Hoshizaki HS-5245 User manual

12A8478-013
Hoshizaki Prison Kit
HS-5245, HS-5246, HS-5252, HS-5253,
HS-5254, HS-5255, HS-5426, HS-5427
For use with Hoshizaki Ice Machines: KM-350M_J, KM-520M_J, KM-660M_J,
KM-901M_J, KM-1301S_J/3, and KM-1900S_J/3
Check to ensure that all parts are included:
Index
No. Description
Kit
Number Model
Part
Number Qty
1 Front Panel HS-5426 KM-350MAJ, KM-520MAJ, KM-660MAJ 3B0020G01 1
HS-5427 KM-350MWJ, KM-520MWJ, KM-520MRJ, KM-660MWJ, KM-660MRJ 1A5320G01 1
HS-5245 KM-901MAJ 2A8612G01 1
HS-5246 KM-901MWJ 2A8612G02 1
HS-5252 KM-1301SAJ/3 2A7289G01 1
HS-5253 KM-1301SWJ/3 2A7251-01 1
HS-5254 KM-1900SAJ/3 2A7292G01 1
HS-5255 KM-1900SWJ/3 2A7252-01 1
2 Torx Screw (4 mm-small) All All 7PP2I0812 20
3 Torx Screw (4 mm-large) All All 7PP2-0410 6
4 Torx Screw (5 mm) All All 7PP2-0512 3
5 Torx Pin Bit (small) All All 7PP2-0001 1
6 Torx Pin Bit (large) All All 7PP2-0002 1
WARNING
• Only qualied service technicians should install this kit to reduce the risk of death, electric shock, serious injury, or re.
• Move the icemaker control switch to the "OFF" position and turn off the power supply before servicing. Lockout/Tagout to
prevent the power supply from being turned back on inadvertently.
• CHOKING HAZARD: Ensure all components, fasteners, and thumbscrews are securely in place after any maintenance is
done to the appliance. Make sure that none have fallen into the ice storage bin.
• No installation or service should be undertaken until the technician has thoroughly read these instructions.
Installation Instructions
1) Turn off the power supply. Lockout/Tagout to prevent the power supply from being turned on inadvertently.
2) Remove and discard the front panel and screw(s). See Fig. 1 and Fig. 2.
3) Place the new front panel in its correct position and secure with Torx screw(s) (4 mm-large) provided in this kit.
4) Remove all screws from the sides of the appliance (KM-1301 and KM-1900S_J/3) and replace with Torx screws (4 mm-large)
provided in this kit. See Fig. 2.
Fig. 2
Model Shown:
KM-520MAJ
Fig. 1
4 mm-large
Model Shown:
KM-1900SAJ3
4 mm-large
4 mm-large
4 mm-large
Side
Side

22A8478-013
5) Remove all but the drain valve tting screws from the rear of the appliance and replace with Torx screws (4 mm-small) provided in
this kit. See Fig. 3 and Fig. 4.
6) Remove the drain valve tting screws and replace them with Torx screws (5 mm) provided in this kit.
7) Dispose of any remaining screws.
4 mm-small
4 mm-small
5 mm
4 mm-small4 mm-small
4 mm-small
4 mm-small
5 mm
Model Shown:
KM-520MWJ
Model Shown:
KM-1900SWJ3
Fig. 3
Fig. 4
Drain Valve
Fitting
Drain Valve
Fitting
4 mm-small