camera Press to open the camera app
and take a photo.
Navigation and Function Buttons
To learn more about how to re-map a button, see the user guide.

About Provisioning Mode
After completing the out-of-box set up process, Provisioning
mode is automatically turned off. Scanning a bar code to install
applications, certificates, configuration files, and licenses on
the computer is restricted unless you enable Provisioning mode
in the Settings app. To learn more, see the user guide.
Scan a Bar Code with the Scan Demo
Note: For optimum performance, avoid reflections by scanning the bar
code at a slight angle.
1. Touch > Demos > Scan Demo.
2. Point the computer at the bar
code.
3. Touch Scan on the screen or
press and hold any Scan
button. Center the aiming
beam over the bar code.
The decode results appear on the screen.
Note: In the Scan Demo app, not all bar code symbologies are enabled
by default. If a bar code does not scan, the correct symbology may
not be enabled. To learn how to modify the default app settings,
see the user guide.
Sync Data
To move files between your CT60 and a computer:

1. Connect the CT60 to your computer using a USB charge/
communication accessory.
2. On the CT60, swipe down from the top of the screen to
access the notifications panel.
3. Touch the Android System USB Connection notification
twice, to open the options menu.
4. Select either Transfer files or Transfer photos (PTP).
5. Open the file browser on your computer.
6. Browse to the CT60. You can now copy, delete and/or move
files or folders between the computer and CT60 or a
microSD card installed in the CT60 as you would with any
other storage drive (e.g., cut and paste or drag and drop).
Note: When Provisioning mode is turned off, some folders are hidden
from view in the file browser.
Restart the Mobile Computer
You may need to restart the mobile computer to correct condi-
tions where an application stops responding to the system or
the computer seems to be locked up.
1. Press and hold the Power button until the options menu
appears.
2. Select Restart.
To restart the computer if the touch panel display is unrespon-
sive:
•PressandholdthePower button for approximately 8 seconds
until the computer restarts.
Note: To learn about advanced reset options, see the user guide.

Support
To search our knowledge base for a solution or log into the 
Technical Support Portal and report a problem, go to 
www.hsmcontactsupport.com.
Documentation
Product documentation is available at www.honeywellaidc.com.
Limited Warranty
For warranty information, go to www.honeywellaidc.com and
click Get Resources > Product Warranty.
Patents
For patent information, see www.hsmpats.com.
Trademarks
Android is a trademark of Google LLC.
Disclaimer
Honeywell International Inc. (“HII”) reserves the right to make
changes in specifications and other information contained in
this document without prior notice, and the reader should in all
cases consult HII to determine whether any such changes have
been made. The information in this publication does not repre-
sent a commitment on the part of HII.
HII shall not be liable for technical or editorial errors or omis-
sions contained herein; nor for incidental or consequential
damages resulting from the furnishing, performance, or use of
this material. HII disclaims all responsibility for the selection
and use of software and/or hardware to achieve intended
results.

This document contains proprietary information that is pro-
tected by copyright. All rights are reserved. No part of this docu-
ment may be photocopied, reproduced, or translated into
another language without the prior written consent of HII.
Copyright © 2019 Honeywell International Inc. All rights
reserved.