horsch LEEB 12 TD User manual

TRANSLATION OF THE ORIGINAL OPERATING INSTRUCTIONS
READ CAREFULLY PRIOR TO STARTING UP!
KEEP OPERATING INSTRUCTIONS IN A SAFE PLACE!
ART.:
ISSUE:
OPERATING INSTRUCTIONS
ART.:
08/2020
LEEB 12 TD
60015262

- Translation of the Original Operating Instructions -
Machine Identication
The corresponding data is to be entered into the list below upon
receiving the machine:
Serial number: ..................................................
Machine type: ...................................................
Year of construction: ........................................
Initial installation: ..............................................
Fittings: .............................................................
..........................................................................
..........................................................................
..........................................................................
Publication date of Operation Manual:
Latest change:
Address of Retailer: Name: ......................................................................
Road: ......................................................................
Town/City: ......................................................................
Tel.: ......................................................................
Customer No.:
Retailer: ......................................................................
Address of HORSCH: HORSCH Maschinen GmbH
92421 Schwandorf, Sitzenhof 1
92401 Schwandorf, Postbox 1038
Tel.: [phone] / 7143-0
Fax: [phone]
E-mail: [email protected]
Customer No.:
HORSCH: ......................................................................
Conrmation of receipt of machinery
Warranty claims become only e󰘯ective when the 󰘰rst use of the machine is reported to HORSCH
Maschinen GmbH within a week.
At www.horsch.com under SERVICE PARTNERBEREICH an interactive PDF form is available for down-
load for this purpose (not available in all languages).
By clicking on Send – depending on the email program installed – a mail draft with the completed
form is generated automatically. Alternatively, the form can be sent as email attachment to machine.
[email protected].
A di󰘯erent form of registration (postal mail, by fax, etc.) is not allowed for.
08/2020 60015262 Leeb 12 TD en

EG-Konformitätserklärung
Die
HORSCH LEEB Application Systems GmbH
Kleegartenstraße 54, D-94405 Landau a. d. Isar
erklärt hiermit in alleiniger Verantwortung als Hersteller, dass das nachfolgend genannte Produkt:
Typ:
den einschlägigen grundlegenden Sicherheits- und Gesundheitsanforderungen der Richtlinien 2006/42/EG
und 2009/127/EG entspricht.
Landau, 31.01.2020 Klaus Winkler
Dokumentationsbevollmächtigter
HORSCH Maschinen GmbH
Sitzenhof 1
D-92421 Schwandorf
_________________________
Theodor Leeb
Geschäftsführer
Gezogene Pflanzenschutzspritze
Leeb 12 TD
Translation of EC Declaration of Conformity
(Directive 2006/42/EC)
The manufacturer HORSCH LEEB Application Systems GmbH
Kleegartenstraße 21
D-94405 Landau a. d. Isar
hereby declares that the product
Type:
this declaration refers to, conforms with all relevant fundamental health and safety requirements of the
directive 2006/42/EC and 2009/127/EC.
Landau, 31/01/2020 Klaus Winkler
Theodor Leeb
Managing director
Pulled crop protection sprayer
Leeb 12 TD
Documentation Representative
HORSCH Maschinen GmbH
Sitzenhof 1
D-92421 Schwandorf

Table of contents
Introduction...................................................6
Foreword ........................................................6
Notes on representation .................................6
Service............................................................7
Warranty claim processing .............................7
Consequential damage...................................7
Safety and responsibility.............................8
Intended use...................................................8
Qualication of personnel...............................9
Children in danger ........................................10
Personal protective outt..............................10
Safety in tra󰀩c..............................................10
Safety in operation........................................ 11
Crop protection agents and liquid fertiliser .... 15
Environmental protection..............................16
Retrotting and conversions.........................16
Care and maintenance .................................16
Danger zone.................................................18
Safety stickers ..............................................19
Commissioning...........................................24
Delivery.........................................................24
Transport ......................................................24
Installation ....................................................24
Initial commissioning of the service
brake system ................................................25
Initial commissioning of the suspension .......25
Adjusting the hydraulic system on
the hydraulic valve block ..............................26
Assemble the wheels....................................26
Technical data...............................................27
Dimensions................................................29
Permissible total weight and tyres .............30
Noise development data...............................33
Required tractor equipment..........................33
Design..........................................................35
Overview.......................................................35
Hydraulics.....................................................36
Safety and protective features......................37
Fluid circuit - Construction elements
on machines of the CCS Pro variant ............38
Two-tank system with variant CCS Pro ........39
Supply lines between tractor and machine.... 39
Tra󰀩c compliant equipment..........................40
Instruction stickers........................................42
Components................................................43
Drawbar and connecting...............................43
Hydraulic support..........................................43
Shut-o󰀨 valve (only for machines
with passive follow-up steering)....................44
Hydraulics lockout switch .............................44
Steering ........................................................45
Vehicle version passive follow-up steering..... 45
Vehicle variant Active steering of
both axles (option) .....................................46
Adjusting the mechanical steering
end stop.....................................................47
Trailing control on hillside locations
via manual control ........................................47
Hydropneumatic suspension ........................48
Brake system................................................49
Automatic load dependent brake
pressure regulator (ALB) ...........................50
Connection of brake system ......................51
Uncoupling the brake system ....................52
Spraying mixture container...........................52
Fresh water tank...........................................53
Access steps..............................................54
Platform .....................................................54
Dome............................................................55
Hand washing tank.......................................55
Spraying pump .............................................56
Piston diaphragm pump ...............................57
Illuviation valve ............................................57
Stainless steel induction hopper................59
CCS - Continuous inside cleaning................60
External cleaning system (option) ................60
Agitator .........................................................61
Filter..............................................................62
Control unit ...................................................64
Main control terminal ....................................64
2

