Honeywell UDC 2300 User manual

Sensing and Control
UDC 2300
Universal Digital Controller
User Manual
51-52-25-83D
4/00

ii UDC2300 Universal Digital Controller User Manual 4/00
Notices and Trademarks
Copyright 2000 by Honeywell
Release D April, 2000
Warranty/Remedy
Honeywell warrants goods of its manufacture as being free of defective materials and faulty workmanship. Contact your local
sales office for warranty information. If warranted goods are returned to Honeywell during the period of coverage, Honeywell
will repair or replace without charge those items it finds defective. The foregoing is Buyer’s sole remedy and is in lieu of all
other warranties, expressed or implied, including those of merchantability and fitness for a particular purpose.
Specifications may change without notice. The information we supply is believed to be accurate and reliable as of this
printing. However, we assume no responsibility for its use.
While we provide application assistance personally, through our literature and the Honeywell web site, it is up to the
customer to determine the suitability of the product in the application.
Sensing and Control
Honeywell
11 West Spring Street
Freeport, IL 61032
UDC2300 is a U.S. registered trademark of Honeywell
Other brand or product names are trademarks of their respective owners.

4/00 UDC2300 Universal Digital Controller User Manual iii
About This Document
Abstract
This document provides descriptions and procedures for the Installation, Configuration, Operation, and Troubleshooting of
your UDC2300 Controller. For a full UDC2300 product manual, request document number 51-52-25-73.
Contacts
World Wide Web
The following lists Honeywell’s World Wide Web sites that will be of interest to our customers.
Honeywell Organization WWW Address (URL)
Corporate http://www.honeywell.com
Sensing and Control http://www.honeywell.com/sensing
International http://www.honeywell.com/Business/global.asp
Telephone
Contact us by telephone at the numbers listed below.
Organization Phone Number
United States and Canada Honeywell 1-800-423-9883 Tech. Support
1-888-423-9883 Q&A Faxback
(TACFACS)
1-800-525-7439 Service
Asia Pacific Honeywell Asia Pacific
Hong Kong (852) 2829-8298
Europe Honeywell PACE, Brussels, Belgium [32-2] 728-2111
Latin America Honeywell, Sunrise, Florida U.S.A. [phone]

iv UDC2300 Universal Digital Controller User Manual 4/00
Symbol Definitions
The following table lists those symbols used in this document to denote certain conditions.
Symbol Definition
This CAUTION symbol on the equipment refers the user to the Product Manual for
additional information. This symbol appears next to required information in the
manual.
WARNING
PERSONAL INJURY: Risk of electrical shock. This symbol warns the user of a
potential shock hazard where HAZARDOUS LIVE voltages greater than 30 Vrms,
42.4 Vpeak, or 60 VDC may be accessible. Failure to comply with these
instructions could result in death or serious injury.
ATTENTION, Electrostatic Discharge (ESD) hazards. Observe precautions for
handling electrostatic sensitive devices
Protective Earth (PE) terminal. Provided for connection of the protective earth (green
or green/yellow) supply system conductor.
Functional earth terminal. Used for non-safety purposes such as noise immunity
improvement. NOTE: This connection shall be bonded to protective earth at the
source of supply in accordance with national local electrical code requirements.
Earth Ground. Functional earth connection. NOTE: This connection shall be bonded
to Protective earth at the source of supply in accordance with national and local
electrical code requirements.
Chassis Ground. Identifies a connection to the chassis or frame of the equipment
shall be bonded to Protective Earth at the source of supply in accordance with
national and local electrical code requirements.

