Honeywell 3 inch dome camera User manual

Document 800-00789 – Rev C – 07/08
3 Inch Dome Camera
Quick Install Guide
FCC Compliance Statement
Information to the User: This equipment has been tested and found to comply with the limits for a
Class B digital device. Pursuant to Part 15 of the FCC Rules, these limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one of the following
measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected
• Consult the dealer or a radio/TV technician for help.
Caution Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This Class B digital apparatus complies with Canadian ICES-003.
Manufacturer’s Declaration of Conformance
The manufacturer declares that the equipment supplied with this guide is compliant with the essential
protection requirements of the EMC directive 89/336/EEC and the Low Voltage Directive LVD 73/23
EEC, conforming to the requirements of standards EN 55022 for emissions.
12345678
tnemtsujdAaremaCgnitnuoMaremaCnoitaraperP
2. Connect the wiringSurface Mount
Optional Camera Settings
1 2 3
1. Remove the dome cover
3. Prepare the mounting surface (surface orflush mount)
a. Gentlyturn the dome covercounter-
clockwiseto unlock, then pull free of
the housing.
b. Gentlypull the innerlinerfree of the
two notches in the housing.
c. Setthe dome and lineraside.
a. Connectthe video output
connector.
b. Connectthe 24 VAC/12 VDC power
connector.
24VAC/12 VDC powerconnector
Videooutput connector
4S Electrical JunctionBox
a. Adapterplate(optional). Secure to
electricalbox using appropriate screws
(notsupplied).
b. Securecamera base to ceiling orwall.
Adapterplate
(optional)
Electricalbox (not
supplied)
Base
a. Markthe holes.
b. Insertscrew anchors into
holes.
Flush Mount
a. Adapterplate(optional forceiling tile).
Secure using appropriate screws (not
supplied).
Surfacemount: Secure skirt to ceiling orwall
using_______ screws supplied.
b. Securecamera base with ______________
screws,supplied.
Skirt
Adapterplate
(optional)
a. Turnthe Axis ring in the desired
direction,then ret ighten.
b. Turnthe Zoom leverslightly
counter-clockwiseto loosen.
Thenrotate arou nd the lens for
thedesired image view.
c. Turnthe Focus levercounter-
clockwiseto loosen. Rotate to
adjustforthe best picture
quality.
d. Retightenthe Zoom and Focus
leversto lock them after
makingadjustments.
Do not turn the lens more than360°.
Do not use excessive force to loosen
the levers and axis ring.
Axis
ring
Focus
lever
Zoom
lever
Note Pleaseuse the supplied DC Iris and Line Lock adjustment tool to adjust pictur
e
brightnessand phase adjustment.
PictureBrightness Use the LEVEL screw to compensate forthe iris level. L (low) darkens
t
picture.H (high) brightens the picture.
PhaseAdjustmentUse t he V Phase Adjustment Pot to adjust the phase difference betwe
e
cameras.Make sure Switch 4 is ON to activate the Line lock function (
A
operationonly).
DIPSwitches
Monitorout
Modesetting
DIPswitches
Switch Function
1BLC(Backlight Compensation). ON = camera automatically
adjuststhe exposure. OFF = factory default.
2AGC(Automatic Gain Control). ON = camera adjusts forlow
lightconditions. ON = factory default.
3DC/AESMode. Leave in ON position only.
4LL(Line Lock). Set the camera synchronization to internal or
Linelock (only available with 24 VAC). ON= factory default.
Aftermounting and adjusting
the camera, attach the dome
cover:
a. Attachthe innerlinerto the base until
thelinerclicks into place.
b. Alignthe dome coverwith the three
dometabs on the unit.
c. Turnthe dome gently clockwise until it
locksinto place.
Preparation
Camera Mounting
Camera Adjustment
Installation Completion
1
2
3
4
Contents
Fully assembled camera
Hardware kit
Mounting template
This guide
Operating Notes
Warnings (where applicable to your locale)
Installation and servicing should be performed only by qualified and experienced technicians
to conform to all local codes and to maintain your warranty.
WARNING! The use of CSA Certified/UL Listed Class 2 power adapters is required to
ensure compliance with electrical safety standards.
WEEE (Waste Electrical and Electronic Equipment). Correct disposal of this product
(applicable in the European Union and other European countries with separate collection
systems). This product should be disposed of, at the end of its useful life, as per applicable local
laws, regulations, and procedures.