Multi-function handle ....................................65
Default assignment multi-function handle... 66
Transport, document and safety container ... 67
Document roll ...............................................67
Lifting points .................................................68
Folding boom................................................69
Folding variants – folding boom....................70
BoomControl..............................................72
Transport lock ............................................73
Collision protection ....................................75
Spraying line..............................................76
Nozzle body...............................................77
Optional equipment....................................80
Hydraulic connections ..................................80
Coupling hydraulic hoses...........................80
Uncoupling hydraulic hoses.......................80
PTO-shaft pump (optional) ...........................81
Hydraulic compressor (optional)...................82
GPS receiver (optional) ................................85
Camera (optional).........................................87
Wind meter (optional) ...................................87
Edge and border nozzles..............................88
SectionBox (optional) ................................89
NightLight (optional) .....................................90
Automatic Tyre Pressure Control (ATP)
(optional).......................................................91
Pack storage (optional).................................92
Operation.....................................................93
Commissioning / Tractor change..................93
Connecting/Parking ......................................93
Connecting ...................................................94
Transport position.........................................95
Parking .........................................................96
Manoeuvring the uncoupled machine........96
Folding the folding boom ..............................97
Unfolding....................................................98
Folding.......................................................98
Preparation for spraying operation ...............99
Calculating lling / rell quantities............101
Filling table for residual areas..................102
Filling the spraying mixture container
through the lling port ..............................104
Direct lling / External lling (optional).....104
Filling via the lling dome........................105
Filling the fresh water tank through
the lling port ..........................................105
Illuviation of preparations............................106
Illuviation valve ........................................106
Flushing in liquid preparations during
the lling process on machines of the
CCS Pro variant.......................................107
Flushing in liquid preparations for full
or partly lled spraying mixture
container on machines of the
CCS Pro variant.......................................108
Illuviation of powdery preparations
and carbonyl diamide on machines
of the CCS Pro variant.............................109
Pre-cleaning the canister with
spraying mixture ......................................109
Canister cleaning with fresh water........... 110
Spraying operation ..................................... 110
Special notes for spraying operation ....... 110
Folding boom control ............................... 111
Spraying pressure, nozzle size,
placing quantity, travel speed, agitator .... 111
Spraying................................................... 112
Measures for windward drift reduction .... 113
Spraying with 25 cm nozzle spacing
and reduced target area distance ........... 113
Draining the spraying mixture
container via the pressure output ............ 113
Faults.......................................................... 115
Nozzle selection....................................... 116
3

