Horizon Hobby FORCE MH-35 User manual

Instruction Manual | Bedienungsanleitung | Manuel d’utilisation | Manuale di istruzioni
Note: Attempting to fly the helicopter without completely reading the manual may cause injury to yourself and people in
the vicinity, as well as damage to the helicopter.
Hinweis: Der Versuch, den Helikopter zu fliegen, ohne das Handbuch vollständig zu lesen, kann Verletzungen an Ihnen
selbst und Menschen in der Nähe, wie auch Schäden am Helikopter verursachen.
A noter: tenter de faire voler l’hélicoptère sans avoir lu l’intégralité du manuel peut provoquer des blessures (à vous-
même et aux personnes alentour) ainsi que des dégâts à l’hélicoptère.
Nota: Un tentativo di far volare l’elicottero senza aver letto completamente il manuale può avere come risultato una
lesione del manovratore e delle persone circostanti, nonchè danni all’elicottero stesso.
TM
MH-35 or FHX FORCE helicopter and transmitter
Hélicoptère MH-35 ou FHX FORCE et émetteur
Elicottero e trasmittente MH-35 o FHX FORCE
MH 35 oder FHX FORCE Hubschrauber und Sender

2
WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product
before operating. Failure to operate the product correctly can result in damage to the product, personal
property and cause serious injury.
This is a sophisticated hobby product. It must be operated with caution and common sense and requires some
basic mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or
damage to the product or other property. This product is not intended for use by children without direct adult
supervision. Do not attempt disassembly, use with incompatible components or augment product in any way
without the approval of Horizon Hobby, Inc.This manual contains instructions for safety, operation and maintenance.
It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in
order to operate correctly and avoid damage or serious injury.
NOTICE
All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon
Hobby, Inc. For up-to-date product literature, visit horizonhobby.com and click on the support tab for this product.
Meaning of Special Language
The following terms are used throughout the product literature to indicate various levels of potential harm when
operating this product:
NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little
or no possibility of injury.
CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a
possibility of serious injury.
WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral
damage, and serious injury OR create a high probability of superficial injury.
Warning
An RC helicopter is not a toy! If misused, it can cause serious bodily harm and damage to property. Fly only in open
areas, preferably at approved flying sites, following all instructions.
Keep items that can get entangled in the rotor blades away from the main and tail blades, including loose clothing,
pencils and screwdrivers. Especially keep your hands away from the rotor blades.
Additional Safety Precautions and Warnings
Age Recommendation: 14 years or over. Not a toy. Not intended for use by children without direct
adult supervision.
As the user of this product, you are solely responsible for operating it in a manner that does not endanger yourself
and others or result in damage to the product or the property of others.
This model is controlled by a radio signal that is subject to interference from many sources outside your control.
This interference can cause momentary loss of control so it is advisable to always keep a safe distance in all
directions around your model, as this margin will help to avoid collisions or injury.
Never operate your model with low transmitter batteries.•
Always operate your model in open spaces away from full-size vehicles, traffic and people.•
Carefully follow the directions and warnings for this and any optional support equipment (chargers,• rechargeable battery packs, etc.).
Keep all chemicals, small parts and anything electrical out of the reach of children.•
Moisture causes damage to electronics.• Avoid water exposure to all equipment not specifically designed and protected for this purpose.
Never lick or place any portion of your model in your mouth as it could cause serious injury or even death.•
Never operate
vehicle with
damaged wiring.
Never touch
moving parts.
Always keep
parts dry.
Always
keep moving
parts clean.
Always let parts
cool after use
before touching.

3
Product Registration .........................3
BoxContents ..............................3
Battery Warnings and Guidelines................4
Installing the Transmitter Batteries . . . . . . . . . . . . . . 4
Battery Charging............................4
Installing the Flight Battery ....................4
Flying your FORCE Helicopter . . . . . . . . . . . . . . . . . . 5
Transmitter Control Identification . . . . . . . . . . . . . . . 6
Flying the Helicopter.........................6
Restore Transmitter to Factory Settings...........7
VDAS ....................................7
FORCE Operations Setup Mode.................8
Advanced Swashplate Settings .................9
Installing Optional 150mAh Flight Battery . . . . . . . . . 9
Re-Binding your FORCE helicopter . . . . . . . . . . . . . . 9
Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . 10
ReplacementParts.........................10
Warranty and Repair Policy ...................11
FCCStatement............................12
Compliance Information for the European Union . . . 12
Table of Contents
In order to provide the best possible product, some parts may vary slightly from those shown.
Product Registration
Please register your product at www.force-rc.com.
Box Contents
Box contents will vary, depending on which helicopter you’ve purchased.
FHX
MH-35

