Honeywell HD31H(X) User manual

1
Performance Series Camera
User Guide
Document 800-18605 – Rev A – 06/2014
HD30H(X)
HD31H(X)
HD40H(X)

2 HD40H(X)/HD30H(X)/HD31H(X) Camera User Guide
800-18605 – Rev A – 06/2014
Thank you for purchasing our product. If there are any questions, or
requests, please do not hesitate to contact the dealer.
This manual applies to HD40H(X), HD30H(X) and HD31H(X) cameras.
The information in this publication is believed to be accurate in all respects.
However, Honeywell cannot assume responsibility for any consequences
resulting from the use thereof. The information contained herein is subject
to change without notice. Revisions or new editions to this publication may
be issued to incorporate such changes.
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.

3 HD40H(X)/HD30H(X)/HD31H(X) Camera User Guide
800-18605 – Rev A – 06/2014
NOTE: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la Classe B est conforme à la norme NMB-003
du Canada.
EU Conformity Statement
This product and - if applicable - the supplied
accessories comply with the applicable harmonized
European standards listed under the Low Voltage
Directive 2006/95/EC, the EMC Directive 2004/108/EC, the RoHS
Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with
this symbol cannot be disposed of as unsorted municipal
waste in the European Union. For proper recycling,
return this product to your local supplier upon the
purchase of equivalent new equipment, or dispose of it at designated
collection points. For more information see: www.recyclethis.info.
Safety Instructions
These instructions are intended to ensure that users can use the product
correctly to avoid danger or property loss.
The precautions are divided into “Warnings” and “Cautions”.
Warnings: Serious injury or death may occur if any of the warnings are
neglected.
Cautions: Injury or equipment damage may occur if any of the cautions
are neglected.

4 HD40H(X)/HD30H(X)/HD31H(X) Camera User Guide
800-18605 – Rev A – 06/2014
Warnings
WARNING: Installation and servicing should be performed only by qualified
and experienced technicians to conform to all local codes and to maintain
your warranty.
WARNING: This device is configured for 12 V DC operation only. Do not
connect to a higher voltage. Use only with NRTL approved Class 2 or LPS
power supplies. To prevent potential ground loop issues, a separate PSU
should be used for each camera.A multiple-output PSU may be used if the
multiple output PSU has isolated and protected (2 Amax) outputs.
Cautions
CAUTION: The light emitted from the near-infrared light emitting diodes
(LEDs) provides illumination over a wide area. This light is not considered
a risk to the unshielded human eye. However, as with any light source, it is
recommended that normal precautions be taken to avoid unnecessary
Warnings Follow these
safeguards to prevent
serious injury or death.
Cautions Follow these
precautions to prevent potential
injury or material damage.

5 HD40H(X)/HD30H(X)/HD31H(X) Camera User Guide
800-18605 – Rev A – 06/2014
exposure. For example, avoid staring into the beam or viewing the LEDs
directly with optical instruments at close range.
Important Safety Instructions
Read and keep these instructions.
Ensure that your installation area can safely support 3 times the weight
of the camera.
Do not install the camera in extreme temperature conditions. Only use
the camera where temperatures are within the limits shown in the
camera specifications. Be especially careful to provide ventilation
when operating under high temperatures.
Do not install indoor rated cameras where they will be exposed to rain
or moisture.
To prevent damage to the imager, do not aim the camera toward an
extreme light source.
Do not touch the camera lens, dome or bezel (front glass plate).
Do not drop the camera or subject it to physical shock.
Do not use strong or abrasive cleaners, clean only with a soft cloth and
mild detergent or alcohol.
Do not open the camera or attempt to service it yourself. Refer all
service issues to your dealer.

6 HD40H(X)/HD30H(X)/HD31H(X) Camera User Guide
800-18605 – Rev A – 06/2014
Table of Contents
Introduction..................................................................................................... 7
Product Features................................................................................ 7
Overview............................................................................................. 8
Installation..................................................................................................... 10
Ceiling/Wall Mounting for HD40H(X) Camera............................... 10
Ceiling/Wall Mounting for HD30H(X) Camera............................... 13
Ceiling/Wall Mounting for HD31H(X) Camera............................... 16
Power Supply.................................................................................... 20

7 HD40H(X)/HD30H(X)/HD31H(X) Camera User Guide
800-18605 – Rev A – 06/2014
Introduction
Product Features
This series of camera adopts a new generation imaging sensor with high
sensitivity and advanced circuit design technology. It features high
resolution, low image distortion, and low noise, which makes it ideal for
surveillance systems and image processing systems.
High-performance sensor supplies high resolution high-quality images
IR LEDs enables day/night surveillance (HD30H and HD31H)
Day/night automatic switching
ATW provides high color rendition
Automatic electronic shutter control to adapt to the different
surveillance environments
Automatic gain control, with adaptive brightness
High SNR provides high-quality image
Ingress protection: IP66-rated (HD30H and HD31H)
Notes: HD40H(X) camera does not support day/night auto switching and
IP66 ingress protection.

8 HD40H(X)/HD30H(X)/HD31H(X) Camera User Guide
800-18605 – Rev A – 06/2014
Overview
Figure 1-1 Overview of HD40H(X) Camera
Figure 1-2 Overview of HD30H(X) Camera
Power
Cable Video
Cable
Lower
Dome
Black Liner
Camera
Lock Screw
Enclosure
Mounting
Base
Camera
Power Cable
Video Cable

9 HD40H(X)/HD30H(X)/HD31H(X) Camera User Guide
800-18605 – Rev A – 06/2014
Figure 1-3 Overview of HD31H(X) Camera
Enclosure
Trim Ring
Camera
Lock Screw
Video Cable
Power Cable
Zoom & Focus

10 HD40H(X)/HD30H(X)/HD31H(X) Camera User Guide
800-18605 – Rev A – 06/2014
Installation
Before you start:
•Make sure that the camera is in good condition and all of the assembly
parts are included.
•Make sure that all related equipment is powered-off during the
installation.
•Check that the camera specification agrees with the installation
environment.
•To avoid damage, ensure the power supply voltage matches your
camera requirements.
•If the product does not function properly, please contact your dealer or
the nearest service center. Do not disassemble the camera for repair
or maintenance by yourself.
•Make sure that the installation surface is strong enough to withstand
three times the weight of the camera.
Ceiling/Wall Mounting for HD40H(X) Camera
Steps:
1. Hold the mounting base, and rotate the lower dome counterclockwise
to disassemble the lower dome and the black liner (see Figure 1-5).
2. Drill the screw holes and the cable hole in the ceiling/wall according to
the supplied mounting template.