4/00 UDC2300 Universal Digital Controller User Manual v
Contents
1 INTRODUCTION...................................................................................................1
1.1 Overview........................................................................................................................1
1.2 CE Conformity (Europe).................................................................................................2
2 INSTALLATION.....................................................................................................3
2.1 Overview........................................................................................................................3
2.2 Preliminary Checks........................................................................................................3
2.3 Control and Alarm Relay Contact Information................................................................6
2.4 Mounting........................................................................................................................7
2.5 Wiring ............................................................................................................................9
2.6 Wiring the Controller....................................................................................................11
2.7 Initial Start-up...............................................................................................................17
2.8 Operator Interface and Key Functions .........................................................................18
3 CONFIGURATION ..............................................................................................19
3.1 Overview......................................................................................................................19
3.2 Configuration Procedure..............................................................................................19
3.3 Timer Set Up Group.....................................................................................................22
3.4 Tuning Set Up Group...................................................................................................23
3.5 SP Ramp Set Up Group...............................................................................................25
3.6 Accutune Set Up Group...............................................................................................27
3.7 Algorithm Set Up Group...............................................................................................28
3.8 Input 1 Set Up Group...................................................................................................29
3.9 Input 2 Set Up Group...................................................................................................31
3.10 Control Set Up Group ..................................................................................................32
3.11 Options Set Up Group..................................................................................................34
3.12 Communications Set Up Group ...................................................................................35
3.13 Alarms Set Up Group...................................................................................................37
4 OPERATION .......................................................................................................39
4.1 Powering Up the Controller..........................................................................................39
4.2 Monitoring Your Controller...........................................................................................39
4.3 Single Display Functionality .........................................................................................42
4.4 Start Up Procedure for Operation ................................................................................44

vi UDC2300 Universal Digital Controller User Manual 4/00
4.5 Setpoints......................................................................................................................45
4.6 Timer ...........................................................................................................................46
4.7 Accutune II...................................................................................................................47
4.8 Fuzzy Overshoot Suppression.....................................................................................47
4.9 Using Two Sets of Tuning Constants...........................................................................48
4.10 Alarms .........................................................................................................................49
4.11 Three Position Step Control Algorithm.........................................................................50
4.12 Setting a Failsafe Output Value for Restart After a Power Loss...................................51
4.13 Setting Failsafe Mode..................................................................................................52
4.14 Entering a Security Code.............................................................................................53
4.15 Lockout Feature...........................................................................................................54
4.16 Background Tests........................................................................................................55
4.17 Restore Factory Calibration .........................................................................................57
5 SETPOINT RATE/RAMP/PROGRAM OPERATION........................................... 59
5.1 Setpoint Rate...............................................................................................................59
5.2 Setpoint Ramp.............................................................................................................59
5.3 Setpoint Ramp/Soak Programming..............................................................................61
6 APPENDIX A - ENVIRONMENTAL AND OPERATING CONDITIONS ..............67
7 APPENDIX B - MODEL SELECTION GUIDE.....................................................69
8 APPENDIX C - CONFIGURATION RECORD SHEET........................................71