Power Supply This dome camera can operate on 24 VAC or 12 VDC.
Operating Conditions Avoid:
• Viewing bright objects (for example, light fixtures) for extended
periods
• Operating or storing the unit in the following locations.
• Extremely humid, dusty, hot/cold environments (where the
operating temperature is outside the recommended range of
14°F to 122°F [-10°C to +50°C])
• Close to sources of powerful electromagnetic radiation, such
as radio or TV transmitters
• Close to fluorescent lamps or objects reflecting light
• Under unstable light sources (may cause flickering)
Product Dimensions Contact Information
4.9”(124.6 mm)
4.9”(124.6 mm)
4.17”(106.1 mm)
1.8” (46.0 mm)
www.honeywellvideo.com
+1.800.796.CCTV (North America only)
[email protected]
Document 800-00789 – Rev C – 07/08
© 2008 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without
written permission from Honeywell Video Systems. The information in this publication is believed to be accurate in all
respects. However, Honeywell Video Systems cannot assume responsibility for any consequences resulting from the use
thereof. The information contained herein is subject to change without notice. Revisions or new editions to this publication
may be issued to incorporate such changes.
2.03” (51.75 mm)
∅3.97”
(101 mm)
3.0”(76.2 mm)
0.9” (23.0 mm)
3.37”(85.5 mm)
1.68”
(42.8 mm)

1234 567 8
Preparation Camera Mounting Camera Adjustment
3. Connect the Wiring
Surface Mount
Optional Camera Settings
1 2 3
1. Remove the Dome Cover
2. Prepare the Mounting Surface (Surface or Flush Mount)
a. Gently turn the dome cover counter-
clockwise to unlock, then pull free of
the housing. If required, loosen the
security screw first.
b. Gently pull the inner liner free of the
two notches in the housing.
c. Set the dome and liner aside.
a. Connect the video output
connector.
b. Connect the 24 VAC/12 VDC power
connector.
24 VAC/12 VDC power connector
Video output connector
4S Electrical Junction Box
a. Secure the adapter plate to the
electrical box using appropriate
screws (not supplied).
b. If necessary, tuck Video/Power and
BNC cabling into notch.
c. Secure camera base to ceiling or wall
with 3 screws, supplied.
Adapter plate
Electrical box
(not supplied)
Base
Use camera base or mounting
template to:
a. Mark the holes as
required.
b. Insert screw anchors into
holes.
Flush Mount
a. Surface mount: Secure skirt to ceiling or wall
using appropriate screws, not supplied.
b. If necessary, tuck Video/Power and BNC
cabling into notch.
c. Surface mount: Secure camera base with M3
screws, supplied.
Flush mount: Secure camera base with
appropriate M3 screws, not supplied.
Skirt
Adapter plate
Legend
A = Tilt rotation
B = Horizontal rotation*
C = Pan rotation
.
Picture Brightness The LEVEL screw compensates for the iris level. L (low) darkens the
picture. H (high) brightens the picture.
Phase Adjustment The V Phase Adjustment Pot adjusts the phase difference between
cameras. Switch 7 must be ON to activate Line lock (AC only).
DIP Switches
(Refer to your
camera model)
Default settings are
shown in bold.
SW HighRes+TDN High Res Std Res
1DC/AES DC/AES DC/AES
2AWB/ATW AWB/ATW AWB/ATW
3BLC ON/OFF BLC ON/OFF BLC ON/OFF
4AGC ON/OFF AGC ON/OFF AGC ON/OFF
5TDN Not used FLK
6FLK ON/OFF FLK ON/OFF LL ON/OFF
7LL ON/OFF LL ON/OFF Not available
8Not used Not used Not available
Mode setting
DIP switches
After ➋ mounting and ➌
adjusting the camera, attach the
dome cover:
a. Attach the inner liner to the base until
the liner clicks into place.
b. Align the dome cover with the three
dome tabs on the unit.
c. Turn the dome gently clockwise until it
locks into place.
d. If desired, secure the dome to the base
with the security screw (see picture).
= ON
= OFF
Monitor out
V-Phase
Level
+–
HL
Notch
Notch
Notch
Zoom lever
(bottom)
Focus lever
(top)
Security
screw B
C
A
* If necessary, loosen the screw
that locks the gimbal assembly in
place, before adjusting the
camera.
Setscrew
Base
Base
Screws
(not supplied)
M3 screws
(not supplied)
M3 screws
(supplied)
Screws
(not supplied)
Screws
(supplied)