4
Battery Warnings and Guidelines
Installing the Transmitter Batteries
3
4
1
26
7
5
Battery Charging
Install Discharged
Flight Battery Flashing When Charged Remove Charged
Flight Battery
Solid While Charging
Make Sure Flight Battery is Charging
Install Discharged
Flight Battery Flashing When Charged Remove Charged
Flight Battery
Solid While Charging
Make Sure Flight Battery is Charging
Install Discharged
Flight Battery Flashing When Charged Remove Charged
Flight Battery
Solid While Charging
Make Sure Flight Battery is Charging
Solid LED while charging
Flashing LED when charging is almost complete
No LED when charging is complete
Note: When transmitter charging LED continues to flash after flight
battery is removed, replace transmitter batteries. When charging a
flight battery requires longer than 20 minutes, transmitter batteries
may require replacement.
An optional flight battery charger, Celectra 4-Port Charger with AC Adapter
Combo (EFLC1004AC) is available from www.horizonhobby.com.
Installing the Flight Battery
Note: Keep helicopter still
after connecting flight
battery to let helicopter
gyroscope calibrate. Make
sure the throttle control
stick is fully lowered for 3
seconds to arm the throttle
for flight. Throttle trim may
need to set at neutral or
lower.
Align red dots and
push helicopter
connector on
flight battery.
Once LED goes solid,
install flight battery
in battery cradle.
13
2
Do not move
for 5 –10 seconds
Always use a
charger compatible
with batteries.
Always charge
Batteries away from
flammable materials.
Never Alter
Batteries.
Never charge
damaged Batteries.
Never touch or
use hot Batteries.
120F/49C
Never leave
charging Batteries
unattended.
Always remove
batteries
after use.
Always remove
batteries before
disassembly.
Note: A flight battery may be charged in the transmitter’s charging
port while the transmitter is in use.

5
Flying your FORCE helicopter
If you are not accustomed to the controls of your FORCE heli, familiarize yourself with them before attempting your
first flight. To learn more about advanced flying techniques, visit www.force-rc.com.
Transmitter Mode Legend MODE 2 MODE 1
Climb Descend
Nose Turns Left
Forward
This movement is disabled in SimpliFly™ mode
Backward
Right
Left
Nose Turns Right

6
Transmitter Control Identification
Mode 2/Mode 1
Note: When pressed down, trim but-
tons make a sound that increases or
decreases in pitch at each pressing.
The middle or neutral trim position uses
a middle-range tone. A series of beeps
sounds end of control range.
Rudder Trim
Rudder Trim
Throttle Trim
Elevator Trim
Aileron Trim
Aileron Trim
Elevator Trim
Throttle Trim
ON/OFF
Switch
Rudder/Elevator
Rudder/Throttle
Aileron/Throttle
Aileron/Elevator Fire Buttons
Mode Switch
You can convert your Mode 1 transmitter to Mode 3 or Mode 2 transmitter to Mode 4. The Mode Switch allows you to
change the Aileron and Rudder between right and left flight control sticks for mode change. For more information on
Modes 3 and 4, please visit www.force-rc.com.
Rear of Transmitter
Flying the helicopter
Note: Learn about more advanced flying on the product page for the FORCE helis on www.force-rc.com to see many of
these maneuvers and adjustments performed by the helicopter and pilot.
1. Throttle must be at the lowest setting for 3 seconds to arm ESC.
2. Increase throttle until helicopter rises 1 foot (30cm) above floor.
3. Adjust throttle so the helicopter stays at this height.
4. When helicopter does not stay in one place, you may need to push trim buttons to adjust controls. Always land the
helicopter and make trim adjustments when the helicopter is not easy to control.
a) When helicopter drifts forward or backward, adjust elevator trim using buttons by elevator control stick. For
example, when helicopter drifts forward, increase back elevator trim.
b) When helicopter drifts left or right, adjust aileron trim. For example, when helicopter drifts left, increase right
aileron trim.
c) When helicopter spins left or right, adjust rudder trim. For example, when there is leftward spin, increase right
rudder trim.
Always keep
vehicle in sight
and under control.
Always
decrease throttle at
rotor strike.
Always keep transmitter
powered on while
vehicle is powered.