4/00 UDC2300 Universal Digital Controller User Manual vii
Tables
Table 2-1 Preliminary Checks __________________________________________________3
Table 2-2 Control Relay Contact Information ______________________________________6
Table 2-3 Alarm Relay Contact Information _______________________________________6
Table 2-4 Mounting Procedure _________________________________________________8
Table 2-5 Permissible Wiring Bundling __________________________________________10
Table 2-6 Universal Output Functionality and Restrictions ___________________________10
Table 3-1 Configuration Procedure _____________________________________________21
Table 3-2 TIMER Group (Numeric Code 100) Function Prompts ______________________22
Table 3-3 TUNING Group (Numeric Code 200) Function Prompts_____________________23
Table 3-4 SPRAMP Group (Numeric Code 300) Function Prompts ____________________25
Table 3-5 ATUNE Group (Numeric Code 400) Function Prompts______________________27
Table 3-6 ALGOR Group (Numeric Code 500) Function Prompts _____________________28
Table 3-7 INPUT1 Group (Numeric Code 600) Function Prompts _____________________29
Table 3-8 INPUT2 Group (Numeric Code 700) Function Prompts _____________________31
Table 3-9 CONTRL Group (Numeric Code 800) Function Prompts ____________________32
Table 3-10 Options Group (Numeric Code 900) Function Prompts ____________________34
Table 3-11 Communications Group (Numeric Code 1000)___________________________35
Table 3-12 ALARMS Group (Numeric Code 1100) Function Prompts __________________37
Table 4-1 Annunciators ______________________________________________________39
Table 4-2 Lower Display Key Parameter Prompts__________________________________40
Table 4-3 Error Messages____________________________________________________41
Table 4-4 Single Display Parameters ___________________________________________43
Table 4-5 Procedure for Starting Up the Controller_________________________________44
Table 4-6 Procedure for Switching Between Setpoints ______________________________45
Table 4-7 Set Up Procedure __________________________________________________48
Table 4-8 Procedure for Switching PID SETS from the Keyboard _____________________48
Table 4-9 Procedure for Displaying Alarm Setpoints________________________________49
Table 4-10 Procedure for Displaying 3Pstep Motor Position__________________________50
Table 4-11 Procedure for Setting a Failsafe Value _________________________________51
Table 4-12 Procedure for Setting a Failsafe Mode _________________________________52
Table 4-13 Procedure to Enter a Security Code ___________________________________53
Table 4-14 Background Tests _________________________________________________55
Table 4-15 Restore Factory Calibration__________________________________________57
Table 5-1 Running A Setpoint Ramp____________________________________________60
Table 5-2 Program Contents __________________________________________________62
Table 5-3 Run/Monitor Functions ______________________________________________66

viii UDC2300 Universal Digital Controller User Manual 4/00
Figures
Figure 1-1 UDC2300 Operator Interface __________________________________________1
Figure 2-1 Jumper Placements _________________________________________________5
Figure 2-2 Mounting Dimensions (not to scale)_____________________________________7
Figure 2-3 Mounting Method ___________________________________________________8
Figure 2-4 Composite Wiring Diagram __________________________________________11
Figure 2-5 Mains Power Supply________________________________________________12
Figure 2-6 Input 1 Connections ________________________________________________12
Figure 2-7 Input 2 Connections ________________________________________________12
Figure 2-8 Electromechanical Relay Output ______________________________________13
Figure 2-9 Solid State Relay Output ____________________________________________13
Figure 2-10 Open Collector Relay Output ________________________________________14
Figure 2-11 Current Output ___________________________________________________14
Figure 2-12 External Solid State Relay Option (Internal Open Collector Output) __________15
Figure 2-13 Three-Position Step Control Connections ______________________________15
Figure 2-14 Alarm and Duplex Output Connections ________________________________16
Figure 2-15 External Interface Option Connections ________________________________16
Figure 2-16 Transmitter Power for 4-20 mA —2 wire Transmitter Using Open Collector
Alarm 2 Output (Model DC230B-XT-XX-XX-XXXXXXX-XX-X)________________17
Figure 2-17 Transmitter Power for 4-20 mA —2 Wire Transmitter Using Auxiliary Output
(Model DC230B-XX-2X-XX-XXXXXXX-XX-X)_____________________________17
Figure 2-18 Operator Interface and Key Functions_________________________________18
Figure 3-1 Prompt Hierarchy __________________________________________________20
Figure 5-1 Ramp/Soak Profile Example _________________________________________64
Figure 5-2 Program Record Sheet _____________________________________________65

Introduction
4/00 UDC2300 Universal Digital Controller User Manual 1
1 Introduction
1.1 Overview
The UDC 2300 is a microprocessor-based stand-alone controller. It combines
reliability and operating simplicity in a cost-effective 1/4-DIN size controller.
The UDC 2300 monitors and controls temperatures and other variables in
applications such as environmental chambers, plastic processing machines,
furnaces and ovens, and packaging machinery.
Its features include:
•Universal AC Power Supply,
•Input/Output Isolation,
•Isolated Auxiliary Current Output / Digital Input,
•Modbus and ASCII Communications,
•Timer,
•Accutune II Tuning with Fuzzy Logic Overshoot Suppression,
•2nd Input (Remote Setpoint),
•Setpoint Ramp/Rate/Program,
•Three Position Step Control,
•Duplex (Heat/Cool).
The UDC 2300 is also downward compatible with existing UDC 2000
applications and installations except for RTD and 0-10 Volt inputs.
See wiring diagrams in Section 2 - Installation.
ALM
OUT
PV
F
FUNCTION
AUTO
TUNE
MAN-AUTO
RESET SET UP
RUN
HOLD
C
RL
12
12
SP 2300
2300
DISPLAY
MA
Figure 1-1 UDC2300 Operator Interface

