Hoyles Exitguard ex200 series User manual

Door Switch Contact Rd/Yl

EX204 Battery powered for use where a 4. OUT OF THE BOX factory default settings

separate supply of power is not available and are suitable for most applications. On first use

the protected door is opened infrequently or we recommend that you use these settings to

there is no requirement to sound the sounder test the EXITGUARD. They can be changed

for long periods. Can be powered from 12vdc if later to suit local requirements.Test by entering

necessary. (Discard batteries) the user code and pressing Ifor Chime Mode.

A chime will be heard each time the door is

EX205 12vdc powered for use where the

opened.

protected door may be opened frequently or

Advanced Installation

the integral sounder needs to sound for

The following parameters can be changed

protracted periods. This version can also be

through the keypad:

interfaced with other equipment. There are volt

1. User Code

free relay contacts to separately signal

2. Select one of six different alarm tones

ON/OFF status and alarm conditions at remote

3. Change auto re-arm delay 0 - 88 secs

points. Cannot be powered from batteries.

4. Change Door Open Too Long (DOTL1)

EX206 230vac powered version where the delay for keypad reset mode 0 secs - 88 mins.

protected door may be opened frequently or 5. Change DOTL2 delay for auto reset mode

the sounder needs to sound for protracted 0secs - 88mins.

periods. There is a volt free alarm relay contact. 6. Switch Bleep In Off (BIO) on or off.

This version is supplied with 6 x AA alkaline 7.Add or change a Reset/Pass Code

batteries for standby - Note: the batteries will 8. Add or change a Manager Code.

not power the alarm relay.

OUT OF THE BOX User Operation.

All versions have key pad control, integral There are four possible modes:

sounder with programmable tones, 5 mode Off Mode

LEDs, a front/back acting tamper switch and a Chime Mode I

logic output to signal to a MULTIGUARD

Keypad Reset Mode II

indicator from HED. All are supplied with a door

Auto re-arm Mode III

contact, fixing screws and door warning label.

Quick Install When the User Code is entered the

EXITGUARD is interrogated and one of the

EXITGUARDS are NOT intended for external mode LEDs illuminates to indicate the current

use and to avoid damage should not be fixed to status.

the protected door itself. After the User Code is entered there is a 5sec

1.The door contact is in two parts; the magnet window to change the mode, eg. If the current

should be fixed to the door and the contact with mode is OFF and it is desired to switch to the

its cable fitted to the frame. The cable should Keypad Reset mode just enter II ie 2 on the

be taken to the EXITGUARD and connected as keypad. Within 5secs the LED will extinguish. If

shown. Ais the alarm input for the switch a mistake has been made this can be rectified

element (RD/YL) of the contact and Tis from before the LED extinguishes by simply

the tamper loop (BL/BK) of the contact. selecting the desired mode, the LED indication

2. Make all connections, apply power, a double will change to the new mode.

bleep will be heard and the four mode LEDs will If the Auto re-arm mode is selected then the

illuminate. factory default period of 30secs will be used

3. When the EXITGUARD leaves the factory unless set up differently. (see programming

there are no codes in memory. The four instructions to change the Auto re-arm period

illuminated red LEDs are inviting you to and other functions)

enter a User Code. This must be a four digit

memorable code. As the code is entered

acknowledge bleeps are heard and each of

the mode LEDs will extinguish. The code is

now stored in memory and the EXITGUARD

will emit a double bleep and should be in the

OFF mode.

BK RD PP

HED

Door Switch tamper

loop Bl/Bk

These relay contacts

change state when the

EXITGUARDis armed.

EX205 only.

These relay contacts

change state when an

alarm condition is

generated.

EX205 & EX206 16vac

These terminals

are only used on

EX204 & EX206

If required the tamper switch To can be:

a. wired in series with the Blue or Black door switch

tamper loop to give an audible alarm at any time.

b. wired in series with the Red or Yellow of the door

switch contact pair to give an alarm condition only

when the Exitguard is armed.

c. wired to a remote device to give a warning at a

remote location.

d. ignored and not connected at all.

The on board tamper switch is

connected to these two terminals, To

If the tamper switch is required fit the spring

ensuring contact with the wall when the lid is fitted,

and operates when the lid is removed.

12vdc

EX204 Apply 12vdc (140ma max) here if required.

EX205 Apply 12vdc (165ma max) here.

EX206 12vdc available here @ 100ma max when mains power is available.

EXITGUARD EX200 series Installation Instructions

RELAY 1 RELAY 2

Input for Fire Door Checker (see scenario 4) Or Temporary Pass through (see scenario 7)

Apply 12vdc +ve to invoke Fire Door Checker. This can be

derived from an intruder, time clock or keyswitch etc..