7
VDAS Visual Damage Assessment System
Helicopter spins once.
Team LED flashes
for 2 seconds.
Helicopter spins
once, then spins back.
Team LED flashes
for 2 seconds.
Helicopter spins continuously with
decreased throttle power until it is
on the floor. Team LED flashes for
10 seconds. Hit count is reset for
return to flying.
Aim at opponent’s
hit detector mounted
behind heli gun barrel
Hit #1
Hit #3
Hit #2
Please fly your helicopter, do tests of firing, team color, shot range and the response to hits (VDAS) before going
head-to-head in battle.
Hold your powered helicopters and see if there is a reaction (blinking white LED at Team color LED) when helicop-
ters fire on each other.
Helicopter spins once.
Team LED flashes
for 2 seconds.
Helicopter spins
once, then spins back.
Team LED flashes
for 2 seconds.
Helicopter spins continuously with
decreased throttle power until it is
on the floor. Team LED flashes for
10 seconds. Hit count is reset for
return to flying.
Aim at opponent’s
hit detector mounted
behind heli gun barrel
Hit #1
Hit #3
Hit #2
Get to within 10 feet (3m) of oppo-
nent with short range, and 20 feet
(6m) with long range. Aim at oppon-
tent’s hit detector mounted behind
heli gun barrel.
Note: Distance from the opponent and bright sunlight may interfere with shooting and helicopter response to
shots. Go to www.force-rc.com for battle tactics and tips.
Note: DO NOT use elevator and aileron controls at Hit #3 response or the helicopter may not land safely on
its landing gear. Rudder and throttle controls may used at Hit #3 response.
When firing,
team color LED
blinks white twice.
Target volume is a long egg shape
Press and release either
button to fire at targets
1 second of
weapons
fire sound
Note : 1 second
between shots.
When firing,
team color LED
blinks white twice.
Target volume is a long egg shape
Press and release either
button to fire at targets
1 second of
weapons
fire sound
Note : 1 second
between shots.
Restore Transmitter to Factory Settings
Press and hold down two trim buttons (see illustration)
while pushing power switch to ON. Hold trim buttons
8 seconds. Release trim buttons when tone sounds,
indicating transmitter has been restored to factory
settings. Only transmitter settings are reset with this
procedure. See FORCE Operations Setup Mode instruc-
tions for changing helicopter settings such as shot
range and team color.
Release buttons
when tone sounds.
Hold down 2 trim buttons.
Push Power Switch to ON.2
1
Hold for
8 seconds

8
FORCE Operations Setup Mode
Press and Release Right Fire
Button to change Range
Green LED: Accepts any hits.
Blue LED: Accepts hits only from
Red and Green teams.
Red LED: Accepts hits only from
Blue and Green teams.
Press and Release Left Fire
Button to change Team Color
Push stick down into case
until it clicks
SimpliFly: 2 beeps at stick push.
Transmitter LED blinks.
Standard: 1 beep at stick push.
LED solid light.
LED
Beeps
Low: Up to 10-foot (3m) range
LED blinks slowly
High: Up to 20-foot (6m) range
LED blinks rapidly
Range Limit Function
Press and Release Right Fire
Button to change Range
Green LED: Accepts any hits.
Blue LED: Accepts hits only from
Red and Green teams.
Red LED: Accepts hits only from
Blue and Green teams.
Press and Release Left Fire
Button to change Team Color
Push stick down into case
until it clicks
SimpliFly: 2 beeps at stick push.
Transmitter LED blinks.
Standard: 1 beep at stick push.
LED solid light.
LED
Beeps
Low: Up to 10-foot (3m) range
LED blinks slowly
High: Up to 20-foot (6m) range
LED blinks rapidly
Team ID Function
Press and Release Right Fire
Button to change Range
Green LED: Accepts any hits.
Blue LED: Accepts hits only from
Red and Green teams.
Red LED: Accepts hits only from
Blue and Green teams.
Press and Release Left Fire
Button to change Team Color
Push stick down into case
until it clicks
SimpliFly: 2 beeps at stick push.
Transmitter LED blinks.
Standard: 1 beep at stick push.
LED solid light.
LED
Beeps
Low: Up to 10-foot (3m) range
LED blinks slowly
High: Up to 20-foot (6m) range
LED blinks rapidly
SimpliFly Mode
2Connect Flight Battery.
1Push Left Control to Full.
Before ESC arms (5 seconds),
Press and hold Left Fire Button and
push Transmitter switch ON.
3
Push Left
Control Stick
to Low.
To Save settings
and Exit Setup Mode
4Helicopter: slow, double blinking
blue LED
Transmitter: continuous gunfire sound,
blinking LED
Hold Fire for
8 Seconds
2Connect Flight Battery.
1Push Left Control to Full.
Before ESC arms (5 seconds),
Press and hold Left Fire Button and
push Transmitter switch ON.
3
Push Left
Control Stick
to Low.
To Save settings
and Exit Setup Mode
4Helicopter: slow, double blinking
blue LED
Transmitter: continuous gunfire sound,
blinking LED
Hold Fire for
8 Seconds
Note: If heli LED is
blinking rapidly after
step 3, unplug the flight
battery and try again.
Save and Exit
Default: Long Range Default: Green Default: SimpliFly disabled
Your helicopter is ready for battle when you open the box. Factory settings are standard flight (not SimpliFly), Green
team (rogue or free-for-all), and long range (20 feet (6m)). Only when you want to change these battle settings is
FORCE Operations Setup Mode required.