Introduction
2 UDC2300 Universal Digital Controller User Manual 4/00
1.2 CE Conformity (Europe)
This product is in conformity with the protection requirements of the following
European Council Directives: 73/23/EEC, the Low Voltage Directive, and
89/336/EEC, the EMC Directive. Conformity of this product with any other “CE
Mark”Directive(s) shall not be assumed.
Product Classification: Class I: Permanently connected, panel-mounted Industrial
Control Equipment with protective earthing (grounding). (EN61010-1).
Enclosure Rating: Panel-mounted equipment, IP 00. This controller must be
panel-mounted. Terminals must be enclosed within the panel. Front panel IP 65
(IEC 529).
Installation Category (Overvoltage Category): Category II: Energy-consuming
equipment supplied from the fixed installation, local level appliances, and
Industrial Control Equipment. (EN61010-1)
Pollution Degree: Pollution Degree 2: Normally non-conductive pollution with
occasional conductivity caused by condensation. (Ref. IEC 664-1)
EMC Classification: Group 1, Class A, ISM Equipment (EN55011, emissions),
Industrial Equipment (EN50082-2, immunity)
Method of EMC Assessment: Technical File (TF)
Declaration of Conformity: 51309602-000
Deviation from the installation conditions specified in this manual, and the
special conditions for CE conformity in Section 2.1, may invalidate this product’s
conformity with the Low Voltage and EMC Directives.

Installation
4/00 UDC2300 Universal Digital Controller User Manual 3
2 Installation
2.1 Overview
Introduction
Installation of the UDC 2300 consists of mounting and wiring the controller
according to the instructions given in this section. Read the pre-installation
information, check the model number interpretation (Appendix B), and become
familiar with your model selections, then proceed with installation.
2.2 Preliminary Checks
Introduction
Before you install the controller, remove the chassis and make any preliminary
checks necessary that are listed in Table 2-1. Figure 2-1 shows the locations for
jumper placements.
Table 2-1 Preliminary Checks
Check
Number Preliminary Check Description
1Input I Jumper Placement Check the internal jumper for INPUT 1 to make
sure it is set for the correct input type. The jumper
is located at position S101 on the printed wiring
board. Figure 2-1 shows the location of the jumper
and position selections.
2Optional Input 2 (RSP)
Jumper Placement Check the internal jumper for INPUT 2 to make sure it is set for the correct input type. The jumper
is located at position S201 on the printed wiring
board. Figure 2-1 shows the location of the jumper
and position selections.
3Control Relay 1 and Current
Output Check the internal jumper (W101) for CONTROL. The relay is shipped as N.O. (Normally Open).
Figure 2-1 shows the location of the jumper and
position selections.
See Table 2-2 for Control Relay contact
information.

Installation
4 UDC2300 Universal Digital Controller User Manual 4/00
Check
Number Preliminary Check Description
4Control Relay 2 and Alarm
Relay Action. The controller has been shipped with ALARM relays configured for N.C. (Normally Closed). If
you want to change to N.O. refer to Figure 2-1,
Jumper positions W201 and W202:
W201 is the ALARM RELAY 1 jumper.
W202 is the jumper for CONTROL RELAY #2 for
Duplex Output or 3 position step control and an
ALARM RELAY 2 for all others.
See Table 2-2 for Control Relay contact
information, and Table 2-3 for Alarm Relay
contact information.
See Alarm Relay Caution Note, Page 6.
Note: Solid State and open collector Outputs must have jumper set to
N.O. (Normally Open).
3 Position Step and Time Duplex must have Output 2-jumper (W202) set to
N.O (Normally Open).