Residual quantities .....................................122
Technical residual quantities....................122
Draining o󰀨 technical residual quantities .... 122
Draining of technical residual quantities
on machines of the CCS Pro variant .......122
Diluted residual quantity ..........................123
Draining the fresh water tank...................123
Cleaning .....................................................124
CCS - Continuous inside cleaning
(Continuous Cleaning System)................125
Cleaning the lter.....................................126
Cleaning the sprayer with the tank
empty ......................................................127
Cleaning the sprayer with the tank lled ... 128
Folding boom cleaning with
“Air Valve” (option) ...................................129
Changing the track width............................130
Care and maintenance .............................131
Maintenance overview................................134
Ball-and-socket coupling ............................136
Lubrication instructions...............................139
Overview of lubrication points
basic machine..........................................141
Overview of lubrication points
middle section..........................................143
Overview of folding boom
lubrication points......................................145
Maintenance of brake system.....................149
General visual inspection.........................149
Inspection of brake lining.........................150
Brake adjustment.....................................150
Air vessel .................................................150
Test instructions for dual line
service brake system (workshop work)....151
Maintenance of axle ...................................151
Checking the bearing play of the
wheel hub (workshop work).....................151
Check the wheel hub bearing
clearance (workshop work)......................152
Replacing the grease of the wheel
hub bearing..............................................152
Axle adjustment (workshop work)............154
Maintenance of the hydraulic system .........155
Inspection criteria for hydraulic hoses .....156
Assembly and disassembly of
hydraulic hoses........................................156
Replacing the pressure lter of the
hydraulic system......................................157
Calibrating the ow meter...........................157
Wheels and tyres........................................158
Changing wheels........................................158
Autonomous hydraulic system (optional)....160
PTO-shaft pump oil change.....................160
Inspection of the crop protection sprayer ...160
Pump capacity test ..................................160
Flow meter test ........................................161
Storage ......................................................162
At the end of the season.............................162
Drain...........................................................162
Draining the spraying mixture container ... 162
Draining the fresh water tank...................162
Putting the sprayer system into
winter storage.............................................163
Before the new season...............................164
Waste disposal .........................................166
Appendix ...................................................167
Tightening torque........................................167
HORSCH Leeb metering cup .....................169
Determining the placing quantity in l/ha.... 169
Nozzle selection and control....................169
Liquid fertiliser operation ............................170
Index ..........................................................172
4

5

Introduction
Foreword
We would like to thank you for the trust you
have expressed in us by buying this machine.
Congratulations for having purchased a quality
product from HORSCH.
Before commissioning the machine, read and
strictly comply with the operating instructions. In
doing so, you will avoid accidents, reduce repair
costs and downtime and increase the reliability
and service life of your machine. Pay attention
to the safety notes!
HORSCH will not assume liability for any dam-
age or malfunctions resulting from failure of
complying with the operating instructions.
These operating instructions will assist you in
getting to know your machine and using it cor-
rectly for its intended purposes.
The operating instructions must be read and
strictly adhered to by all persons working on or
with the machine e.g.:
• Operation (including preparation, fault recti󰘰-
cation during work, care)
• Maintenance (maintenance, inspection)
• Transport
Trained personnel of our service and sales
partners will instruct you in the operation and
care of your machine. By submitting the ac-
knowledgement of receipt you have con󰘰rmed
proper acceptance of the machine.
The warranty period starts with the date of
delivery.
The operating instructions were prepared based
on the EC Machinery Directive, EN Standards
and German laws and regulations. The national
laws and regulations must be observed when
using the machine. National laws and regula-
tions supersede the information of the operating
instructions!
We reserve the right to alter illustrations as well
as technical data and weights contained in these
operating instructions for the purpose of improv-
ing the machine.
The illustrations in these operating instructions
show di󰘯erent versions of the implement and
di󰘯erent equipment variants.
Because of technical progress, the instructions
may contain illustrations that do no longer cor-
respond to the current series status.
Notes on representation
Warning notes
These operating instructions distinguish be-
tween three di󰘯erent types of warning notes.
The following signal words with warning sym-
bols are used:
DANGER
Highlights a danger that will lead to death or
severe injury if it is not avoided.
WARNING
Highlights a danger that may lead to death or
severe injury if not avoided.
CAUTION
Highlights a danger that can lead to injury if not
avoided.
Please read the warning notes given in these
operating instructions!
6

Instructions
NOTE
Identi󰘰es important notes.
Take-action instructions are indicated by arrow
points:
¾...
¾Keep the order of the instructions. Alternatively,
instructions may be numbered consecutively.
The designations right, left, front and rear apply as
seen in travel direction.
Service
HORSCH Company would like you to be com-
pletely satisfied with your machine and our
services.
If you encounter any problems, please feel free
to contact your sales partner.
The service sta󰘯 of our sales partners and the
service employees at HORSCH will always be
available to assist you.
In order to be able to solve technical problems
as quickly as possible, we ask you kindly to
support us.
Please help the service personnel by providing
the following information to avoid unnecessary
queries.
• Customer number
• Name of customer representative
• Name and address
• Machine model and serial number
• Purchasing date and operating hours or area
performance
• Type of problem
Warranty claim
processing
Warranty claim forms must be submitted to
HORSCH through your local HORSCH sales
partner.
Consequential damage
The machine has been manufactured by
HORSCH with greatest care. However, despite
the intended use deviations in placing quantity
up to total failure may be caused by e.g.:
• damage caused by external in󰘱uences
• wear of wear items
• missing or damaged tools
• incorrect travel speeds
• incorrect setting of the unit (incorrect connec-
tion, non-observance of setting tables)
• failure to comply with the operating instruc-
tions
• blockages or seed bridging
• neglect and improper care and maintenance
Therefore, it is crucial to always check your ma-
chine before and during use for correct operation
and adequate application accuracy.
Compensation claims for damages that have
not occurred on the machine are excluded. This
also means that any liability for consequential
damages caused by travel and operating faults
is excluded.
7