Apply momentary 12vdc +ve for return pass through.

Factory Default.

To restore the factory default settings

disconnect power completely for about 10

secs. Ensure the door contact & tamper loop

are open. Move the SYSTEM RESET

jumper J1 from its normal position to the

reset position. Re-apply power four bleeps

will be heard. Replace the jumper to the

normal position. Two beeps will be heard

and the four mode LEDs should be

illuminated inviting you to enter a new user

code. Re-close the tamper & door contact..

The Factory default settings are as follows:

User Code None

Auto re-arm period 30 seconds

DOTL1 delay 00 seconds

DOTL2 delay 00 Seconds

Sounder Tone 1

III

Chime mode

Off

Keypad reset mode

Auto re-arm mode

exitguard

Mode

LEDs

Power LED

Setup LED

COM

SYSTEM J1

RESET

{

MULTIGUARD 2000 - 6

O/P to optional MULTIGUARD

Neutral

Earth

1 AMP

230vac

Transformer is fitted in the enclosure back

box and is pre-wired to the circuit board.

EX206 Mains Powered Version Only

DWG No: 60112 Issue 2, Nov 2013

4 5 6

7 8 0

IIIIII IIIIII

Keypad

T. 01744 886600 F. 01744 886607 E. [email protected] W. www.hoyles.com

Hoyles Electronic Developments Ltd

NORM

RESET

8mm (max gap)

Magnetic Door Contact.

Fit to door frame and

protect from moisture

Magnet. Fit to door

& align with contact

EXITGUARD Set-up

Bleep In Off (BIO).

Scenario 6. Temporary Pass Through

Tone Select.

Add or change a Reset/Pass Code.

Scenario 1. Typical Fire Exit Door.

High Level Security.

Add or Change a Manager Code.

Scenario 2. Shop or Reception Door. Auto re-arm period.

Programming.

Scenario 3. Fire Door Checker.

Door Open Too Long Delay for Keypad

reset mode (DOTL1.)

Leave Set-up Mode.

To Enter Set-up Mode.

Scenario 4. Loading Bay Door.

Changer User Code.

Scenario 5. Fire Stop Corridor Door.

Door Open Too Long Delay for Auto re-arm

Mode (DOTL2.)

closer spring is fitted. Arm the EXITGUARD in III code is pressed an LED will extinguish. When the to the procedure for DOTL1 above

mode. code is complete a double bleep is heard. The unit

The EXITGUARD contains a non volatile memory

remains in the SET-UP mode and further

(NVM). The User Code and any programmed

programming can be carried out following the

functions are stored in this NVM even if power is

instructions below.

lost for long periods. If you have forgotten the In Set-up mode BIO can be toggled On and Off .

User Code (or manager code if used) it will be The default factory setting is Off,

necessary to reset to the factory default settings. In Set-up mode enter 6. If one bleep is heard then

Any functions that you have programmed will be BIO is off, if two bleeps are heard then BIO is on.

lost. In Set-up mode enter 2. A bleep is heard and a Successively pressing 6 will toggle BIO on and off.

Before altering any functions such as the re-arm single mode LED illuminates to indicate that a one

period or door open too long delays (DOTL) etc.. digit number in the range 1 - 6 is needed.

consider if the factory defaults will meet your The tones are:

requirements. The following scenarios are quite 1 & 2. High (Factory default setting is 1) In set-up mode enter 7. A single bleep is heard and

typical. The first four involve no programming Ear defenders are recommended!!!!! four mode LEDs illuminate inviting you to enter a

other than setting the User Code. The remaining 3 & 4. Normal four digit Reset/Pass Code PPPP. As each digit is

scenarios require a little programming. 5 & 6. Low entered an LED will extinguish. When the code is

complete a double bleep is heard. The Set-up LED

If an incorrect digit is entered a ‘Barp’ will be heard

An audible alarm is required when the door is continues to flash to indicate that you are still in the

and the LED continues to indicate that a single digit

opened. Use the factory default settings and arm In some applications it may be necessary to allow only Set-up mode. Ensure DOTL1 and DOTL2 are set.

is still required. When a correct digit is entered the a

selected persons to change the various parameters. A

the EXITGUARD for either Keypad reset II or short sample of the tone is played with the strobing

Manager Code gives an extra level of security by only

Auto re-arm III mode. ie. the EXITGUARD LEDs to indicate the selected tone. The Set-up LED

allowing a manager to change:

silences and re-arms after a 30 second delay if the flashes to indicate that you are still in Set-up mode.