Installation
4/00 UDC2300 Universal Digital Controller User Manual 5
Jumper Placements
W201
NO
NC
Alarm Relay #1
NC (default)
NO
NC
NO
W202
NO
NC
Output #2/
Alarm Relay #2
NC (default)
NO
NC
NO
W101
NO
NC
Output #1
NC
NO
NC
NO (Default)
S101 4 3 2 1
Input #1
Position 1: thermocouple (default)
Position 2: mV, Volt, RTD
Position 3: not used
Position 4:mA
No jumper: 0 -10 volts
Note: Jumpers enlarged for clarity
S201
W201
2 1
W202
NO
NC
NO
NC
S101 4 3 2 1
W101
NO
NC
Input #2
2 1
21
Volt
mA
Jumper
Position 2
S201
Jumper
Position 1
Main
Board
1
1. For Current Output use the N.O. position
Figure 2-1 Jumper Placements

Installation
6 UDC2300 Universal Digital Controller User Manual 4/00
2.3 Control and Alarm Relay Contact Information
Control Relays
ATTENTION
Control relays operate in the standard control mode (that is, energized when output
state is on).
Table 2-2 Control Relay Contact Information
Unit Power Control Relay
Wiring Control Relay Contact #1 or #2 Output Indicator Status
N.O. Open
Off
N.C. Closed
Off
N.O. Open
Closed Off
On
On
N.C. Closed
Open Off
On
Alarm Relays
ATTENTION
Alarm relays are designed to operate in a Failsafe mode (that is, de-energized during
alarm sate). This results in alarm actuation when power is OFF or when initially applied,
until the unit completes self-diagnostics. If power is lost to the unit, the alarms will
function.
Table 2-3 Alarm Relay Contact Information
Variable NOT in Alarm
State Variable in Alarm StateUnit Power Alarm Relay
Wiring Relay
Contact Indicators Relay Contact Indicators
N.O. Open Open
Off
N.C. Closed
Off
Closed
Off
N.O. Closed Open
On
N.C. Open
Off
Closed
On

Installation
4/00 UDC2300 Universal Digital Controller User Manual 7
2.4 Mounting
Physical Considerations
The controller can be mounted on either a vertical or tilted panel using the
mounting kit supplied. Adequate access space must be available at the back of
the panel for installation and servicing activities.
•The controller’s mounting enclosure must be grounded according to CSA
standard C22.2 No. 0.4 or Factory Mutual Class No. 3820 paragraph 6.1.5.
•The front panel is moisture rated NEMA 3/IP65 (IEC) when properly installed
with panel gasket.
Overall Dimensions
96
3.780
96
3.780
Panel Cutout
90 =0.0 +0.8
3.5906 +0.03
24
.945
Max Panel
Thickness 10
.394 Max (2)
4.19
105.4
.103
2.62 with optional
rear cover
90.7
3.57
21.0
.826
Dimensions:
Millimeters
Inches
20751
3.622 +0.031
-0.0
92 -0.0
+0.008
3.622 +0.031
-0.0
92 -0.0
+0.008
Figure 2-2 Mounting Dimensions (not to scale)

Installation
8 UDC2300 Universal Digital Controller User Manual 4/00
Mounting Method
Before mounting the controller, refer to the nameplate on the outside of the case
and make a note of the model number. It will help later when selecting the proper
wiring configuration.
Panel
20752
Figure 2-3 Mounting Method
Mounting Procedure
Table 2-4 Mounting Procedure
Step Action
1Mark and cut out the controller hole in the panel according to the dimension
information in Figure 2-2.
2Remove the screw cover and loosen the screw on the front of the controller.
Pull the chassis out of the case.
3Orient the case properly and slide it through the panel hole from the front.
4Remove the mounting kit from the shipping container and install the kit as
follows:
•Install the screws into the threaded holes of the clips.
•Insert the prongs of the clips into the two holes in the top and bottom of the
case.
•Tighten both screws to secure the case against the panel.
•Carefully slide the chassis assembly into the case, press to close, and
tighten the screw. Replace the screw cover.