Safety and
responsibility
The following warnings and safety notes apply
to all sections in these operating instructions.
The machine has been built in accordance with
latest technical standards and generally ac-
cepted safety regulations. However, risks for
life and limb of the operator or third parties and
impairment of the machine or other material as-
sets can occur during use.
Please read and comply with the following safety
notes, before you start to use the machine!
Intended use
The machine is intended for the application of
󰘱uids on agricultural areas. The application of
crop protection agents and liquid fertilizers (AHL)
on agricultural land is particularly important. The
machine can be used to mix, dose and transport
the biocatalyst to be placed on the application
area.
The intended use also includes taking note of
and observing the notes and instructions given
in these operating instructions, observing all
pictograms and warnings on the machine, ob-
serving all maintenance and repair intervals and
complying with the de󰘰ned technical limits and
areas of application.
When participating with the machine in public
road tra󰘲c, the respective national registration
and tra󰘲c law must also be complied with.
The permissible axle and drawbar loads must
not be exceeded during road travel.
Any other kind of use of the machine contradict-
ing the above, especially
• connecting/attachment to an agricultural trac-
tor that is not suitable
• 󰘰lling the machine with 󰘱ammable 󰘱uids other
than those approved in the scope of the op-
erating instructions
• exceeding the permissible technical total
weight
• operating the machine while persons are still
in the danger zone (this includes in particular
transport rides on the machine)
• carrying out maintenance and/or repair work
on a machine that has not been shut down or
is not secured against restarting
are considered not as intended.
Horsch does not assume any liability for dam-
ages resulting from the unintended use of the
machine.
Spare parts
Genuine spare parts and accessories from
HORSCH have been specially designed for this
machine.
Spare parts and accessories which are not de-
livered by us have not been tested or approved
by us.
Installation or use of non-original HORSCH
products may have a detrimental effect on
speci󰘰c design features of the machine and
impair the safety of machine operators and the
machine itself.
HORSCH will not assume liability whatsoever for
damage resulting from the use of non-original
parts and accessories.
If the component to be replaced is marked with
a safety sticker, these stickers must also be
ordered and attached to the spare part.
8

Operating Instructions
The operating instructions are a part of the
machine!
Failure to comply with the operating instruc-
tions can result in severe or even fatal physical
injuries.
¾Read and follow the corresponding sections
in the operating instructions before starting
work.
¾Store the operating instructions and keep for
future use.
¾Pass the operating instructions on to a later
user.
Qualication of personnel
Unintended use of the machine can lead to se-
vere or even fatal physical injuries. In order to
prevent accidents, each person involved in work
with the machine must meet the following general
minimum requirements:
¾The person must be physically able to keep
the machine under control.
¾The person is able to perform work with the
machine safely within the scope of these op-
erating instructions.
¾The person is acquainted with the function of
the machine within the scope of its work and
is able to assess and avoid any work related
dangers. The person is able to recognize and
avoid work related dangers.
¾The person has understood the operating
instructions and is able to implement the in-
formation given in the operating instructions
accordingly.
¾The person is fully familiar with the safe opera-
tion of the vehicle.
¾The person knows all applicable road tra󰘲c
regulations and is in possession of a valid
driving permit for road travel.
¾A person being instructed must only work with
or on the machine under the supervision of
an experienced person.
The owner of the machine must
¾regulate the area of responsibility, compe-
tence and monitoring of personnel.
¾if necessary train and instruct the personnel.
¾make the operating instructions accessible for
the machine operator.
¾ensure that the operator has read and fully
understood the operating instructions.
Groups of operators
Persons who work with the machine must have
been trained for the di󰘯erent activities involved.
Instructed operators
These persons must have been trained for
their respective activities by the owner or other
quali󰘰ed experts. This refers to the following
activities:
• Road transportation
• Application and set-up work
• Operation
• Maintenance
• Troubleshooting and repair
Operators trained by HORSCH
Furthermore, for certain activities the corre-
sponding personnel must have been trained by
service personnel from HORSCH. This refers to
the following activities:
• Loading and transport
• Commissioning
• Troubleshooting and repair
• Waste disposal
Certain work concerning maintenance and repair
must only be carried out by an expert workshop.
Such work is identi󰘰ed with the additional com-
ment Workshop work.
9

