Honeywell XENON 1902G-BF User manual

Xenon™ 1902G-BF
CCB01-010BT-BF
Battery-Free Wireless Area-Imaging Scanner and 
Charge Base
Quick Start Guide
Rev C
2/17

Note: Refer to your user’s guide for information about cleaning
your device.
Getting Started
Turn off the computer’s power before connecting the base, then
power up the computer once the base is fully connected. When
the base is connected and powered up, put the scanner in the
base to establish a link. The green LED on the base flashes to
indicate the scanner’s instant charge pack is charging. The
scanner must be returned to the base when not in use. A scan-
ner charged on the base with the power supply for 35 seconds
will result in 100 scans, with one scan every second.
Power Supply Assembly (if included)
Note: The power supply must be ordered separately, if needed.

Connecting the Scanner
USB:
Note: If you are charging the scanner using the USB cable, the
current available for charging is reduced and charge times
are increased. Charging via the power supply is faster.

Keyboard Wedge:
RS232 Serial Port:

RS485:
LED Sequences and Meaning
When charging, the base indicates the progress while the scan-
ner resides in the base.
Base Button/LED Charge Level Approximate
Expected Scans*
Green on 100% 450
Green slow blink 50-99% 200
Green fast blink 30-50% 100
Yellow fast blink 0-30% Charging - do not
scan

The following feedback is provided by the scanner when the
scanner is out of the base and has been idle for 5 seconds.
* The number of scans was measured with a clearly printed UPC code in
good light. The approximate number of scans varies with changes in
label quality, symbology, and environmental factors.
Reading Techniques
The view finder projects an aim-
ing beam that should be centered
over the bar code, but it can be
positioned in any direction for a
good read.
Hold the scanner over the bar
code, pull the trigger, and center
the aiming beam on the bar code.
The aiming beam is smaller when
the scanner is closer to the code
and larger when it is farther from the code. Hold the scanner
close to smaller bar codes, and farther away from large bar
codes to get a proper read.
Scanner LED Scanner Beep Charge
Level
Approximate
Expected
Scans*
Yellow 
3 sets of flashes
2 short beeps per
flash
30% 100
Red 
3 sets of flashes
2 short beeps per
flash
10% 50

If the bar code is highly reflective (e.g., laminated), you may need
to tilt the scanner at an angle so the bar code can be scanned.
Note: If the scanner beeps 3 times when scanning a bar code, the
link has not been established. If the scanner beeps once,
the link has been established.
Standard Product Defaults
The following bar code resets all standard product default set-
tings.
RS485 Interface
The RS485 interface defaults to port 5B. If you have an IBM POS
terminal using port 9B, scan the appropriate code below to pro-
gram the terminal, then power cycle the cash register.
Note: For additional RS485 interface selections, see the User’s
Guide for your product at our website,
www.honeywellaidc.com.
Standard Product
IBM Port 9B HHBCR-1
Interface
IBM Port 9B HHBCR-2
Interface

USB Serial
Scan the following code to program the scanner to emulate a
regular RS232-based COM Port. If you are using a Microsoft®
Windows® PC, you will need to download a driver from the Hon-
eywell website (www.honeywellaidc.com). The driver will use the
next available COM Port number. Apple® Macintosh computers
recognize the scanner as a USB CDC class device and automati-
cally use a class driver.
Note: No extra configuration (e.g., baud rate) is necessary.
USB PC Keyboard
Scan the following code to program the scanner for a USB PC
Keyboard.
Keyboard Country
Scan the Program Keyboard Country bar code below, then scan
the numeric bar code(s) from page 2, then the Save bar code to
program the keyboard for your country. As a general rule, the
following characters are not supported by the scanner for coun-
tries other than the United States:
@ | $ # { } [ ] = / ‘ \ < > ~
USB Serial
USB PC Keyboard
Program Keyboard Country

Note: For a complete list of country codes, see the User’s Guide
for your product at our website, www.honeywellaidc.com.
Locked Link
If you link a scanner to a base using the Locked Link Mode,
other scanners are blocked from being linked if they are inad-
vertently placed into the base. If you do place a different scan-
ner into the base, it will charge the scanner, but the scanner will
not be linked.
Country Code Scan Country Code Scan
Arabia 91 Korea 93
Belgium 1 Portugal 13
China 92 Russia 26
France 3 Spain 10
Germany/Austria 4 Sweden/Finland 2
Great Britain 7 Switzerland 6
Hungary 19 Thailand 94
IBM Financial 90 Turkey (Q) 24
Italy 5 USA (Default) 0
Japan 28 Vietnam 95
Save
Locked Link Mode
(Single Scanner)

To use a different scanner, you need to unlink the original scan-
ner by scanning the Unlink Scanner bar code.
Override Locked Scanner
If you need to replace a broken or lost scanner that is linked to a
base, scan the Override Locked Scanner bar code with a new
scanner, and place that scanner in the base. The locked link will
be overridden; the broken or lost scanner’s link with the base will
be removed, and the new scanner will be linked.
Unlinking the Scanner
If the base has a scanner linked to it, that scanner must be
unlinked before a new scanner can be linked. Once the previous
scanner is unlinked, it will no longer communicate with the
base. Scan the Unlink Scanner bar code to unlink a scanner.
Override Locked Scanner
Unlink Scanner