Installation
4/00 UDC2300 Universal Digital Controller User Manual 9
2.5 Wiring
Electrical Considerations
he controller is considered “rack and panel mounted equipment”per EN61010-1,
afety Requirements for Electrical Equipment for Measurement, Control, and
aboratory Use, Part 1: General Requirements. Conformity with 72/23/EEC, the
ow Voltage Directive requires the user to provide adequate protection against a
hock hazard. The user shall install this controller in an enclosure that limits
PERATOR access to the rear terminals.
Mains Power Supply
This equipment is suitable for connection to 90 to 264 Vac, 50/60 Hz, power
supply mains. It is the user’s responsibility to provide a switch and non-time
delay (North America), quick-acting, high breaking capacity, Type F (Europe),
1/2A, 250V fuse(s), or circuit-breaker, as part of the installation. The switch or
circuit breaker shall be located in close proximity to the controller, within easy
reach of the OPERATOR. The switch or circuit breaker shall be marked as the
disconnecting device for the controller.
Controller Grounding
PROTECTIVE BONDING (grounding) of this controller and the enclosure in
which it is installed shall be in accordance with National and Local electrical
codes. To minimize electrical noise and transients that may adversely affect the
system, supplementary bonding of the controller enclosure to a local ground,
using a No. 12 (4 mm2) copper conductor, is recommended.
Control/Alarm Circuit Wiring
The insulation of wires connected to the Control/Alarm terminals shall be rated
for the highest voltage involved. Extra Low Voltage (ELV) wiring (input, current
output, and low voltage Control/Alarm circuits) shall be separated from
HAZARDOUS LIVE (>30 Vac, 42.4 Vpeak, or 60 Vdc) wiring per Permissible
Wiring Bundling, Table 2-5.
Electrical Noise Precautions
Electrical noise is composed of unabated electrical signals, which produce
undesirable effects in measurements and control circuits.
Digital equipment is especially sensitive to the effects of electrical noise. Your
controller has built-in circuits to reduce the effect of electrical noise from various
sources. If there is a need to further reduce these effects:
•Separate External Wiring—Separate connecting wires into bundles
(See Permissible Wiring Bundling - Table 2-5) and route the individual
bundles through separate conduit metal trays.

Installation
10 UDC2300 Universal Digital Controller User Manual 4/00
•Use Suppression Devices—For additional noise protection, you may want to
add suppression devices at the external source. Appropriate suppression
devices are commercially available.
ATTENTION
For additional noise information, refer to Document #51-52-05-01, How to Apply Digital
Instrumentation in Severe Electrical Noise Environments.
Permissible Wiring Bundling
Table 2-5 Permissible Wiring Bundling
Bundle No. Wire Functions
1•Line power wiring
•Earth ground wiring
•Control relay output wiring
•Line voltage alarm wiring
2Analog signal wire, such as:
•Input signal wire (thermocouple, 4 to 20 mA, etc.)
•4-20 mA output signal wiring
Digital input signals
3•Low voltage alarm relay output wiring
•Low voltage wiring to solid state type control circuits
Universal Output Functionality and Restrictions
Table 2-6 Universal Output Functionality and Restrictions
Output/Socket
Output Type Current
Output Relay #1 Relay #2 Relay #3 Auxiliary Output
Time Simplex 1 N/I Output 1 Alarm 2 Alarm 1 Not Needed
Time Simplex 2 N/A N/I Output 1 Alarm 1 Not Needed
Current Simplex Output N/I Alarm 2 Alarm 1 Not Needed
Time Duplex or
TPSC N/I Output 1 Output 2 Alarm 1 Not Needed
Current Dup. 100 % Output 1 N/I Alarm 2 Alarm 1 Not Needed
Current Dup. 50 % Output 1 N/I Alarm 2 Alarm 1 Output 2
Current/Time Output 1 N/I Output 2 Alarm 1 Not Needed
Timer/Current Output 2 N/I Output 1 Alarm 1 Not Needed
N/I = Not Installed
N/A = The output form or the individual output is Not Available or is not used for this output form.
Not Needed =Auxiliary Output is not needed to provide the desired output function and can be used for
another purpose. Auxiliary Output could also be used as a substitute for current Output 1.