Children in danger
Children are not able to assess dangers and may
behave unpredictably. Children are therefore
especially endangered:
¾Keep children away from the machine.
¾Especially before drive o󰘯 and before trigger-
ing machine movements you must make sure
that the danger zone is free of children.
¾Shut down the tractor before leaving it.
Children can trigger dangerous machine
movements. An insu󰘲ciently secured ma-
chine parked without being attended poses
a danger for playing children!
Personal protective outt
WARNING
Health hazards caused by accidental con-
tact with crop protection agents or spraying
mixture!
Wear personal protective out󰘰t:
¾when preparing the spraying mixture
¾when cleaning / replacing the spraying noz-
zles, during spraying operation, during all
work for cleaning the crop protection sprayer
after spraying operation.
To wear the required protective out󰘰t always
observe the operating instructions and the safety
data sheet of the crop protection agent used.
Missing or incomplete protective equipment
increases the risk of health damage. Personal
protective equipment includes, e.g.:
¾overall resistant to chemicals
¾protective gloves resistant to chemicals
¾shoes resistant to chemicals
¾face protection
¾safety goggles to protect against splashes
¾Respirator
¾Provide effective protective equipment in
proper condition.
¾Never wear rings, bracelets or other jewellery.
Wear the personal protective out󰘰t stipulated
in the safety data sheet of the crop protection
agent last used when cleaning the crop protec-
tion sprayer.
NOTE
The owner must provide the necessary personal
protective out󰘰t as speci󰘰ed by the manufacturer
of the crop protection agent used.
NOTE
Do not enter the tractor cabin with contami-
nated protective outt!
Safety in tra󰀩c
DANGER
No passengers are allowed to ride on the
machine!
¾Pay attention to the permissible transport
widths and heights. Pay attention to the trans-
port height when passing under bridges and
low hanging overhead power lines.
¾When driving on public roads comply with the
respective national road tra󰘲c regulations!
¾Do not exceed the permissible axle load, tyre
load bearing capacity and total weight, in or-
der to ensure su󰘲cient steering and braking
capabilities. The front axle must be loaded
with at least 20 % of the tractor weight.
¾For machines without brake select the weight
of the tractor and the speed so that the ma-
chine can be managed securely under all
conditions.
¾The tractor must ensure the adequate supply
of the brake system of the connected vehicle.
10

¾Travel characteristics, steering and braking
ability are in󰘱uenced by attached or hitched
up equipment and ballasting weights. You
should therefore pay attention to su󰘲cient
steering and braking ability!
¾Before road travels check the correct connec-
tion of the supply lines:
• the brake and hydraulic system for apparent
faults
• whether the parking brake is fully released
• function of the service brake
For road transport the machine must be set to
transport position. The folding boom must be
folded up and secured. The stroke of the paral-
lelogram and optional steering must always be
blocked via the shut-o󰘯 valve before road travel,
see chapter shut-off valve.
¾Check lighting, warning and protective features
for functioning and cleanliness.
The permissible maximum speed speci-
󰘰ed in the type approval must be com-
plied with for transport on public roads!
The speci󰘰cations in the type approval
document or in the technical data are
decisive for the design dependent top
speed.
Always match the travel mode to the
road conditions to avoid accidents and
damage to the undercarriage.
Consider your personal abilities, carriage
way, tra󰘲c, sight and weather conditions.
In addition, pay attention to the notes in
chapter Commissioning!
Safety in operation
Commissioning
The operational safety of the machine cannot be
guaranteed without orderly performed commis-
sioning. This can lead to accidents with severe
or even fatal physical injuries.
¾The machine must only be put into operation
after receiving instructions by employees of
the authorized dealer or a HORSCH em-
ployee.
¾The machine registration form must be com-
pleted and returned to HORSCH.
All protective features and safety equipment,
such as detachable protective devices (wheel
chocks, etc.), must be correctly in place and
reliably functioning before the machine is put
into operation.
¾Check nuts and bolts, especially on wheels,
regularly for a tight 󰘰t and re-tighten if neces-
sary.
¾Check the tyre pressure at regular intervals,
see maintenance overview.
Damage to the machine
Damage to the machine can impair the op-
erational safety of the machine and cause ac-
cidents. This can lead to severe or even fatal
physical injuries.
The following machine parts are particularly
important for safety:
¾Hydraulics
¾Brakes (if available)
¾Connecting features
¾Protective features
¾Lighting
11