9
More information is available at www.force-rc.
com for advanced settings and adjustments for
your FORCE helicopter and transmitter.
The FORCE helicopter comes with an adjustable
swashplate for advanced pilots. Move lower rotor
head links from the shorter to the longer set of
inner swashplate control balls (see illustration).
This change provides increased helicopter re-
sponse for flying against drafts or air movement.
Note: Always attach links to control balls opposite
each other.
Advanced Swashplate Settings
ST1.2 x 5 (1)
EFLH2401 ST1.2 x 5 (2)
M0.8 x 2.5 (4)
M1.2 x 2.5 (2) M1.2 x 2.5 (2)
M1.2 x 1.8 (2)
M1.2 x 1.8 (3)
M0.8 x 2.5 (8) M1.2 x 2.5 (2)
ST1.2 x 5 (7)
ST1.2 x 5 (2)
ST1.2 x 5 (2)
ST1.2 x 5 (5)
EFLH2409 EFLH2410 EFLH2418
EFLH2219B EFLH2427
EFLH2404 EFLH2416
EFLH2412
EFLH1066 EFLH2421
EFLH2420 EFLH2211 EFLH2213
EFLH2214 EFLH2215
EFLH3021
EFLHB1501S
EFLH2225 EFLH1067
EFLB1201S
EFLH2217 EFLH2222
EFLH2424
Short Swashplate Control Balls
Anti-rotation
pin
Long Swashplate Control Balls
The transmitter and helicopter in the box are bound together at the factory. Re-binding is for transferring helicopter
control between transmitters or restoration after accidental loss of binding.
Re-Binding your FORCE Helicopter
1
5
234
Fully Charged
OFF
ON
A
B
68
Flashes
10 Flashes
Solid
10 Beeps
Flashes
7
Wait
5 seconds
5–10
seconds
Installing Optional 150mAh Flight Battery
Before installing an optional
150mAh flight battery, install short
tubing on the battery. This will
keep installation of this battery
(longer than the 120mAh battery)
from interfering with flight opera-
tion.
12
150mAh Battery
Do not move for
5-10 seconds
3

10
Some issues may be not addressed in this short guide. Please refer to more FORCE information
at www.force-rc.com.
Problem Possible Cause Possible Solution
Gun does not seem to fire •DamagetoIRCombatUnit •ReplaceIRIRCombatUnit
Helicopter does not respond to fire
from opponent
•Battleconditionsinterfere
•DamagetoIRCombatUnit
•DoacheckofIRCombatUnitrange
settings, decrease lighting in room,
etc.
•ReplaceIRIRCombatUnit
Aircraft will not respond to throttle
but other controls function
•Throttleandthrottletrimnot
lowered at aircraft initializing.
•Yourtransmitterthrottlechannel
might be set to the wrong direc-
tion.
•Lowerthrottlestickandthrottle
trim to lowest settings to arm
throttle correctly.
•Restoretransmittertofactoryset-
tings
Charger light on transmitter stays
on after Li-Po battery is discon-
nected or remains on for longer
than 40 minutes when charging.
•Transmitterbatterieshavelow
charge
•ReplaceAAbatteriesinthetrans-
mitter
Aircraft has bad cyclic control
reactions (for example, forward
elevator input results in aircraft
flying sideways left or right)
•Swashplateanti-rotationpinis
out of the main frame bracket
•Carefullyputpinofswashplatein
the bracket channel, high at the
back of the main frame
Transmitter control stick blocked
or “sticky”
•Stickgimbalmovedupintrans-
mitter
•Disconnectightbatteryfrom5-in-
1 unit, power off the transmitter
and push in the transmitter control
stick until it clicks
Troubleshooting Guide
Replacement Parts
For replacement and optional parts to keep your helicopter battle-ready, go to www.force-rc.
com