Installation
4/00 UDC2300 Universal Digital Controller User Manual 11
2.6 Wiring the Controller
Using the information contained in the model number, select the appropriate
wiring diagrams from the composite wiring diagram below. Refer to the individual
diagrams listed to wire the controller according to your requirements.
Composite Wiring Diagram
Mains Power Supply
Input 1 Connections
Input 2 Connections
Relay Output
Electromechanical
Solid State
Open Collector
Current Output Connections
External Solid State Relay Output Option
Three Position Step Control Connections
Alarm and Duplex Output Connections
External Interface Option Connections
Transmitter Power for 4-20mA –2-Wire Transmitter
Using Open Collector Alarm 2 Output
Transmitter Power for 4-20mA –2-Wire Transmitter
Using Auxiliary Output
11
12
12
12
13
13
14
14
15
15
16
16
17
17
9
10
11
12
13
14
15
16
7
6
5
4
L2 / N
L1
8
Input Terminal
See Figure 2-6
Control Output
Terminals
See Note 1
Mains Power
Supply Terminals
See Figure 2-5 Input #2 Terminals
See Figure 2-7
External Interface
Options Terminals
See Figure 2-15
Alarm and
Duplex Output
Connections
See Figure 2-14
24855
Transmitter Power for
4-20 mA 2-wire
transmitters
• Using Alarm Output
See Figure 2-16
•Using Aux Output
See Figure 2-17
Time Proportional Electromechanical Relay Output –See Figure 2-8
Time Proportional Solid State Relay Output –See Figure 2-9
Time Proportional Open Collector Output –See Figure 2-10
Current Output –See Figure 2-11
External Solid State Relay Output –See Figure 2-12
Three Position Step Control Output –See Figure 2-13
NOTE1:
Figure 2-4 Composite Wiring Diagram

Installation
12 UDC2300 Universal Digital Controller User Manual 4/00
L2 / N
L1
Neutral
Mains
power
supply
Hot
Ground
1
2
24856
PROTECTIVE BONDING (grounding) of this controller
and the enclosure in which it is installed, shall be in
accordance with National and Local electrical codes. To
minimize electrical noise and transients that may
adversely affect the system, supplementary bonding of
the controller enclosure to a local ground, using a No.
12 (4 mm2) copper conductor, is recommended.
Before powering the controller, see “Preliminary
Checks”in this section of the user manual for
switch and jumper settings.
1
2Provide a switch and non-time delay (North America),
quick-acting, high breaking capacity, type F (Europe),
1/2 A, 250 V fuse(s), or circuit-breaker as part of the
installation.
Figure 2-5 Mains Power Supply
8
7
6R
+
-
mV, Volts (except 0-10V),
Milliamperes, orRadiamatic
Thermocouple
Platinum
RTD
24857
8
7
6R
+
-mV, Volt,
or
Milliampere
Source
8
7
6R
+
-
0 to 10 Volts
The voltage divider for 0 to 10
Volts is supplied with the
controller when the input is
specified. You must install it
when you wire the controller
before start-up. 1
Volt
Source
8
7
6
+
_
R
_
+1
2
3
1 These inputs are wired differently than the UDC2000
RTD1
Use
Thermocouple
extension wire
only
Figure 2-6 Input 1 Connections
15
16
+0 to 20 mA,
4 to 20 mA,
0 to 5 Volts
1 to 5 Volts
_
24858
See “Preliminary Checks”in this
section of the User Manual for
jumper selections.
Figure 2-7 Input 2 Connections