If in doubt about the safety-relevant status of
the machine, e.g. in case of leaking operating
󰘱uids, visible damage or unexpected changes
in travel behaviour:
¾Immediately shut down and secure the ma-
chine.
¾If possible locate and rectify the faults by fol-
lowing these operating instructions.
¾Rectify possible causes for damage (e.g. re-
move dirt and tighten loose screws).
¾Have damage that could a󰘯ect safety and
that cannot be recti󰘰ed by you recti󰘰ed by a
quali󰘰ed expert workshop.
Hitching and uncoupling
Faulty coupling of the machine to the pulling tool
of the tractor causes dangers, which could result
in severe accidents.
¾Strictly comply with all operating instructions:
• These operating instructions (chapter Con-
necting, Transport position and Parking)
• Operating instructions of the tractor
• if necessary the operating instructions for
the propshaft
¾Exercise special caution when reversing the
tractor. Never stand between tractor and
machine.
¾Only park the machine on a 󰘰rm and level
surface.
¾Secure the machine against rolling away.
¾Do not uncouple the machine with the folding
boom unfolded, with empty spraying mixture
containers. Negative drawbar load can cause
the crop protection sprayer to tip over.
Hydraulics
The hydraulic system is under high pressure.
Escaping 󰘱uid can penetrate the skin and cause
serious injuries. In the event of injury, consult a
doctor immediately.
The machine’s hydraulics has several functions,
which can cause injury to persons or damage to
the machine if operated incorrectly.
¾Do not connect/disconnect hydraulic hoses
to/from the tractor before both the hydraulics
on machine and tractor are de-pressurised.
¾Lock all hydraulically operated parts before
any work on the hydraulic system. Depres-
surise the hydraulics on the tractor and im-
plement side.
¾The hydraulic system is under high pressure.
Check all lines, hoses and screwed con-
nections regularly for leaks and any visible
external damage!
¾Use only appropriate means when searching
for leaks. Repair any damage immediately!
Oil sprays can cause injuries and 󰘰re!
¾Power sockets and connectors on the hydrau-
lic connections should be marked in order to
exclude operating errors.
¾In the case of injury, contact a doctor imme-
diately!
¾Secure and lock the control unit on the tractor
if not in use!
¾Replace hydraulic hoses at the latest after six
years, see Maintenance overview.
Pressure accumulator
The hydraulic system may be equipped with
pressure accumulators.
¾Do not open or work (welding, drilling) on
pressure accumulators. Even when empty,
the tanks are still preloaded by gas pressure.
The hydraulics must be depressurized before
maintenance!
12

Brake system
Depending on the equipment, the machines can
be equipped with a pneumatically or hydrauli-
cally operated service brake system.
For road travel the brake system must always
be connected and fully functional.
¾After coupling the machine and before trans-
portation you should always check the func-
tion and condition of the brake system.
¾Check the setting on the brake pressure
regulator.
¾Always release the parking brake before start-
ing to drive.
¾Always secure the machine against rolling
away and apply the parking brake before
unhitching.
Adjustments and repair work on the brake sys-
tem must only be carried out in a professional
workshop or by an operator, who has been
specially trained by HORSCH for this purpose.
Overhead lines
When unfolding or folding the folding boom, the
machine may reach the height of overhead lines.
Possible voltage 󰘱ashover to the machine may
cause fatal electric shock or 󰘰re.
¾Keep a safe distance to electric high voltage
power lines when unfolding or folding the fold-
ing boom.
¾Never unfold or fold the folding boom in the
vicinity of power poles and power lines.
¾With the folding boom unfolded and raised,
keep a su󰘲cient distance to electric high volt-
age power lines.
¾Never leave or access the machine under
overhead lines to avoid possible risks of
electric shock or voltage 󰘱ashover.
¾When operating the sprayer under high volt-
age power lines disable the BoomControl and
operate the slope compensation manually.
What to do in case of voltage ashover
Voltage 󰘱ashover generates high electric volt-
ages on the outside of the machine. This results
in extreme voltage di󰘯erences at the ground
around the machine. Wide strides, laying on the
ground or supporting yourself with your hands
on the ground can cause life-threatening electric
currents (pace voltage).
¾Do not leave the cabin.
¾Do not touch any metal objects.
¾Do not create a conductive connection to
ground.
¾Warn persons: DO NOT come near the ma-
chine. Electric voltages at the ground can
cause severe electric shock.
¾Wait for professional rescuers. The overhead
power line needs to be switched o󰘯.
If persons need to leave the cabin despite the
voltage 󰘱ashover, e.g. in case of a potential life-
threatening risk of 󰘰re:
¾Jump away from the machine. Ensure a safe
stand when jumping. Do not touch the outside
of the machine.
¾Move away from the machine with short step-
ping strides.
PTO-shaft / propshaft
Persons can be caught, pulled in and seriously
injured by the rotating PTO-shaft or propshaft.
Before switching on the PTO-shaft:
¾Always make sure that the PTO-shaft guard
is in place and fully functional.
¾Make sure that the chosen rotary speed and
the sense of rotation of the propshaft or PTO-
shaft correspond with the permissible values
for the machine.
¾Make sure that no persons are inside the dan-
ger zone around the PTO-shaft or propshaft.
Never switch on or couple the PTO-shaft while
the tractor motor is shut down.
¾Shut down the PTO-shaft if the angles are too
large. The machine could become damaged.
Parts may be thrown o󰘯 and injure persons.
13