11
Warranty and Repair Policy
Warranty Period: Exclusive Warranty- Horizon Hobby,
Inc., (Horizon) warranties that the Products purchased
(the “Product”) will be free from defects in materials and
workmanship at the date of purchase by the Purchaser.
Limited Warranty: Horizon reserves the right to change
or modify this warranty without notice and disclaims
all other warranties, express or implied.
(a) This warranty is limited to the original Purchaser
(“Purchaser”) and is not transferable. REPAIR OR RE-
PLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE
EXCLUSIVE REMEDY OF THE PURCHASER. This warranty
covers only those Products purchased from an authorized
Horizon dealer. Third party transactions are not covered by
this warranty. Proof of purchase is required for all warranty
claims.
(b) Limitations- HORIZON MAKES NO WARRANTY OR
REPRESENTATION, EXPRESS OR IMPLIED, ABOUT NON-
INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE OF THE PRODUCT. THE PURCHASER
ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED
THAT THE PRODUCT WILL SUITABLY MEET THE REQUIRE-
MENTS OF THE PURCHASER’S INTENDED USE.
(c) Purchaser Remedy- Horizon’s sole obligation hereunder
shall be that Horizon will, at its option, (i) repair or (ii)
replace, any Product determined by Horizon to be defec-
tive. In the event of a defect, these are the Purchaser’s
exclusive remedies. Horizon reserves the right to inspect
any and all equipment involved in a warranty claim. Repair
or replacement decisions are at the sole discretion of
Horizon. This warranty does not cover cosmetic damage
or damage due to acts of God, accident, misuse, abuse,
negligence, commercial use, or modification of or to any
part of the Product. This warranty does not cover damage
due to improper installation, operation, maintenance, or
attempted repair by anyone other than Horizon. Return of
any Product by Purchaser must be approved in writing by
Horizon before shipment.
Damage Limits: HORIZON SHALL NOT BE LIABLE FOR
SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES, LOSS
OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN
ANY WAY CONNECTED WITH THE PRODUCT, WHETHER
SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLI-
GENCE, OR STRICT LIABILITY. Further, in no event shall the
liability of Horizon exceed the individual price of the Prod-
uct on which liability is asserted. As Horizon has no control
over use, setup, final assembly, modification or misuse, no
liability shall be assumed nor accepted for any resulting
damage or injury. By the act of use, setup or assembly, the
user accepts all resulting liability.
If you as the Purchaser or user are not prepared to accept
the liability associated with the use of this Product, you
are advised to return this Product immediately in new and
unused condition to the place of purchase.
Law: These Terms are governed by Illinois law (without
regard to conflict of law principals).
WARRANTY SERVICES
Questions, Assistance, and Repairs: Your local hobby
store and/or place of purchase cannot provide war-
ranty support or repair. Once assembly, setup or use of
the Product has been started, you must contact Horizon
directly. This will enable Horizon to better answer your
questions and service you in the event that you may need
any assistance. For questions or assistance, please direct
your email to [e-mail], or call
877.504.0233 toll free to speak to a Product Support rep-
resentative. You may also find information on our website
at www.horizonhobby.com.
Inspection or Repairs: If this Product needs to be
inspected or repaired, please use the Horizon Online
Repair Request submission process found on our website
or call Horizon to obtain a Return Merchandise Authoriza-
tion (RMA) number. Pack the Product securely using a
shipping carton. Please note that original boxes may be
included, but are not designed to withstand the rigors of
shipping without additional protection. Ship via a carrier
that provides tracking and insurance for lost or damaged
parcels, as Horizon is not responsible for merchandise
until it arrives and is accepted at our facility. An Online Re-
pair Request is available at www.horizonhobby.com under
the Repairs tab. If you do not have internet access, please
contact Horizon Product Support to obtain a RMA number
along with instructions for submitting your product for
repair. When calling Horizon, you will be asked to provide
your complete name, street address, email address and
phone number where you can be reached during business
hours. When sending product into Horizon, please include
your RMA number, a list of the included items, and a brief
summary of the problem. A copy of your original sales
receipt must be included for warranty consideration. Be
sure your name, address, and RMA number are clearly
written on the outside of the shipping carton.
Notice: Do not ship batteries to Horizon. If you have
any issue with a battery, please contact the
appropriate Horizon Product Support office.
Warranty Inspection and Repairs: To receive warranty
service, you must include your original sales receipt
verifying the proof-of-purchase date. Provided warranty
conditions have been met, your Product will be repaired or
replaced free of charge. Repair or replacement decisions
are at the sole discretion of Horizon.
Non-Warranty Repairs: Should your repair not be
covered by warranty the repair will be completed and
payment will be required without notification or esti-
mate of the expense unless the expense exceeds 50%
of the retail purchase cost. By submitting the item for
repair you are agreeing to payment of the repair without
notification. Repair estimates are available upon request.
You must include this request with your repair. Non-war-
ranty repair estimates will be billed a minimum of ½ hour
of labor. In addition you will be billed for return freight.
Horizon accepts money orders and cashiers checks, as
well as Visa, MasterCard, American Express, and Discover
cards. By submitting any item to Horizon for inspection or
repair, you are agreeing to Horizon’s Terms and Conditions
found on our website under the Repairs tab.

