Honeywell ScanPal EDA61K Series User manual

ScanPal™ EDA61K Series
Mobile Computer powered by Android™
Quick Start Guide
EDA61K-A-EN-QS-01 Rev A
02/20

1
Out of the Box
Make sure that your shipping box contains these items:
• ScanPal Mobile Computer
(Model EDA61K-0 or EDA61K-1)
• Rechargeable 3.6 V Li-ion battery
• Product documentation
If you ordered accessories for your mobile computer, verify that
they are also included with the order. Be sure to keep the original
packaging in case you need to return the mobile computer for
service.
Note: EDA61K-0 models do not include a WWAN radio.
Memory Card Specifications
Honeywell recommends the use of Single Level Cell (SLC)
industrial grade microSD™ or microSDHC™ memory cards with
ScanPal mobile computers for maximum performance and
durability. Contact a Honeywell sales representative for
additional information on qualified memory card options.

2
Mobile Computer Features
Microphone
Power Indicator
Touch Panel
Scan Button
Scan Engine
Scan Indicator
Power Button
Keyboard
(model dependent)

3
Camera Flash/Flashlight
(model dependent)
Micro SIM Card and
MicroSD Card Cover
(battery removed)
Laser Safety
Label Location
I/O Connector
Speaker Battery
Battery Latch and
Button
USB Port
Hand Strap
(optional accessory)
Scan Button

4
Install a Micro SIM Card
Only EDA61K-1 (WWAN) models support micro SIM card use for
cellular phone features.
Note: Always power off the computer before attempting to install
or remove a card.
1
2
345

5
Install a microSD Card (Optional)
Note: Format the microSD card before initial use.
Note: Always power off the computer before attempting to install
or remove a card.
123

6
Install the Battery
The EDA61K ships with a Li-ion 3.6 V battery manufactured for
Honeywell International Inc.
We recommend use of Honeywell Li-ion battery
packs. Use of any non-Honeywell battery may result
in damage not covered by the warranty.
Ensure all components are dry prior to placing the
battery in the computer. Mating wet components may
cause damage not covered by the warranty.
1
2

7
Install Hand Strap (Optional Accessory)
12
3
4

8
Charge the EDA61K
The EDA61K mobile computer ships with a partially charged
battery. Charge the battery with an EDA61K charging device for
a minimum of 5 hours. Using the computer while charging the
battery increases the time required to reach a full charge.
EDA61K mobile computers are designed for use with the
following EDA61K charging accessories: Home Base, Quad
charger and USB Cable. For information about accessories, see
the ScanPal EDA60K/EDA61K Series Enterprise Mobile
computer Accessories Guide” at www.honeywellaidc.com.
Turn Power On/Off
The first time you power on the computer, a Welcome screen
appears. You can either scan a configuration barcode or use the
Wizard to manually set up the computer. Once setup is
complete, the Welcome screen no longer appears on startup
and Provisioning mode (see page 13) is automatically turned off
(disabled).
To turn the computer on:
• Press and hold the Power button for approximately 3 seconds,
and then release.
We recommend the use of Honeywell accessories and
power adapters. Use of any non-Honeywell
accessories or power adapters may cause damage not
covered by the warranty.
Ensure all components are dry prior to mating the
computers and batteries with peripheral devices.
Mating wet components may cause damage not
covered by the warranty.

9
To turn the computer off:
1. Press and hold the Power button until the options menu
appears.
2. Touch Power off.
Note: You should always power off the computer before
removing the battery.
Remove the Battery
Battery Replacement
Hot Swap
You can replace the battery on demand provided the following
conditions are met:
• The computer has been powered on for at least 4 minutes.
AND
• You insert a new battery within 30 seconds.
12
3