¾Switch o󰘯 the PTO-shaft if it is no longer
needed.
¾Ensure su󰘲cient overlapping of pro󰘰le tube
and PTO-shaft guard.
¾Allow PTO-shaft locks to click into place.
¾Secure the PTO-shaft guard with chains
against rotating.
¾Before assembly/disassembly of the prop-
shaft as well as before all interventions on
the machine:
Uncouple the PTO-shaft (shut o󰘯 from the
tractor cab), switch o󰘯 the tractor engine, pull
o󰘯 the ignition key and wait until all parts have
come to a standstill.
¾Follow the operating instructions for the
propshaft.
Technical limiting values
If the technical limiting values of the machine
are not complied with, the machine may sustain
damage. This can lead to accidents with severe
or even fatal physical injuries.
The following technical limiting values are of
particular importance for safety:
• Permissible total weight
• maximum axle loads
• maximum drawbar load
• Top speed
See chapter Technical data, type plate and type
approval.
¾Also pay attention to the max. permitted loads
for the tractor.
Use in the eld
DANGER
No passengers are allowed to ride on the
machine!
¾Observe the national legislation and regula-
tions on crop protection!
¾The personal protective out󰘰t stipulated in
the safety data sheets of the crop protection
agent manufacturers must be carried along
and worn during work.
¾Check the area immediately around the ma-
chine (for children!) before driving o󰘯 and
commissioning the machine. Ensure su󰘲cient
visibility.
¾Check the condition of the folding boom and
their mounting before use.
¾Ensure su󰘲cient stability of the machine in
case of longitudinal or transverse inclination
when working in uneven terrain. Pay attention
to the limiting values for the tractor.
¾Do not remove any of the mandatory and
supplied protective devices.
¾Stay clear of the operating range of hydrauli-
cally operated parts.
¾Use accessing aids and steps only at stand-
still.
¾At the headland reduce the travel speed and
disable spraying.
¾Excessive, jerky steering movements at the
beginning and the end of a curve will put ex-
treme loads on the folding boom.
¾The spraying agent may be blown away if the
droplets are 󰘰ne and the wind is strong. This
may cause damage to people and nature!
¾If the soil is very dry, the applied chemical can
be blown away together with dust and cause
damage. Ensure su󰘲cient moisture of the soil!
¾For tractors with cabins with ventilation fans
replace the fresh air 󰘰lters with activated-
carbon 󰘰lters! Observe notes and instructions
of the tractor manufacturer.
¾Ensure that the category of the tractor cabin
is approved for the respective crop protection
agent used.
¾Always ensure a su󰘲cient water supply in the
machine to be able to wash o󰘯 crop protection
agent in events of emergency.
¾Data concerning the preparations currently
used must always be kept in the document roll
so that these are available for rescue services
in case of accidents.
14