12
Country of
Purchase
Horizon Hobby Address Phone Number/ Email
United States
Horizon Service Center
(Electronics and engines)
Horizon Product Support
(All other products)
4105 Fieldstone Rd
Champaign, Illinois
61822 USA
877-504-0233
[e-mail]
United Kingdom Horizon Hobby Limited Units 1-4 Ployters Rd
Staple Tye
Harlow, Essex
CM18 7NS, United Kingdom
[phone]
[e-mail]
Germany Horizon Technischer Service Hamburger Str. 10
25335 Elmshorn
Germany
[phone]
[e-mail]
France Horizon Hobby SAS 14 Rue Gustave Eiffel
Zone d’Activité du Réveil Matin
91230 Montgeron
[phone]
FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Caution: Changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
This product contains a radio transmitter with wireless technology which has been tested and found to be
compliant with the applicable regulations governing a radio transmitter in the 2.400GHz to 2.4835GHz frequency
range.
Compliance Information for the European Union
Declaration of Conformity (in accordance with ISO/IEC 17050-1)
No. HH20100806
Product(s): FORCE MH-35 Heli RTF, FORCE MH-35 Heli RTF Mode 1,
FORCE FHX Heli RTF, FORCE FHX Heli RTF Mode 1
Item Number(s): FCE2000, FCE2000M1, FCE2100, FCE2100M1
Equipment Class: 1
The object of declaration described above is in conformity with the requirements of the specifications listed below,
following the provisions of the European R&TTE directive 1999/5/EC:
EN 300-328 Technical requirements for Radio equipment.
EN 301 489 General EMC requirements
EN 60950 Safety
Steven A. Hall
Vice President
International Operations and Risk Management
Horizon Hobby, Inc.
Signed for and on behalf of:
Horizon Hobby, Inc.
Champaign, IL USA
Aug 06, 2010
This product must not be disposed of with other waste. Instead, it is the user’s responsibility
to dispose of their waste equipment by handing it over to a designated collection point for the
recycling of waste electrical and electronic equipment. The separate collection and recycling
of your waste equipment at the time of disposal will help to conserve natural resources and
ensure that it is recycled in a manner that protects human health and the environment. For more
information about where you can drop off your waste equipment for recycling, please contact
your local city office, your household waste disposal service or where you purchased the product.
Instructions for Disposal of WEEE by Users in the European Union

©2010 FORCE® is an exclusive brand of Horizon Hobby, Inc.
All marks are trademarks or registered trademarks of Horizon Hobby, Inc.
US 7,391,320. US D578,146. PRC ZL 200720069025.2. Other patents pending.
The Spektrum trademark is used with permission of Bachmann Industries, Inc.
Printed 7/10 27966