A. User and Pass & Manager Codes

door has been closed. Enter 0 to leave if set-up is complete. In set-up mode enter 8. a triple bleep is heard and

B. Bleep In Off (BIO)

four mode LEDs illuminate inviting you to enter a

C. Auto re-arm delays

A chime is required each time the door is opened. four digit Manager Code MMMM. As each digit is

Use the factory default settings and arm the D. Door Open Too Long delays (DOTL)entered an LED will extinguish. When the code is

EXITGUARD for Chime I mode. complete a double bleep is heard. To change any

In Set-up mode enter 3. A bleep is heard and two

Before the EXITGUARD can be programmed a User further settings in future you will need to use the

mode LEDs will illuminate to indicate that a two digit

Code must have been set up as detailed overleaf. The

The EXITGUARD can be used to verify that all Manager Code in order to enter the set-up mode

number corresponding to the required period eg. 00

following functions can be programmed into the NVM:

Fire Exit Doors are available for use when a rather than the User Code.

for instant re-arm, 05 for 5secs, 88 for 88secs etc..

building is occupied. The R terminal of each 1. Four digit User Code.As the digits are entered the LEDs extinguish and a Note: If the EXITGUARD has been set up with a

EXITGUARD is connected to a switched +ve 2. Select one of six different alarm tones double bleep is heard when both digits have been Manager Code then both the User Code and

12vdc of the building’s intruder alarm. When the 3. Change auto re-arm time 0 - 88 seconds entered. The Set-up LED continues to flash to Manager Code must be used to enter the set-up

alarm is set this signal is applied to the 4. Change DOTL1 delay for keypad reset mode 0 indicate that you are still in the Set-up mode. mode and change any settings. Proceed as

EXITGUARDs. When the intruder alarm is un-set seconds - 88 minutes. follows:

the signal is removed and the EXITGUARDs will 5. Change DOTL2 delay for auto reset mode 0 Enter the User Code UUUU, Press and hold 7.

strobe and double bleep every 30 secs. Opening seconds - 88 minutes. The LED illuminates steady. Enter the

and re-closing the door causes the strobing and Manager Code M MM M,the LEDflashes.

6. Switch Bleep In Off (BIO) on or off.

the periodic bleeps to cease. The EXITGUARD To delete a Pass or Manager Code use the User

7.Add or change a four digit Reset/ Pass Code.In Set-up mode enter 4. A bleep is heard and the

then automatically reverts to the mode it was set to Code for either or both..

8. Add or change a four digitManager Code.bottom two mode LEDs illuminate to request a two

during the previous period of occupancy; O, I, II

Programming is carriedout in Set-upmode digit number for minutes eg. 00 for zero mins 05 for

or III. If the intruder alarm has been set in error it 5mins, 88 for 88 mins etc.. As the digits are entered

can be un-set and re-set without the necessity to the LEDs extinguish and a single bleep is heard

open and re-close all doors for checking. when both digits have been entered. The top two In Set-up mode enter 0, a double bleep is heard as the

mode LEDs now illuminate requesting a two digit EXITGUARD leaves set-up mode. The EXITGUARD

To enter the this mode type the User Code UUUU and

Invoke the Bleep In Off facility (see programming will now be in the OFF mode as indicated by the OFF

number for seconds eg. 00 for zero secs, 15 for

hold down the 7 key until two beeps are heard. The

below). Arm the EXITGUARD in Keypad reset II LED. Whilst this LED is illuminated the EXITGUARD

15secs up to a maximum of 58secs. The maximum

Set-up LED flashes. To leave this mode type 0. The

mode. Switch Off with keypad for deliveries. The can be switched

is therefore 88m58s. A double bleep is heard when

system always reverts to the OFF when leaving Set-

Bleep In Off will remind staff to re-arm the to any other mode

all digits have been entered correctly. The Set-up

up. See also Manager Code later.

EXITGUARD after each delivery. I, II or III or

LED continues to flash to indicate that you are still in even back to Set-

the Set-up mode. up mode by

Staff are able to pass through the door without pressing and

generating an alarm but if left open then an alarm holding 7.

will be generated. Set the Auto re-arm period at 00 In Set-up mode enter 1, a double bleep is heard and

and DOTL2 delay at 10. Door must be closed the four mode LEDs will illuminate inviting you to enter

within 10 seconds. It is recommended that a door a new four digit User Code UUUU. As each digit of the In Set-up mode enter 5. The procedure is identical

In this scenario a Pass Code is used to allow passage

through to say a storeroom without the necessity to

switch the EXITGUARD Off. When using a pass code