Changing equipment / wear items
¾Only pulling tools may be attached that meet
the technical requirements according to these
operating instructions.
HORSCH does not assume any liability for
damages resulting from the attachment of
non-󰘰tting pulling tools as well as incorrect
mounting.
¾For machines with valid type approval only
pulling tools may be attached that are covered
by the type approval. Attaching pulling tools
not covered by the type approval will void the
registration.
¾Secure the machine against unintended roll-
ing away!
¾Secure raised frame parts you have to work
under with suitable supports!
¾Caution! Risk of injury caused by projecting
parts (e.g. folding boom parts)!
¾Assume ergonomic working postures with any
assembly work.
Do not step on moving or other rotating parts to
climb onto the machine. You could fall and be
seriously injured.
Crop protection agents
and liquid fertiliser
Improper handling of crop protection agents and
liquid fertiliser may cause poisoning and death.
¾Follow the speci󰘰cations and instructions in
the safety data sheet of the crop protection
agent manufacturer. If necessary, ask the
dealer for the safety data sheet or safety
notes.
¾Determine and provide the personal protective
out󰘰t as speci󰘰ed by the manufacturer of the
crop protection agent.
¾At the time the crop protection sprayer is
manufactured the manufacturer is aware of
only a few approved crop protection agents,
which could have a damaging e󰘯ect on the
materials used in the crop protection sprayer.
¾Store all relevant information about the crop
protection agents used (safety data sheets,
instructions for use, etc.) in the document roll.
¾The water quality (the water hardness and
mineral content in particular) in󰘱uences the
property of some fertilisers and crop protec-
tion agents. Precipitation and de󰘱occulation
can cause deposits in 󰘰lters and nozzles.
Example: Extremely hard water reacts with
sulphate-bearing fertiliser to form calcium
sulphate (gypsum) and causes white deposits
in the 󰘰lters.
Pay attention to the conditions of use and
the combination possibilities given by the
corresponding manufacturers to avoid such
problems!
¾Observe the data on compatibility of crop
protection agents with materials of the crop
protection sprayer!
¾Do not spray any crop protection agents that
have a tendency to agglutination or solidi󰘰ca-
tion!
¾Wear suitable protective clothing when han-
dling crop protection agents.
¾Do not eat, drink or smoke while handling crop
protection agents!
¾Keep crop protection equipment and crop
protection agents out of the reach of children!
¾Always ensure a su󰘲cient water supply in the
machine to be able to wash o󰘯 crop protection
agent in events of emergency.
¾In case of physical contact with crop protection
agents you may need to consult a physician.
¾Thoroughly clean hands and face after the
end of work.
¾Extended exposure time of crop protec-
tion agents may cause damages to plastic
components of the crop protection sprayer.
Follow the notes of the crop protection agent
manufacturers.
¾The application notes of the crop protection
agent manufacturers must be observed when
mixing di󰘯erent crop protection agents.
15

Environmental protection
Crop protection agents and liquid fertiliser as
well as operating materials such as hydraulic
oil, lubricants, etc. can damage the environment
and the health of persons.
¾Do not allow operating materials to drain out
into the environment.
¾Pick up drained operating materials with ab-
sorbent material or sand, 󰘰ll it into a leak tight
container and dispose of in accordance with
statutory regulations.
¾Do not 󰘰ll crop protection sprayers with water
from public bodies of water.
¾Filling in water protection zones is not permit-
ted, depending on the crop protection agent
used! Inquire with the “Water board” to be on
the safe side!
¾Observe the national and country-speci󰘰c
regulations and standards (e.g. water protec-
tion areas).
Retrotting and
conversions
Structural changes not approved by HORSCH
may a󰘯ect the functionality and operational
safety of the machine and will void any warranty
claim.
HORSCH is not liable for damages to life and
limb as well as property damages resulting from
unapproved retro󰘰tting and conversions.
¾Do not perform any structural changes to the
pulling tool of the machine.
¾Do not make any structural changes or ex-
tensions to the machine that have not been
approved by HORSCH.
¾Modi󰘰cations and extensions approved by
HORSCH are only to be performed at an au-
thorized workshop or by an operator who has
been trained by HORSCH for this purpose.
¾Comply with country-speci󰘰c instructions for
weights, weight distribution and dimensions.
For equipment in󰘱uencing the weight or weight
distribution the regulations concerning towing
facility, support and axle load must be checked
and complied with.
For machines without brakes a brake system
may need to be retro󰘰tted if the permissible
weight limits are exceeded.
In case of changes concerning data mentioned
on the type plate, a new type plate with updated
data must be attached.
In case of changes which concern the data in
the type approval, this type approval needs to
be renewed.
Care and maintenance
Inappropriate care and maintenance puts the
operational safety of the machine at risk. This
can lead to accidents with severe or even fatal
physical injuries.
DANGER
¾Danger of poisoning - Do not climb into
the spraying mixture container!
¾Conform to prescribed schedules for repetitive
tests or inspections.
¾Service the machine according to the mainte-
nance plan, see chapter Care and maintenance.
¾Only perform the work described in these
operating instructions.
¾Before starting maintenance and service work
park the machine on level and 󰘰rm ground and
secure it against rolling away. Clean the crop
protection sprayer, especially all parts which
are contaminated by spraying mixture. Wear
the stipulated protective out󰘰t when cleaning.
¾Lock hydraulically operated parts and depres-
surise the hydraulic system.
¾Prior to working on the electrical system,
disconnect it from the electric current supply.
16