Honeywell HD3DH User manual

Document 800-20540V1 – Rev A – 06/2015
Configuration Guide
960H Series Fixed
Mini Dome Camera
HD3DH HD3DHX
HD3HRH HD3HRHX
HD4D3H HD4D3HX
HD4DIRH HD4DIRHX

2
Revisions
Issue Date Revisions
A 06/2015 Updated from 800-20540. Corrected some Specifications,
including temperatures, minimum illumination, AES range,
power consumption, and construction materials.

3
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Configuring the Camera. . . . . . . . . . . . . . . . . . . . . . . . . . 5
Exposure Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Color Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Day&Night Menu . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Function Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Motion Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Privacy Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Exit Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

4
Introduction
This document describes how to configure the camera settings for the following Honeywell
960H Series cameras:
•HD3DH(X) High Resolution, VFAI Lens, True Day/Night, Indoor, Mini Dome
•HD3HRH(X) High Resolution, VFAI Lens, Day/Night, Indoor/Outdoor, Mini Dome
•HD4D3H(X) High Resolution, VFAI Lens, True Day/Night, Rugged Indoor/Outdoor,
Mini Dome
•HD4HIRH(X) High Resolution, VFAI Lens, True Day/Night, Rugged Indoor/Outdoor,
IR Mini Dome
These instructions are intended for system installers, administrators, and operators. For
information about installing the camera, please to the Quick Installation Guide for your
camera.

5
Configuring the Camera
The camera is configured using the on-screen display (OSD) menus. You can connect a
portable monitor during installation using the supplied adapter cable.
To display the OSD main menu, press the
OSD controller joystick located on the
camera control board.
Move the joystick up or down to navigate
through the menu options. Move the joystick
right to change a menu setting.
When a menu option or setting is followed by
, press the joystick to access the next
screen. To go back to the main menu, select
RETURNor EXIT JUMP and then press the
joystick.
UP
DOWN
RIGHTLEFT

6
The camera has the following OSD menu structure:
1. EXPOSURE
LENS: MANUAL/DC
BACKLIGHT: OFF/BLC/HME
WDR/DEFOG: OFF/WDR/
DEFOG
AGC: 0 to 20
SENSE-UP: OFF/×2 to ×512
3D DNR: OFF/LOW/MID/HIGH
2. COLOR
WB BAL.:ATW/MANUAL/
PUSHLOCK
COLOR GAIN: 0 to 20
3. DAY&NIGHT
D&N MODE: AUTO/COLOR/
B&W
CONTROL: AUTO/EXTERN
DELAY: 0 to 15
B/W BURST: OFF/ON
SMART IR: ANTI-SAT/SAT.
AREA
4. FUNCTION
MIRROR: OFF/ON
SHARPNESS: 0 to 20
GAMMA: 0.35 to 0.70
POSI/NEGA: POSI/NEGA
SLC: 0 to 20
5. MOTION
MOTION: OFF/ON
SENSITIV.: 1 to 30
MOTION SET: AREA NO./
AREA USE/TOP/BOTTOM/
LEFT/RIGHT
6. PRIVACY
COLOR: BLACK/GRAY-1/
GRAY-2/GRAY-4/WHITE/
YELLOW/GREEN/BLUE/RED/
CYAN/MAGENTA
PRIVACY SET: AREA SET/
DISPLAY/TOP/BOTTOM/
LEFT/RIGHT/RET/INI.
7. SETUP
CAMERA TITLE: OFF/ON
SYNC: INT/LINE LOCK
COMMUNICA: CAM ID/ID
DISP./BAUDRATE/
PROTOCOL/UTC
LANGUAGE: ENGLISH
FONT COLOR: BLUE/GREEN/
CYAN/RED/MAGENTA/
YELLOW/BLACK/GRAY
SPECIAL.: O.L.P.F/DPC
8. EXIT
SAVE
RESTORE
EXIT

7
Exposure Menu
LENS
Note Only DC mode is supported at this time.
Choosing MANUAL mode may cause the camera
to operate incorrectly.
1. Select DC.
2. Set the BRIGHTNESS (0–20). The higher
the number, the brighter the image will
appear.
3. Set the SHUTTER speed (1/60–1/120000).
Note The SENSE-UP menu cannot be
controlled if the SHUTTER setting is
above 1/60.
4. Set FLC to ON or OFF. Setting FLC to ON
prevents image flickering.
5. Set FOCUS SET to the highest value for a
clear image.

8
BACKLIGHT
Backlight Compensation (BLC) prevents subjects in defined areas of the scene from
appearing too dark when backlighting is present. Highlight Masking Exposure (HME)
masks bright areas of the scene to allow objects to appear clearly.
BACKLIGHT is set to OFF by default. To enable this feature, select BLC or HME.
If BLC is selected:
1. Set LEVEL to LOW, MIDDLE, or HIGH.
2. Set DISPLAY to ON or OFF to show or hide
the BLC mask.
3. If DISPLAY is set to ON, adjust the values
for TOP, BOTTOM, LEFT, and RIGHT to
set the size and position of the BLC mask.
4. Set RET/INI. to RETURN or INITIAL.
• Select RETURN to go back to the main
menu.
• Select INITIAL to reset the settings to
the factory defaults.
If HME is selected:
•SetLEVEL to LOW, MIDDLE, or HIGH.

9
WDR/DEFOG
1. WDR/DEFOG is set to OFF by default. To enable this feature, select D-WDR or
DEFOG.
2. Set D-WDR or DEFOG to AUTO or MANUAL.
•IfAUTO is selected, the WDR or DEFOG level is set automatically based on the
environment.
•IfMANUAL is selected, set LEVEL to LOW, MIDDLE, or HIGH.
3. Set MODE to ONLY DAY or ALL DAY.
•IfONLY DAY is selected, WDR or DEFOG is enabled during the day only.
•IfALL DAY is selected, WDR or DEFOG is enabled during daytime and
nighttime.
AGC
Auto Gain Control (AGC) enhances the picture brightness in low-light conditions, but also
increases picture noise.
Set AGC (0–20).

10
SENSE-UP
Note The SENSE-UP menu cannot be controlled if the SHUTTER setting is
above 1/60.
Sense-Up automatically activates slow shutter function when a scene is too dark.
Set SENSE-UP to OFF or to a value from×2 to ×512. Selecting a value over ×4 is not
recommended as it may cause the image to lag.
3D DNR
3D Digital Noise Reduction (3D DNR) improves image clarity in low-light conditions.
Set 3D DNR to OFF, LOW, MID, or HIGH.