Honeywell SH-BLE-CT50 User manual

Bluetooth Low Energy Scan Handle
Models SH-BLE-CT50, SH-BLE-75e
Quick Start Guide
BTLE-SH-MULT-QS-01 Rev A
6/16
*CT50-ND-MULT-QS*
Out of the Box
Make sure that your shipping box contains these items:
• Bluetooth Low Energy (BLE) Scan Handle (SH-BLE-CT50 or
SH-BLE-75e)
• Quick Start Guide
If any of these items are missing or appear damaged, contact your Customer
Account Representative. Keep the original packaging in the event that you
need to return the scan handle for service or if you want to store it while not
in use.
The BLE scan handle was designed to allow access to all of the buttons and
the touch panel of the mobile computer. You can use the mobile computer
inserted into the scan handle with the Scan Handle Holster. If you need to set
the mobile computer inserted into the scan handle down on a flat surface,
you can place the combination nose down.
The scan handle can operate under all of the same environmental conditions
as the mobile computer. The operating temperature is -20 °C to 50 °C (-4 °F
to 122 °F).
Caution: We recommend the use of Honeywell accessories and power
adapters. Use of any non-Honeywell accessories or power adapters
may cause damage not covered by the warranty.
Mise en garde : Il est recommandé d'utiliser les périphériques, les
cordons d'alimentation et les adaptateurs secteur conçus par
Honeywell. L'utilisation de tout périphérique, cordon d'alimentation ou
adaptateur secteur d'une autre marque est susceptible de provoquer
des dommages non couverts par la garantie.
Download and Install the Scan Handle Tool
You can download the Scan Handle Tool from the Honeywellaidc website at
www.honeywellaidc.com.
Attach the Scan Handle to the CT50
No special tools are required to attach the scan handle to the computer.
• Slide the computer into the scan handle until it clicks firmly in place.
Attach the Scan Handle to the D75e
No special tools are required to attach the scan handle to the computer.
1. Press in on the rounded part of the release tabs on each side of the scan
handle base.
2. Slide the computer into the scan handle.
3. Press firmly on both sides of the scan handle locking bar to secure the
scan handle to the computer.
Scan a Bar Code with the Scan Handle
The scan handle makes it easy to scan a bar code with the computer. The
scan handle does not interfere with the ability to hear a beep on a good read.
• Pull on the handle trigger to scan a bar code.
Remove the Computer from the Scan Handle
If you need to replace the battery, you will need to remove the computer from
the scan handle:
• Press in on the bottom of both scan handle latches and slide the computer
out of the handle.
Replace the Scan Handle Batteries
There are two AA alkaline batteries in the scan handle that you will need to
change periodically.

Agency Information
USA
FCC ID: HD5-SH-BLE
FCC Part 15 Statement
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference
that may cause undesired operation.
FCC Interference Statement
This equipment has been tested and found to comply with the limits for a
Class B digital device pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio or television technician for
help.
RF Exposure
The equipment complies with FCC RF exposure limits set forth for an
uncontrolled environment. The equipment must not be co-located or
operating in conjunction with any other antenna or transmitter.
Note: Any changes or modifications made to this equipment not expressly
approved by Honeywell may void the FCC authorization to operate this
equipment.
Canada
Canadian Compliance
This ISM device complies with Canadian RSS-Gen Issue 4/RSS-247 Issue
1. Operation is subject to the following conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference
that may cause undesired operation.
Conformité à la règlementation canadienne
Cet appareil ISM est conforme à la norme CNR-Gen/CNR-247 du Canada.
Son fonctionnement est assujetti aux conditions suivantes :
1. Cet appareil ne doit pas causer de brouillage préjudiciable.
2. Cet appareil doit pouvoir accepter tout brouillage reçu, y compris le
brouillage pouvant causer un fonctionnement indésirable.
USA, Canada NRTL Statement
UL and C-UL Listed: UL60950-1 2nd Edition and CSA C22.2 No. 60950-1-07
2nd Edition.
CB Scheme
Certified to CB Scheme IEC 60950-1, Second Edition.
Europe
The CE marking indicates compliance with the following directives:
• 1995/5/EC R&TTE
• 2011/65/EU RoHS (Recast)
In addition, complies to 2006/95/EC Low Voltage Directive when used with
the recommended power source.
European contact:
Hand Held Products Europe B.V.
Lagelandseweg 70
6545CG Nijmegen
The Netherlands
Honeywell shall not be liable for use of our product with equipment (such as
power supplies, personal computers, and so on) that is not CE marked and
does not comply with the Low Voltage Directive.
Manufacture Contact Information:
Honeywell International Inc.
Honeywell Sensing & Productivity Solutions
9680 Old Bailes Road
Fort Mill, SC 29707 USA
Support
To search our knowledge base for a solution or log into the Technical Support
portal and report a problem, go to www.hsmcontactsupport.com.
User Documentation
For the user guide and other documentation, go to www.honeywellaidc.com.
Limited Warranty
For warranty information, go to www.honeywellaidc.com and click
Resources > Warranty.
Patents
For patent information, see www.hsmpats.com.
Disclaimer
Honeywell International Inc. (“HII”) reserves the right to make changes in
specifications and other information contained in this document without prior
notice, and the reader should in all cases consult HII to determine whether
any such changes have been made. The information in this publication does
not represent a commitment on the part of HII.
HII shall not be liable for technical or editorial errors or omissions contained
herein; nor for incidental or consequential damages resulting from the
furnishing, performance, or use of this material. HII disclaims all
responsibility for the selection and use of software and/or hardware to
achieve intended results.
This document contains proprietary information that is protected by
copyright. All rights are reserved. No part of this document may be
photocopied, reproduced, or translated into another language without the
prior written consent of HII.
Copyright © 2016 Honeywell International Inc. All rights reserved.